← Commit history

Initial commit: component/lm74910qrgerq1

Ray ·3bfe5432b1 ·
2 files changed +308
README.mdadded+62
@@ -0,0 +1,62 @@+# LM74910QRGERQ1++**Texas Instruments** · Power Distribution Switches · VQFN-24-EP(4x4)++LM74910QRGERQ1 from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | DGATE | output | Diode controller gate-drive output that connects to the gate of the external ideal-diode MOSFET. |+| 2 | A | input | Anode of the ideal diode; connects to the source of the external MOSFET (Q1) and is monitored for the AC-DC forward regulation and fast reverse-voltage comparator. |+| 3 | SW | input | Voltage-sense disconnect switch terminal internally connected to VSNS; used as the top connection for the battery-detect or OV resistor ladder and disconnects when EN is pulled low; short to VS if the internal switch is unused. |+| 4 | UVLO | input | Adjustable undervoltage threshold input; a resistor divider from SW to UVLO to GND sets the UVLO falling threshold that pulls HGATE low to turn off the HSFET. |+| 5 | OV | input | Adjustable overvoltage threshold input; a resistor divider from SW to OV sets the OV cutoff threshold that pulls HGATE low to turn off the HSFET. |+| 6 | EN | input | Enable input, typically tied to VS for always-on operation or driven externally; pulling it below V(ENF) places the device in the low-IQ shutdown mode. |+| 7 | SLEEP | input | Active-low sleep-mode input driven by a microcontroller; pulling it low turns off the charge pump and gate drivers and powers the output through an internal current-limited bypass switch. |+| 8 | NC | unconnected | No internal connection. |+| 9 | TMR | input | Fault timer input; a capacitor from TMR to GND sets the overcurrent-warning, fault (FLT), and retry timing, leaving it open sets the fastest timing, and tying it to GND disables overcurrent protection. |+| 10 | IMON | output | Analog current-monitor output that sources a scaled current through the external RSNS sense resistor; an external resistor to GND converts this current to a proportional voltage, and the pin should float if unused. |+| 11 | ILIM | input | Overcurrent detection set pin; a resistor from ILIM to GND sets the overcurrent comparator threshold, and ILIM should be tied to GND if overcurrent protection is not needed. |+| 12 | FLT | output | Open-drain fault output that is pulled low during a UVLO, OV, OCP, or SCP event. |+| 13 | GND | power_in | Ground connection to the system ground plane. |+| 14 | HGATE | output | Gate-drive output for the load-disconnect HSFET; connects to the gate of the external MOSFET (Q2). |+| 15 | OUT | input | Connection to the output power rail (external MOSFET source) used to sense the output voltage for load-disconnect control. |+| 16 | SLEEP_OV | input | Sleep-mode overvoltage protection pin; connect to VS for OV cutoff behavior or to OUT for OV clamp behavior during sleep mode. |+| 17 | NC | unconnected | No internal connection. |+| 18 | ISCP | input | Short-circuit detection threshold set pin; leave floating if short-circuit protection is not needed, or tie to CS+ to set the internal fixed 20 mV threshold. |+| 19 | CS- | input | Negative input of the current-sense amplifier. |+| 20 | CS+ | input | Positive input of the current-sense amplifier; connect a 50 to 100 mΩ resistor between CS+ and the external current-sense resistor. |+| 21 | NC | unconnected | No internal connection. |+| 22 | VS | power_in | IC input power supply; connect VS to the mid-point of the common-drain back-to-back MOSFET configuration and place a 100 nF capacitor between VS and GND. |+| 23 | CAP | output | Charge-pump output; place a 100 nF capacitor between CAP and VS to supply the gate-drive charge pump. |+| 24 | C | input | Cathode of the ideal diode; connects to the drain of the external MOSFET (Q1). |+| 25 | RTN | unconnected | Exposed thermal pad; keep it floating and do not connect it to the GND plane. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `LM74910QRGERQ1`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `lm74910qrgerq1-etched.step` / `lm74910qrgerq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm74910qrgerq1.step` / `lm74910qrgerq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com.cn/cn/lit/ds/symlink/lm74910-q1.pdf?ts=1739432271354&ref_url=https%253A%252F%252Fwww.ti.com.cn%252Fsitesearch%252Fzh-cn%252Fdocs%252Funiversalsearch.tsp%253FlangPref%253Dzh-CN%2526nr%253D8%2526searchTerm%253DLM74910QRGERQ1) (50 pp, sha256 `0dec8e92d6d855bd`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm74910qrgerq1-datasheet.pdf)
page.jsonadded+246
@@ -0,0 +1,246 @@+{+  "slug": "lm74910qrgerq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Power Distribution Switches, VQFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "lm74910qrgerq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm74910qrgerq1.kicad_sym",+    "lm74910qrgerq1.kicad_mod",+    "lm74910qrgerq1.glb",+    "lm74910qrgerq1.step",+    "lm74910qrgerq1.lbr",+    "docs/hero.png",+    "docs/lm74910qrgerq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM74910QRGERQ1",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "Power Distribution Switches",+    "datasheet": "https://www.ti.com.cn/cn/lit/ds/symlink/lm74910-q1.pdf?ts=1739432271354&ref_url=https%253A%252F%252Fwww.ti.com.cn%252Fsitesearch%252Fzh-cn%252Fdocs%252Funiversalsearch.tsp%253FlangPref%253Dzh-CN%2526nr%253D8%2526searchTerm%253DLM74910QRGERQ1",+    "parts": {+      "symbol": "lm74910qrgerq1.kicad_sym",+      "footprint": "lm74910qrgerq1.kicad_mod",+      "model_3d": "lm74910qrgerq1-etched.glb",+      "model_3d_plain": "lm74910qrgerq1.glb",+      "model_3d_step": "lm74910qrgerq1-etched.step",+      "model_3d_step_plain": "lm74910qrgerq1.step",+      "lbr": "lm74910qrgerq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C22427891"+    },+    "pins": [+      {+        "number": "1",+        "name": "DGATE",+        "type": "output",+        "description": "Diode controller gate-drive output that connects to the gate of the external ideal-diode MOSFET."+      },+      {+        "number": "2",+        "name": "A",+        "type": "input",+        "description": "Anode of the ideal diode; connects to the source of the external MOSFET (Q1) and is monitored for the AC-DC forward regulation and fast reverse-voltage comparator."+      },+      {+        "number": "3",+        "name": "SW",+        "type": "input",+        "description": "Voltage-sense disconnect switch terminal internally connected to VSNS; used as the top connection for the battery-detect or OV resistor ladder and disconnects when EN is pulled low; short to VS if the internal switch is unused."+      },+      {+        "number": "4",+        "name": "UVLO",+        "type": "input",+        "description": "Adjustable undervoltage threshold input; a resistor divider from SW to UVLO to GND sets the UVLO falling threshold that pulls HGATE low to turn off the HSFET."+      },+      {+        "number": "5",+        "name": "OV",+        "type": "input",+        "description": "Adjustable overvoltage threshold input; a resistor divider from SW to OV sets the OV cutoff threshold that pulls HGATE low to turn off the HSFET."+      },+      {+        "number": "6",+        "name": "EN",+        "type": "input",+        "description": "Enable input, typically tied to VS for always-on operation or driven externally; pulling it below V(ENF) places the device in the low-IQ shutdown mode."+      },+      {+        "number": "7",+        "name": "SLEEP",+        "type": "input",+        "description": "Active-low sleep-mode input driven by a microcontroller; pulling it low turns off the charge pump and gate drivers and powers the output through an internal current-limited bypass switch."+      },+      {+        "number": "8",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection."+      },+      {+        "number": "9",+        "name": "TMR",+        "type": "input",+        "description": "Fault timer input; a capacitor from TMR to GND sets the overcurrent-warning, fault (FLT), and retry timing, leaving it open sets the fastest timing, and tying it to GND disables overcurrent protection."+      },+      {+        "number": "10",+        "name": "IMON",+        "type": "output",+        "description": "Analog current-monitor output that sources a scaled current through the external RSNS sense resistor; an external resistor to GND converts this current to a proportional voltage, and the pin should float if unused."+      },+      {+        "number": "11",+        "name": "ILIM",+        "type": "input",+        "description": "Overcurrent detection set pin; a resistor from ILIM to GND sets the overcurrent comparator threshold, and ILIM should be tied to GND if overcurrent protection is not needed."+      },+      {+        "number": "12",+        "name": "FLT",+        "type": "output",+        "description": "Open-drain fault output that is pulled low during a UVLO, OV, OCP, or SCP event."+      },+      {+        "number": "13",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection to the system ground plane."+      },+      {+        "number": "14",+        "name": "HGATE",+        "type": "output",+        "description": "Gate-drive output for the load-disconnect HSFET; connects to the gate of the external MOSFET (Q2)."+      },+      {+        "number": "15",+        "name": "OUT",+        "type": "input",+        "description": "Connection to the output power rail (external MOSFET source) used to sense the output voltage for load-disconnect control."+      },+      {+        "number": "16",+        "name": "SLEEP_OV",+        "type": "input",+        "description": "Sleep-mode overvoltage protection pin; connect to VS for OV cutoff behavior or to OUT for OV clamp behavior during sleep mode."+      },+      {+        "number": "17",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection."+      },+      {+        "number": "18",+        "name": "ISCP",+        "type": "input",+        "description": "Short-circuit detection threshold set pin; leave floating if short-circuit protection is not needed, or tie to CS+ to set the internal fixed 20 mV threshold."+      },+      {+        "number": "19",+        "name": "CS-",+        "type": "input",+        "description": "Negative input of the current-sense amplifier."+      },+      {+        "number": "20",+        "name": "CS+",+        "type": "input",+        "description": "Positive input of the current-sense amplifier; connect a 50 to 100 mΩ resistor between CS+ and the external current-sense resistor."+      },+      {+        "number": "21",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection."+      },+      {+        "number": "22",+        "name": "VS",+        "type": "power_in",+        "description": "IC input power supply; connect VS to the mid-point of the common-drain back-to-back MOSFET configuration and place a 100 nF capacitor between VS and GND."+      },+      {+        "number": "23",+        "name": "CAP",+        "type": "output",+        "description": "Charge-pump output; place a 100 nF capacitor between CAP and VS to supply the gate-drive charge pump."+      },+      {+        "number": "24",+        "name": "C",+        "type": "input",+        "description": "Cathode of the ideal diode; connects to the drain of the external MOSFET (Q1)."+      },+      {+        "number": "25",+        "name": "RTN",+        "type": "unconnected",+        "description": "Exposed thermal pad; keep it floating and do not connect it to the GND plane."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Thermal pad (RTN) is exposed on bottom and must be soldered to PCB but kept floating from GND plane ",+          "exposed pad 25 added from the footprint"+        ],+        "pages_sent": 50,+        "cost_usd": 0.5367,+        "at": "2026-09-23T03:05:20"+      },+      "datasheet": {+        "url": "https://www.ti.com.cn/cn/lit/ds/symlink/lm74910-q1.pdf?ts=1739432271354&ref_url=https%253A%252F%252Fwww.ti.com.cn%252Fsitesearch%252Fzh-cn%252Fdocs%252Funiversalsearch.tsp%253FlangPref%253Dzh-CN%2526nr%253D8%2526searchTerm%253DLM74910QRGERQ1",+        "pages": 50,+        "sha256": "0dec8e92d6d855bd",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file