main
Ray
Publish 0.1.0
460de9f
LM74930QRGERQ1
Texas Instruments · Power Distribution Switches · VQFN-24-EP(4x4)
LM74930QRGERQ1 from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DGATE | output | Diode controller gate drive output that connects to the gate of the external ideal diode MOSFET. |
| 2 | A | input | Anode of the ideal diode that connects to the source of the external ideal diode MOSFET. |
| 3 | SW | input | Voltage sensing disconnect switch terminal used as the top of the resistor ladder for the common source node, and the switch is OFF when EN is low. |
| 4 | UVLO | input | Adjustable undervoltage threshold input that is pulled HGATE low when the voltage falls below the undervoltage cut-off, and should be tied to VS or EN when unused. |
| 5 | OV | input | Adjustable overvoltage threshold input that pulls HGATE low when the sensed voltage exceeds the overvoltage cut-off, and should be tied to ground when unused. |
| 6 | EN | input | Enable input that is connected to VS for always-on operation and enters low Iq shutdown when pulled below V(ENF). |
| 7 | MODE | input | MODE input that disables the reverse current blocking function of DGATE when pulled low, and can be tied to EN or VS when unused. |
| 8 | N.C | unconnected | No connection pin that must be kept floating. |
| 9 | TMR | passive | Fault timer input where a capacitor to GND sets the fault warning, fault turn-off and retry periods, and connecting it to GND disables overcurrent protection. |
| 10 | IMON | output | Analog current monitor output that sources a scaled-down ratio of the current through RSENSE, converted to voltage by a resistor to GND. |
| 11 | ILIM | passive | Overcurrent detection setting pin where a resistor to GND sets the overcurrent comparator threshold, and connecting to GND disables overcurrent protection. |
| 12 | FLT | output | Open-drain fault output that is pulled low during undervoltage, overvoltage, overcurrent and short circuit events. |
| 13 | GND | power_in | Ground pin that connects to the system ground plane. |
| 14 | HGATE | output | GATE driver output for the HSFET that connects to the gate of the external load switch MOSFET. |
| 15 | OUT | input | Connects to the common source rail, which is the source of the external load switch MOSFET. |
| 16 | OVCLAMP | input | Overvoltage clamp input with circuit breaker (timer) functionality that connects to the OV pin, and is tied to ground when unused. |
| 17 | N.C | unconnected | No connection pin that must be kept floating. |
| 18 | ISCP | input | Short-circuit detection threshold setting pin, where connecting it to C sets an internal fixed 20 mV threshold for output short circuit detection. |
| 19 | CS- | input | Current sense negative input. |
| 20 | CS+ | input | Current sense positive input that connects through a 50-Ω resistor to the external current sense resistor. |
| 21 | N.C | unconnected | No connection pin that must be kept floating. |
| 22 | VS | power_in | Input power supply to the IC that requires a 100-nF capacitor across VS and GND. |
| 23 | CAP | output | Internal charge pump output that requires a 100-nF capacitor across CAP and VS. |
| 24 | C | input | Cathode of the ideal diode that connects to the drain of the external ideal diode MOSFET. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input pins: A to GND | -65 | 70 | V | 5 | |||
| C, VS, CS+, CS-, ISCP to GND | -1 | 70 | V | 5 | |||
| SW, EN, MODE, UVLO, OV, OVCLAMP to GND | -0.3 | 70 | V | V(A) > 0 V | 5 | ||
| RTN to GND | -65 | 0.3 | V | 5 | |||
| ISW, IFLT | -1 | 10 | mA | 5 | |||
| TMR, ILIM | -0.3 | 5.5 | V | 5 | |||
| ISCP, CS+ to CS- | -0.3 | 0.3 | V | 5 | |||
| OUT to VS | -65 | 16.5 | V | 5 | |||
| CAP to VS | -0.3 | 15 | V | 5 | |||
| CAP to A, OUT | -0.3 | 85 | V | 5 | |||
| DGATE to A | -0.3 | 15 | V | 5 | |||
| FLT to GND | -1 | 70 | V | 5 | |||
| IMON | -0.3 | 5.5 | 5 | ||||
| HGATE to OUT | -0.3 | 15 | V | 5 | |||
| Output to input pins C to A | -5 | 85 | V | 5 | |||
| Operating junction temperature | Tj | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| Input pins: A to GND (recommended) | -60 | 65 | V | 5 | |||
| VS, SW, CS+, CS-, ISCP to GND | 0 | 65 | V | 5 | |||
| EN, UVLO, OV, MODE to GND | 0 | 65 | V | 5 | |||
| External capacitance CAP to VS, VS to GND | 0.1 | µF | 5 | ||||
| External MOSFET max VGS rating DGATE to A and HGATE to OUT | 15 | V | 6 | ||||
| Operating junction temperature (recommended) | Tj | -40 | 150 | °C | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 44 | °C/W | RGE (VQFN) 24 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 38.3 | °C/W | RGE (VQFN) 24 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 21.3 | °C/W | RGE (VQFN) 24 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 5.9 | °C/W | RGE (VQFN) 24 pins | 6 | ||
| Operating input voltage | V(VS) | 4 | 65 | V | 6 | ||
| VS POR threshold, rising | V(VS_PORR) | 2.4 | 2.6 | 2.9 | V | 6 | |
| VS POR threshold, falling | V(VS_PORF) | 2.2 | 2.1 | 2.7 | V | 6 | |
| Shutdown current, I(GND) | I(SHDN) | 2.5 | 5 | µA | V(EN) = 0 V | 6 | |
| Total system quiescent current, I(GND) | I(Q) | 665 | 780 | µA | V(EN) = 2 V | 6 | |
| I(A) leakage current during reverse polarity | I(REV) | -100 | -35 | µA | 0 V ≤ V(A) ≤, 65 V | 6 | |
| Enable threshold voltage for low Iq shutdown, rising | V(ENR) | 0.8 | 1.05 | V | 6 | ||
| Enable falling threshold voltage for low Iq shutdown | V(ENF) | 0.41 | 0.7 | V | 6 | ||
| Enable input current | I(EN/UVLO) | 55 | 200 | nA | 0 V ≤ V(EN) ≤ 65 V | 6 | |
| UVLO threshold voltage, rising | V(UVLOR) | 0.585 | 0.6 | 0.63 | V | 6 | |
| UVLO threshold voltage, falling | V(UVLOF) | 0.533 | 0.55 | 0.573 | V | 7 | |
| Battery sensing disconnect switch resistance | R(SW) | 10 | 19.5 | 46 | Ω | 7 | |
| Overvoltage threshold input, rising | V(OVR) | 0.585 | 0.6 | 0.63 | V | 7 | |
| Overvoltage threshold input, falling | V(OVF) | 0.533 | 0.55 | 0.573 | V | 7 | |
| OVCLAMP threshold input, rising | V(OVCLAMPR) | 0.57 | 0.59 | 0.61 | V | 7 | |
| Input referred offset | V(OFFSET) | -2.1 | 2.1 | mV | RSET = 50Ω RIMON = 5 kΩ (corresponds to VSNS = 6 mV to 30 mV) | 7 | |
| OCP comparator rising threshold | V(SNS_TH) | 1.08 | 1.22 | 1.32 | V | 7 | |
| OCP comparator falling threshold | V(SNS_TH) | 1.02 | 1.15 | 1.25 | V | 7 | |
| ISCP SCP input bias current | 9.5 | 11 | 12 | µA | 7 | ||
| HV SCP comparator threshold | V(HV_SCP) | 17.4 | 20 | 22 | mV | VCS- > 3V | 7 |
| Current monitor output accuracy | -12.5 | 12.5 | % | VSENSE = 20 mV, RIMON = 5kΩ | 7 | ||
| LV SCP comparator threshold | V(LV_SCP) | 16.5 | 20 | 24 | mV | VCS- < 3V | 7 |
| FLT pull-down resistance | R(FLT) | 10 | 22 | 60 | Ω | 7 | |
| TMR source current during overcurrent | I(TMR_SRC_OCP) | 65 | 85 | 97 | µA | 7 | |
| Voltage at TMR pin for FLT trigger | V(TMR_FLT) | 1.04 | 1.1 | 1.2 | V | 7 | |
| Regulated forward V(A)-V(C) threshold | V(AC_REG) | 3.6 | 10.4 | 13.7 | mV | 8 | |
| V(A)-V(C) threshold for fast reverse current blocking | V(AC_REV) | -16 | -10.5 | -5 | mV | 8 | |
| V(A)-V(C) threshold for reverse to forward transition | V(AC_FWD) | 150 | 177 | 200 | mV | 8 | |
| Gate drive voltage V(DGATE)-V(A) | V(DGATE) - V(A) | 9.2 | 11.5 | 14 | V | 5 V < V(S) < 65 V | 8 |
| Gate drive voltage V(HGATE)-V(OUT) | V(HGATE) - V(OUT) | 10 | 11.1 | 14.5 | V | 5 V < V(S) < 65 V | 8 |
| HGATE source current | I(HGATE) | 39 | 55 | 75 | µA | 8 | |
| Charge pump source current | I(CAP) | 1.3 | 2.7 | mA | V(CAP), V(A) = 7 V, 6 V ≤ V(S) ≤ 65 V | 7 | |
| Charge pump turn-on voltage | 11 | 12.2 | 13.2 | V | VCAP, VS | 7 |
CAD (KiCad official)
- Symbol:
LM74930QRGERQ1 - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lm74930qrgerq1-etched.step/lm74930qrgerq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm74930qrgerq1.step/lm74930qrgerq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
d54d88498a76c31a, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM74930QRGERQ1
**Texas Instruments** · Power Distribution Switches · VQFN-24-EP(4x4)
LM74930QRGERQ1 from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DGATE | output | Diode controller gate drive output that connects to the gate of the external ideal diode MOSFET. |
| 2 | A | input | Anode of the ideal diode that connects to the source of the external ideal diode MOSFET. |
| 3 | SW | input | Voltage sensing disconnect switch terminal used as the top of the resistor ladder for the common source node, and the switch is OFF when EN is low. |
| 4 | UVLO | input | Adjustable undervoltage threshold input that is pulled HGATE low when the voltage falls below the undervoltage cut-off, and should be tied to VS or EN when unused. |
| 5 | OV | input | Adjustable overvoltage threshold input that pulls HGATE low when the sensed voltage exceeds the overvoltage cut-off, and should be tied to ground when unused. |
| 6 | EN | input | Enable input that is connected to VS for always-on operation and enters low Iq shutdown when pulled below V(ENF). |
| 7 | MODE | input | MODE input that disables the reverse current blocking function of DGATE when pulled low, and can be tied to EN or VS when unused. |
| 8 | N.C | unconnected | No connection pin that must be kept floating. |
| 9 | TMR | passive | Fault timer input where a capacitor to GND sets the fault warning, fault turn-off and retry periods, and connecting it to GND disables overcurrent protection. |
| 10 | IMON | output | Analog current monitor output that sources a scaled-down ratio of the current through RSENSE, converted to voltage by a resistor to GND. |
| 11 | ILIM | passive | Overcurrent detection setting pin where a resistor to GND sets the overcurrent comparator threshold, and connecting to GND disables overcurrent protection. |
| 12 | FLT | output | Open-drain fault output that is pulled low during undervoltage, overvoltage, overcurrent and short circuit events. |
| 13 | GND | power_in | Ground pin that connects to the system ground plane. |
| 14 | HGATE | output | GATE driver output for the HSFET that connects to the gate of the external load switch MOSFET. |
| 15 | OUT | input | Connects to the common source rail, which is the source of the external load switch MOSFET. |
| 16 | OVCLAMP | input | Overvoltage clamp input with circuit breaker (timer) functionality that connects to the OV pin, and is tied to ground when unused. |
| 17 | N.C | unconnected | No connection pin that must be kept floating. |
| 18 | ISCP | input | Short-circuit detection threshold setting pin, where connecting it to C sets an internal fixed 20 mV threshold for output short circuit detection. |
| 19 | CS- | input | Current sense negative input. |
| 20 | CS+ | input | Current sense positive input that connects through a 50-Ω resistor to the external current sense resistor. |
| 21 | N.C | unconnected | No connection pin that must be kept floating. |
| 22 | VS | power_in | Input power supply to the IC that requires a 100-nF capacitor across VS and GND. |
| 23 | CAP | output | Internal charge pump output that requires a 100-nF capacitor across CAP and VS. |
| 24 | C | input | Cathode of the ideal diode that connects to the drain of the external ideal diode MOSFET. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input pins: A to GND | | -65 | | 70 | V | | 5 |
| C, VS, CS+, CS-, ISCP to GND | | -1 | | 70 | V | | 5 |
| SW, EN, MODE, UVLO, OV, OVCLAMP to GND | | -0.3 | | 70 | V | V(A) > 0 V | 5 |
| RTN to GND | | -65 | | 0.3 | V | | 5 |
| ISW, IFLT | | -1 | | 10 | mA | | 5 |
| TMR, ILIM | | -0.3 | | 5.5 | V | | 5 |
| ISCP, CS+ to CS- | | -0.3 | | 0.3 | V | | 5 |
| OUT to VS | | -65 | | 16.5 | V | | 5 |
| CAP to VS | | -0.3 | | 15 | V | | 5 |
| CAP to A, OUT | | -0.3 | | 85 | V | | 5 |
| DGATE to A | | -0.3 | | 15 | V | | 5 |
| FLT to GND | | -1 | | 70 | V | | 5 |
| IMON | | -0.3 | | 5.5 | | | 5 |
| HGATE to OUT | | -0.3 | | 15 | V | | 5 |
| Output to input pins C to A | | -5 | | 85 | V | | 5 |
| Operating junction temperature | Tj | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -40 | | 150 | °C | | 5 |
| Input pins: A to GND (recommended) | | -60 | | 65 | V | | 5 |
| VS, SW, CS+, CS-, ISCP to GND | | 0 | | 65 | V | | 5 |
| EN, UVLO, OV, MODE to GND | | 0 | | 65 | V | | 5 |
| External capacitance CAP to VS, VS to GND | | 0.1 | | | µF | | 5 |
| External MOSFET max VGS rating DGATE to A and HGATE to OUT | | | | 15 | V | | 6 |
| Operating junction temperature (recommended) | Tj | -40 | | 150 | °C | | 6 |
| Junction-to-ambient thermal resistance | RθJA | | 44 | | °C/W | RGE (VQFN) 24 pins | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 38.3 | | °C/W | RGE (VQFN) 24 pins | 6 |
| Junction-to-board thermal resistance | RθJB | | 21.3 | | °C/W | RGE (VQFN) 24 pins | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 5.9 | | °C/W | RGE (VQFN) 24 pins | 6 |
| Operating input voltage | V(VS) | 4 | | 65 | V | | 6 |
| VS POR threshold, rising | V(VS_PORR) | 2.4 | 2.6 | 2.9 | V | | 6 |
| VS POR threshold, falling | V(VS_PORF) | 2.2 | 2.1 | 2.7 | V | | 6 |
| Shutdown current, I(GND) | I(SHDN) | | 2.5 | 5 | µA | V(EN) = 0 V | 6 |
| Total system quiescent current, I(GND) | I(Q) | | 665 | 780 | µA | V(EN) = 2 V | 6 |
| I(A) leakage current during reverse polarity | I(REV) | -100 | | -35 | µA | 0 V ≤ V(A) ≤, 65 V | 6 |
| Enable threshold voltage for low Iq shutdown, rising | V(ENR) | 0.8 | | 1.05 | V | | 6 |
| Enable falling threshold voltage for low Iq shutdown | V(ENF) | 0.41 | | 0.7 | V | | 6 |
| Enable input current | I(EN/UVLO) | 55 | | 200 | nA | 0 V ≤ V(EN) ≤ 65 V | 6 |
| UVLO threshold voltage, rising | V(UVLOR) | 0.585 | 0.6 | 0.63 | V | | 6 |
| UVLO threshold voltage, falling | V(UVLOF) | 0.533 | 0.55 | 0.573 | V | | 7 |
| Battery sensing disconnect switch resistance | R(SW) | 10 | 19.5 | 46 | Ω | | 7 |
| Overvoltage threshold input, rising | V(OVR) | 0.585 | 0.6 | 0.63 | V | | 7 |
| Overvoltage threshold input, falling | V(OVF) | 0.533 | 0.55 | 0.573 | V | | 7 |
| OVCLAMP threshold input, rising | V(OVCLAMPR) | 0.57 | 0.59 | 0.61 | V | | 7 |
| Input referred offset | V(OFFSET) | -2.1 | | 2.1 | mV | RSET = 50Ω RIMON = 5 kΩ (corresponds to VSNS = 6 mV to 30 mV) | 7 |
| OCP comparator rising threshold | V(SNS_TH) | 1.08 | 1.22 | 1.32 | V | | 7 |
| OCP comparator falling threshold | V(SNS_TH) | 1.02 | 1.15 | 1.25 | V | | 7 |
| ISCP SCP input bias current | | 9.5 | 11 | 12 | µA | | 7 |
| HV SCP comparator threshold | V(HV_SCP) | 17.4 | 20 | 22 | mV | VCS- > 3V | 7 |
| Current monitor output accuracy | | -12.5 | | 12.5 | % | VSENSE = 20 mV, RIMON = 5kΩ | 7 |
| LV SCP comparator threshold | V(LV_SCP) | 16.5 | 20 | 24 | mV | VCS- < 3V | 7 |
| FLT pull-down resistance | R(FLT) | 10 | 22 | 60 | Ω | | 7 |
| TMR source current during overcurrent | I(TMR_SRC_OCP) | 65 | 85 | 97 | µA | | 7 |
| Voltage at TMR pin for FLT trigger | V(TMR_FLT) | 1.04 | 1.1 | 1.2 | V | | 7 |
| Regulated forward V(A)-V(C) threshold | V(AC_REG) | 3.6 | 10.4 | 13.7 | mV | | 8 |
| V(A)-V(C) threshold for fast reverse current blocking | V(AC_REV) | -16 | -10.5 | -5 | mV | | 8 |
| V(A)-V(C) threshold for reverse to forward transition | V(AC_FWD) | 150 | 177 | 200 | mV | | 8 |
| Gate drive voltage V(DGATE)-V(A) | V(DGATE) - V(A) | 9.2 | 11.5 | 14 | V | 5 V < V(S) < 65 V | 8 |
| Gate drive voltage V(HGATE)-V(OUT) | V(HGATE) - V(OUT) | 10 | 11.1 | 14.5 | V | 5 V < V(S) < 65 V | 8 |
| HGATE source current | I(HGATE) | 39 | 55 | 75 | µA | | 8 |
| Charge pump source current | I(CAP) | 1.3 | | 2.7 | mA | V(CAP), V(A) = 7 V, 6 V ≤ V(S) ≤ 65 V | 7 |
| Charge pump turn-on voltage | | 11 | 12.2 | 13.2 | V | VCAP, VS | 7 |
## CAD (KiCad official)
- Symbol: `LM74930QRGERQ1`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `lm74930qrgerq1-etched.step` / `lm74930qrgerq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm74930qrgerq1.step` / `lm74930qrgerq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm74930-q1.pdf) (42 pp, sha256 `d54d88498a76c31a`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm74930qrgerq1-datasheet.pdf)