main
History Download
Ray Publish 0.1.0 6dd3316

LMH1983SQ

Texas Instruments · Video Interface ICs · WQFN-40-EP(6x6)

LMH1983SQ from Texas Instruments, in a WQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in 3.3-V supply for PLL1.
2 VDD power_in 3.3-V supply for logic I/O.
3 Hin input Horizontal sync reference input (LVCMOS); auto polarity correction for HVF is based on Hin polarity, and recognized clock inputs can be applied to Hin.
4 Vin power_in Vertical sync reference signal input (LVCMOS).
5 Fin input Field sync (odd/even) reference signal input (LVCMOS).
6 INIT input Reset signal for audio-video phase alignment, rising edge triggered (LVCMOS).
7 ADDR input I2C address select (LVCMOS): tie low for 0x65, float for 0x66, tie high for 0x67 (7-bit slave address).
8 SDA bidirectional I2C data signal, which requires a 4.7 kΩ pull-up resistor to the VDD supply.
9 SCL input I2C clock signal, which requires a 4.7 kΩ pull-up resistor to the VDD supply.
10 VDD power_in 3.3-V supply for logic I/O.
11 NO_LOCK output Loss of lock status flag for PLLs 1-4, active high, derived from the Lock Status register bits that can be masked.
12 NO_ALIGN output Loss of alignment status flag for OUTs 1-4 (LVCMOS, active high).
13 NO_REF output Loss of reference status flag (LVCMOS, active high).
14 CLKout4- output LVDS audio clock from PLL4 with fundamental rate 98.304 MHz, defaulting to 24.576 MHz and selectable via the host.
15 CLKout4+ output LVDS audio clock from PLL4 with fundamental rate 98.304 MHz, defaulting to 24.576 MHz and selectable via the host.
16 VDD power_in 3.3 V supply for CLKout4.
17 Fout4 (OSCin) bidirectional Audio frame timing signal for OUT4 (active low, LVCMOS), fixed to the PLL4 clock; optionally applies a 27 MHz external clock to PLL4 when enabled via the host.
18 GND power_in Ground.
19 VDD power_in 3.3 V supply for PLL3 and PLL4.
20 VDD power_in 3.3 V supply for CLKout3.
21 GND power_in Ground.
22 Fout3 output Video frame timing signal for OUT3 (active low, LVCMOS), assignable to PLL1, PLL2, or PLL3.
23 CLKout3+ output LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.35 MHz and selectable via the host.
24 CLKout3- output LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.35 MHz and selectable via the host.
25 Cbyp3 passive Bias bypass for the on-chip LDO of PLL3; connect to 1.0 µF and 0.1 µF bypass capacitors.
26 Cbyp4 passive Bias bypass for the on-chip LDO of PLL4; connect to 1.0 µF and 0.1 µF bypass capacitors.
27 Cbyp2 passive Bias bypass for the on-chip LDO of PLL2; connect to 1.0 µF and 0.1 µF bypass capacitors.
28 CLKout2+ output LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.5 MHz and selectable via the host.
29 CLKout2- output LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.5 MHz and selectable via the host.
30 Fout2 output Video frame timing signal for OUT2 (active low, LVCMOS), assignable to PLL1, PLL2, or PLL3.
31 VDD power_in 3.3-V supply for CLKout2.
32 VDD power_in 3.3-V supply for PLL2.
33 XOin- input 27 MHz VCXO clock input for PLL1; in LVCMOS mode bias to mid-supply with a 0.1 µF bypass capacitor, and must be driven by a 27 MHz clock to read or write registers via I2C.
34 XOin+ input 27 MHz VCXO clock input for PLL1; in LVCMOS mode connect the clock directly, and in LVDS mode connect the LVDS clock signals to XOin+ and XOin-.
35 CLKout1- output LVDS video clock from PLL1, defaulting to 27 MHz and selectable via the host.
36 CLKout1+ output LVDS video clock from PLL1, defaulting to 27 MHz and selectable via the host.
37 Fout1 output Reference frame timing signal for OUT1 (active low, LVCMOS), fixed to the PLL1 OUT1 format that follows the reference input format.
38 VDD power_in 3.3 V supply for CLKout1.
39 GND power_in Ground.
40 VC_LPF output Loop filter for the PLL1 charge pump output with VCXO control voltage sensing; in free-run and holdover modes PLL1 is disabled and an internal DAC drives the VCXO control voltage.
41 DAP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-40-EP(6x6)
Category Interface
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD 3.6 V 5
Input voltage (any input) VI -0.3 V Any input; maximum printed as VDD + 0.3 V 5
Output voltage (any output) VO -0.3 V Any output; maximum printed as VDD + 0.3 V 5
Junction temperature TJMAX 150 °C 5
Storage temperature range Tstg -65 150 °C 5
Input voltage 0 V Maximum printed as VDD 5
Temperature range, operating free-air TA -40 85 °C 5
Thermal resistance, junction to ambient RθJA 33 °C/W 5
Total supply current IDD 170 212 mA Default register settings, no load on logic outputs. VDD = 3.465 V 6
Total supply current IDD 60 100 mA PLL2, PLL3 and PLL4 disabled, no load on logic outputs. VDD = 3.465 V 6
I2C input current IIN -10 10 μA VIN between 0.1 VDD and 0.9 VDD 7
Low output sink current IOL 1.25 mA VOL = 0V or 0.4V 6
Low output voltage, status flag outputs VOL 0.4 V IOUT = +10 mA 6
Low output voltage, frame timing outputs VOL 0.4 V IOUT = +10 mA; Fout1, Fout2, Fout3 6
Output shutdown leakage current, frame timing outputs IOZ 0.4 10 μA Output buffer shutdown, pin connected to VDD or GND; VDD = 3.465V 6
Differential signal output voltage VOD 247 350 454 mV 100 Ω differential load, CLKout1, CLKout2 or CLKout3 7
Common signal output voltage VOS 1.125 1.25 1.375 V 100 Ω differential load, CLKout1, CLKout2 or CLKout3 7
Change to VOD for complementary output states /VOD/ 50 mV 100 Ω differential load, CLKout1, CLKout2 or CLKout3 7
Change to VOS for complementary output states /VOS/ 50 mV 100 Ω differential load, CLKout1, CLKout2 or CLKout3 7
Output short circuit current IOS 24 mA Differential clock output pins connected to GND for CLKout1, CLKout2, or CLKout3 7
Output shutdown leakage current, clock outputs IOZ 1 10 μA Output buffer in shutdown mode, differential clock output pins connected to VDD or GND 7
Maximum relative frequency offset between VCXO input and H input fOFF -150 150 ppm Assumes H input jitter of ±15 ns 7
Single-ended signal input voltage range VXOin_SE 0 V Single-ended input buffer mode; maximum printed as VDD 7
Differential signal input voltage range VXOin_DIFF 247 350 454 mV Differential input buffer mode, VCM = 1.2 V 7
Auto-format detection time TAFD 2 4 Frames Time from when reference input first presented to when detected as indicated by NO_REF going low. Reference timing must be stable and accurate (no missing pulses). 6

CAD (KiCad official)

  • Symbol: LMH1983SQ
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: WQFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: lmh1983sq-etched.step / lmh1983sq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmh1983sq.step / lmh1983sq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (55 pp, sha256 b94fd5096487eedb, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF