3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMH1983SQ
Texas Instruments · Video Interface ICs · WQFN-40-EP(6x6)
LMH1983SQ from Texas Instruments, in a WQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | 3.3-V supply for PLL1. |
| 2 | VDD | power_in | 3.3-V supply for logic I/O. |
| 3 | Hin | input | Horizontal sync reference input (LVCMOS); auto polarity correction for HVF is based on Hin polarity, and recognized clock inputs can be applied to Hin. |
| 4 | Vin | power_in | Vertical sync reference signal input (LVCMOS). |
| 5 | Fin | input | Field sync (odd/even) reference signal input (LVCMOS). |
| 6 | INIT | input | Reset signal for audio-video phase alignment, rising edge triggered (LVCMOS). |
| 7 | ADDR | input | I2C address select (LVCMOS): tie low for 0x65, float for 0x66, tie high for 0x67 (7-bit slave address). |
| 8 | SDA | bidirectional | I2C data signal, which requires a 4.7 kΩ pull-up resistor to the VDD supply. |
| 9 | SCL | input | I2C clock signal, which requires a 4.7 kΩ pull-up resistor to the VDD supply. |
| 10 | VDD | power_in | 3.3-V supply for logic I/O. |
| 11 | NO_LOCK | output | Loss of lock status flag for PLLs 1-4, active high, derived from the Lock Status register bits that can be masked. |
| 12 | NO_ALIGN | output | Loss of alignment status flag for OUTs 1-4 (LVCMOS, active high). |
| 13 | NO_REF | output | Loss of reference status flag (LVCMOS, active high). |
| 14 | CLKout4- | output | LVDS audio clock from PLL4 with fundamental rate 98.304 MHz, defaulting to 24.576 MHz and selectable via the host. |
| 15 | CLKout4+ | output | LVDS audio clock from PLL4 with fundamental rate 98.304 MHz, defaulting to 24.576 MHz and selectable via the host. |
| 16 | VDD | power_in | 3.3 V supply for CLKout4. |
| 17 | Fout4 (OSCin) | bidirectional | Audio frame timing signal for OUT4 (active low, LVCMOS), fixed to the PLL4 clock; optionally applies a 27 MHz external clock to PLL4 when enabled via the host. |
| 18 | GND | power_in | Ground. |
| 19 | VDD | power_in | 3.3 V supply for PLL3 and PLL4. |
| 20 | VDD | power_in | 3.3 V supply for CLKout3. |
| 21 | GND | power_in | Ground. |
| 22 | Fout3 | output | Video frame timing signal for OUT3 (active low, LVCMOS), assignable to PLL1, PLL2, or PLL3. |
| 23 | CLKout3+ | output | LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.35 MHz and selectable via the host. |
| 24 | CLKout3- | output | LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.35 MHz and selectable via the host. |
| 25 | Cbyp3 | passive | Bias bypass for the on-chip LDO of PLL3; connect to 1.0 µF and 0.1 µF bypass capacitors. |
| 26 | Cbyp4 | passive | Bias bypass for the on-chip LDO of PLL4; connect to 1.0 µF and 0.1 µF bypass capacitors. |
| 27 | Cbyp2 | passive | Bias bypass for the on-chip LDO of PLL2; connect to 1.0 µF and 0.1 µF bypass capacitors. |
| 28 | CLKout2+ | output | LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.5 MHz and selectable via the host. |
| 29 | CLKout2- | output | LVDS video clock from PLL1, PLL2, or PLL3 depending on crosspoint mode, defaulting to 148.5 MHz and selectable via the host. |
| 30 | Fout2 | output | Video frame timing signal for OUT2 (active low, LVCMOS), assignable to PLL1, PLL2, or PLL3. |
| 31 | VDD | power_in | 3.3-V supply for CLKout2. |
| 32 | VDD | power_in | 3.3-V supply for PLL2. |
| 33 | XOin- | input | 27 MHz VCXO clock input for PLL1; in LVCMOS mode bias to mid-supply with a 0.1 µF bypass capacitor, and must be driven by a 27 MHz clock to read or write registers via I2C. |
| 34 | XOin+ | input | 27 MHz VCXO clock input for PLL1; in LVCMOS mode connect the clock directly, and in LVDS mode connect the LVDS clock signals to XOin+ and XOin-. |
| 35 | CLKout1- | output | LVDS video clock from PLL1, defaulting to 27 MHz and selectable via the host. |
| 36 | CLKout1+ | output | LVDS video clock from PLL1, defaulting to 27 MHz and selectable via the host. |
| 37 | Fout1 | output | Reference frame timing signal for OUT1 (active low, LVCMOS), fixed to the PLL1 OUT1 format that follows the reference input format. |
| 38 | VDD | power_in | 3.3 V supply for CLKout1. |
| 39 | GND | power_in | Ground. |
| 40 | VC_LPF | output | Loop filter for the PLL1 charge pump output with VCXO control voltage sensing; in free-run and holdover modes PLL1 is disabled and an internal DAC drives the VCXO control voltage. |
| 41 | DAP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-40-EP(6x6) |
| Category | Interface |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 3.6 | V | 5 | |||
| Input voltage (any input) | VI | -0.3 | V | Any input; maximum printed as VDD + 0.3 V | 5 | ||
| Output voltage (any output) | VO | -0.3 | V | Any output; maximum printed as VDD + 0.3 V | 5 | ||
| Junction temperature | TJMAX | 150 | °C | 5 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage | 0 | V | Maximum printed as VDD | 5 | |||
| Temperature range, operating free-air | TA | -40 | 85 | °C | 5 | ||
| Thermal resistance, junction to ambient | RθJA | 33 | °C/W | 5 | |||
| Total supply current | IDD | 170 | 212 | mA | Default register settings, no load on logic outputs. VDD = 3.465 V | 6 | |
| Total supply current | IDD | 60 | 100 | mA | PLL2, PLL3 and PLL4 disabled, no load on logic outputs. VDD = 3.465 V | 6 | |
| I2C input current | IIN | -10 | 10 | μA | VIN between 0.1 VDD and 0.9 VDD | 7 | |
| Low output sink current | IOL | 1.25 | mA | VOL = 0V or 0.4V | 6 | ||
| Low output voltage, status flag outputs | VOL | 0.4 | V | IOUT = +10 mA | 6 | ||
| Low output voltage, frame timing outputs | VOL | 0.4 | V | IOUT = +10 mA; Fout1, Fout2, Fout3 | 6 | ||
| Output shutdown leakage current, frame timing outputs | IOZ | 0.4 | 10 | μA | Output buffer shutdown, pin connected to VDD or GND; VDD = 3.465V | 6 | |
| Differential signal output voltage | VOD | 247 | 350 | 454 | mV | 100 Ω differential load, CLKout1, CLKout2 or CLKout3 | 7 |
| Common signal output voltage | VOS | 1.125 | 1.25 | 1.375 | V | 100 Ω differential load, CLKout1, CLKout2 or CLKout3 | 7 |
| Change to VOD for complementary output states | /VOD/ | 50 | mV | 100 Ω differential load, CLKout1, CLKout2 or CLKout3 | 7 | ||
| Change to VOS for complementary output states | /VOS/ | 50 | mV | 100 Ω differential load, CLKout1, CLKout2 or CLKout3 | 7 | ||
| Output short circuit current | IOS | 24 | mA | Differential clock output pins connected to GND for CLKout1, CLKout2, or CLKout3 | 7 | ||
| Output shutdown leakage current, clock outputs | IOZ | 1 | 10 | μA | Output buffer in shutdown mode, differential clock output pins connected to VDD or GND | 7 | |
| Maximum relative frequency offset between VCXO input and H input | fOFF | -150 | 150 | ppm | Assumes H input jitter of ±15 ns | 7 | |
| Single-ended signal input voltage range | VXOin_SE | 0 | V | Single-ended input buffer mode; maximum printed as VDD | 7 | ||
| Differential signal input voltage range | VXOin_DIFF | 247 | 350 | 454 | mV | Differential input buffer mode, VCM = 1.2 V | 7 |
| Auto-format detection time | TAFD | 2 | 4 | Frames | Time from when reference input first presented to when detected as indicated by NO_REF going low. Reference timing must be stable and accurate (no missing pulses). | 6 |
CAD (KiCad official)
- Symbol:
LMH1983SQ - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: WQFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
lmh1983sq-etched.step/lmh1983sq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmh1983sq.step/lmh1983sq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (55 pp, sha256
b94fd5096487eedb, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).