main
Ray
Publish 0.1.0
62fb8bd
LM63610DQPWPRQ1
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM63610DQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Regulator switching node that connects to the power inductor; SW to PGND is rated -6 V to 40 V for transients under 10 ns in the HTSSOP package. |
| 2 | SW | power_out | Second switching node pin, tied to pin 1, that connects to the power inductor. |
| 3 | CBOOT | power_in | Bootstrap supply for the internal high-side driver; connect a 220nF quality capacitor between this pin and SW, with BOOT to SW rated -0.3 V to 5.5 V. |
| 4 | VCC | power_out | Internal 5 V LDO output that powers the internal control circuits; do not connect external loads, and place a 1µF quality capacitor between this pin and PGND. |
| 5 | RT | input | Switching-frequency programming input: tie to VCC for 400kHz, to AGND for 2.1MHz, or to a timing resistor for 250kHz to 2200kHz; it must not float and is rated 0 V to 5 V. |
| 6 | VSEL | input | Output-voltage select input: tie to VCC for 5 V, to AGND for 3.3 V, or to AGND through 10kΩ for an adjustable output; it must not float and is rated 0 V to 5 V. |
| 7 | SYNC/MODE | input | Mode selection and synchronization input: tie to VCC for FPWM, to AGND for automatic mode, or drive with an external clock (250kHz to 2200kHz); it is rated 0 V to 5 V. |
| 8 | RESET | output | Open-drain power-good flag that needs an external pull-up to a suitable supply, reads high for power good and low for fault, is forced low when EN is low, and may be left open if unused; RESET to AGND is rated -0.3 V to 16 V. |
| 9 | FB | input | Feedback input that connects to the output for fixed 5 V or 3.3 V operation or to a divider tap for adjustable operation (regulated to 1 V); it must not float or be grounded. |
| 10 | AGND | power_in | Analog ground and logic reference for the regulator and system; all electrical parameters are measured relative to this pin. |
| 11 | EN | input | Enable input with precision thresholds (VEN-H 1.425 V to 1.575 V rising, VEN-L 0.9 V to 0.94 V falling); it may connect directly to VIN but must not float. |
| 12 | VIN | power_in | Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND, with a 220nF capacitor within 1 mm of the VIN and PGND pins. |
| 13 | VIN | power_in | Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND. |
| 14 | NC | unconnected | No internal connection to the device circuitry. |
| 15 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors. |
| 16 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors. |
| 17 | DAP | power_in | Exposed die-attach pad for electrical ground and heat sinking; solder directly to the system ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN 至 PGND(HTSSOP 封装) | -0.3 | 40 | V | 6 | |||
| EN 至 AGND(HTSSOP 封装) | -0.3 | 40 | V | 6 | |||
| SYNC/MODE 到 AGND | -0.3 | 6 | V | 6 | |||
| VSEL 和 RT 至 AGND | -0.3 | 5.5 | V | 6 | |||
| RESET 至 AGND | -0.3 | 16 | V | 6 | |||
| FB 至 AGND(固定 VOUT 模式) | -0.3 | 16 | V | 6 | |||
| FB 至 AGND(可调 VOUT 模式) | -0.3 | 5.5 | V | 6 | |||
| AGND 到 PGND | -0.3 | 0.3 | V | 6 | |||
| SW 至 PGND,瞬变时间不到 10ns(HTSSOP 封装) | -6 | 40 | V | 6 | |||
| BOOT 至 SW | -0.3 | 5.5 | V | 6 | |||
| VCC 到 AGND | VCC | -0.3 | 5.5 | V | 6 | ||
| 结温 TJ | TJ | -40 | 150 | °C | 6 | ||
| 贮存温度 Tstg | Tstg | -65 | 150 | °C | 6 | ||
| SYNC/MODE、VSEL 和 RT 至 AGND | 0 | 5 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 | ||
| RESET | 0 | 5 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 | ||
| VOUT | VOUT | 1 | 20 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 | |
| VCC | VCC | 2.7 | 5.25 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 | |
| IOUT,LM63610 | IOUT | 0 | 1 | A | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 | |
| VIN 最小工作输入电压 | 3.5 | V | 8 | ||||
| 非开关输入电流 IQ(在 VIN 引脚处测得) | IQ | 23 | 40 | µA | VEN = 3.3V,VFB = 1.2× 稳压值 | 8 | |
| 关断静态电流 ISD(在 VIN 引脚处测得) | ISD | 5.3 | 10 | µA | VEN = 0V | 8 | |
| 最小工作电压阈值 下降 VIN | VUVLO_F | 2.6 | 3 | V | 下降 VIN,IVCC = 0A | 8 | |
| 触发 OVP 时 SW 上的下拉电流 | IPOR | 0.5 | 1.5 | 2.5 | mA | VEN = 0V、VSW = 5V | 8 |
| VOUT 的精密使能高电平 | VEN-H | 1.425 | 1.5 | 1.575 | V | VEN 上升 | 8 |
| VOUT 的精密使能低电平 | VEN-L | 0.9 | 0.94 | V | VEN 下降 | 8 | |
| 使能输入漏电流 | ILKG-EN | -100 | 0.2 | 300 | nA | VEN = 13.5V | 8 |
| 用于在启动时选择有效可调输出电压的电阻器范围 | RSEL-ADJ | 8 | 50 | kΩ | 8 | ||
| 内部 VCC 电压 | VCC | 4.75 | 5 | 5.25 | V | 6V ≤ VIN ≤ 最大工作 VIN | 8 |
| VCC 钳位电压 | VCCM | 5.25 | 5.55 | 5.8 | V | 向 VCC 提供 1mA | 8 |
| 反馈电压(可调) | VFB_ADJ | 0.985 | 1 | 1.015 | V | VIN = 3.5 - 最大工作 VIN | 8 |
| 反馈电压(5V) | VFB_5V | 4.925 | 5 | 5.075 | V | VIN = 5.5 - 最大工作 VIN | 8 |
| 反馈电压(3.3V) | VFB_3p3V | 3.25 | 3.3 | 3.35 | V | VIN = 3.8 - 最大工作 VIN | 8 |
| FB 引脚上的输入漏电流(可调) | IFB_ADJ | 0.2 | 100 | nA | FB = 1V | 8 | |
| FB 引脚上的输入漏电流(5V) | IFB_5V | 2.89 | 3.4 | µA | FB = 5V | 8 | |
| FB 引脚上的输入漏电流(3.3V) | IFB_3p3V | 1.67 | 2 | µA | FB = 3.3V | 8 | |
| ISC 短路高侧电流限值 | ISC | 1.9 | 2.25 | 2.7 | A | 1A 版本 | 8 |
| 低侧电流限值 | ILS-LIMIT | 1.5 | 1.8 | 2.12 | A | 8 | |
| 最小峰值电感器电流 | IPEAK-MIN | 0.375 | 0.7 | A | 8 | ||
| 负电流限值 | IL-NEG | -1.49 | -1.2 | -0.75 | A | 8 | |
| FB 引脚上的断续阈值 | VHICCUP | 37 | 42 | 47 | % | 8 | |
| RESET 阈值上限 - 上升 FB 电压 | VRESET-HIGH | 110 | 112 | 115 | % | 8 | |
| RESET 阈值下限 - 下降 FB 电压 | VRESET-LOW | 91 | 93 | 95 | % | 8 | |
| RESET 迟滞 FB 电压 | VRESET-HYS | 1.1 | 1.8 | 2.5 | % | 8 | |
| 正常 PG 功能的最小输入电压 | V_RESET_VALID | 0.7 | 1.04 | 1.25 | V | 在 VRESET 小于 0.4V 且通过 10kΩ 上拉至外部 5V 的情况下测得 | 8 |
| RESET 导通电阻 | RRESET | 60 | 150 | Ω | VEN = 5V,1mA 上拉电流 | 8 | |
| RESET 导通电阻 | RRESET | 40 | 125 | Ω | VEN = 0V,1mA 上拉电流 | 9 | |
| 同步输入和模式高电平阈值 | VSYNC-HIGH | 1.5 | 1.8 | V | 9 | ||
| 同步输入和模式低电平阈值 | VSYNC-LOW | 0.8 | 1.15 | V | 9 | ||
| 过流断续重试延迟时间 | tOC | 70 | 104 | 140 | ms | 10 | |
| 内部软启动时间 | tSS | 1 | 1.6 | 2.2 | ms | 10 | |
| RESET 边沿抗尖峰延迟 | tdg | 10 | 17 | 30 | µs | 10 | |
| RESET 运行时间 | tRISE-DELAY | 2 | 3 | 5 | ms | FB 时间在 RESET 释放前必须有效。 | 10 |
| MOSFET 高侧导通电阻 | RDS-ON-HS | 93 | mΩ | 负载 = 1A | 9 | ||
| MOSFET 低侧导通电阻 | RDS-ON-LS | 61 | mΩ | 负载 = 1A | 9 | ||
| 结至环境热阻 | RθJA | 43.1 | °C/W | JESD 51-7,4层JEDEC板仿真 | 7 | ||
| 结至外壳(顶部)热阻 | RθJC(top) | 35.4 | °C/W | 7 | |||
| 结至电路板热阻 | RθJB | 18.5 | °C/W | 7 | |||
| 结至顶部特征参数 | ΨJT | 0.9 | °C/W | 7 | |||
| 结至电路板特征参数 | ΨJB | 18.5 | °C/W | 7 | |||
| 结至外壳(底部)热阻 | RθJC(bot) | 4.5 | °C/W | 7 |
CAD (KiCad official)
- Symbol:
LM63610DQPWPRQ1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm63610dqpwprq1-etched.step/lm63610dqpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm63610dqpwprq1.step/lm63610dqpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
973de5edc4caace0, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM63610DQPWPRQ1
**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP
LM63610DQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Regulator switching node that connects to the power inductor; SW to PGND is rated -6 V to 40 V for transients under 10 ns in the HTSSOP package. |
| 2 | SW | power_out | Second switching node pin, tied to pin 1, that connects to the power inductor. |
| 3 | CBOOT | power_in | Bootstrap supply for the internal high-side driver; connect a 220nF quality capacitor between this pin and SW, with BOOT to SW rated -0.3 V to 5.5 V. |
| 4 | VCC | power_out | Internal 5 V LDO output that powers the internal control circuits; do not connect external loads, and place a 1µF quality capacitor between this pin and PGND. |
| 5 | RT | input | Switching-frequency programming input: tie to VCC for 400kHz, to AGND for 2.1MHz, or to a timing resistor for 250kHz to 2200kHz; it must not float and is rated 0 V to 5 V. |
| 6 | VSEL | input | Output-voltage select input: tie to VCC for 5 V, to AGND for 3.3 V, or to AGND through 10kΩ for an adjustable output; it must not float and is rated 0 V to 5 V. |
| 7 | SYNC/MODE | input | Mode selection and synchronization input: tie to VCC for FPWM, to AGND for automatic mode, or drive with an external clock (250kHz to 2200kHz); it is rated 0 V to 5 V. |
| 8 | RESET | output | Open-drain power-good flag that needs an external pull-up to a suitable supply, reads high for power good and low for fault, is forced low when EN is low, and may be left open if unused; RESET to AGND is rated -0.3 V to 16 V. |
| 9 | FB | input | Feedback input that connects to the output for fixed 5 V or 3.3 V operation or to a divider tap for adjustable operation (regulated to 1 V); it must not float or be grounded. |
| 10 | AGND | power_in | Analog ground and logic reference for the regulator and system; all electrical parameters are measured relative to this pin. |
| 11 | EN | input | Enable input with precision thresholds (VEN-H 1.425 V to 1.575 V rising, VEN-L 0.9 V to 0.94 V falling); it may connect directly to VIN but must not float. |
| 12 | VIN | power_in | Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND, with a 220nF capacitor within 1 mm of the VIN and PGND pins. |
| 13 | VIN | power_in | Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND. |
| 14 | NC | unconnected | No internal connection to the device circuitry. |
| 15 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors. |
| 16 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors. |
| 17 | DAP | power_in | Exposed die-attach pad for electrical ground and heat sinking; solder directly to the system ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN 至 PGND(HTSSOP 封装) | | -0.3 | | 40 | V | | 6 |
| EN 至 AGND(HTSSOP 封装) | | -0.3 | | 40 | V | | 6 |
| SYNC/MODE 到 AGND | | -0.3 | | 6 | V | | 6 |
| VSEL 和 RT 至 AGND | | -0.3 | | 5.5 | V | | 6 |
| RESET 至 AGND | | -0.3 | | 16 | V | | 6 |
| FB 至 AGND(固定 VOUT 模式) | | -0.3 | | 16 | V | | 6 |
| FB 至 AGND(可调 VOUT 模式) | | -0.3 | | 5.5 | V | | 6 |
| AGND 到 PGND | | -0.3 | | 0.3 | V | | 6 |
| SW 至 PGND,瞬变时间不到 10ns(HTSSOP 封装) | | -6 | | 40 | V | | 6 |
| BOOT 至 SW | | -0.3 | | 5.5 | V | | 6 |
| VCC 到 AGND | VCC | -0.3 | | 5.5 | V | | 6 |
| 结温 TJ | TJ | -40 | | 150 | °C | | 6 |
| 贮存温度 Tstg | Tstg | -65 | | 150 | °C | | 6 |
| SYNC/MODE、VSEL 和 RT 至 AGND | | 0 | | 5 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 |
| RESET | | 0 | | 5 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 |
| VOUT | VOUT | 1 | | 20 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 |
| VCC | VCC | 2.7 | | 5.25 | V | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 |
| IOUT,LM63610 | IOUT | 0 | | 1 | A | 在建议的 -40°C 到 150°C 结温范围内测得 | 6 |
| VIN 最小工作输入电压 | | 3.5 | | | V | | 8 |
| 非开关输入电流 IQ(在 VIN 引脚处测得) | IQ | | 23 | 40 | µA | VEN = 3.3V,VFB = 1.2× 稳压值 | 8 |
| 关断静态电流 ISD(在 VIN 引脚处测得) | ISD | | 5.3 | 10 | µA | VEN = 0V | 8 |
| 最小工作电压阈值 下降 VIN | VUVLO_F | | 2.6 | 3 | V | 下降 VIN,IVCC = 0A | 8 |
| 触发 OVP 时 SW 上的下拉电流 | IPOR | 0.5 | 1.5 | 2.5 | mA | VEN = 0V、VSW = 5V | 8 |
| VOUT 的精密使能高电平 | VEN-H | 1.425 | 1.5 | 1.575 | V | VEN 上升 | 8 |
| VOUT 的精密使能低电平 | VEN-L | | 0.9 | 0.94 | V | VEN 下降 | 8 |
| 使能输入漏电流 | ILKG-EN | -100 | 0.2 | 300 | nA | VEN = 13.5V | 8 |
| 用于在启动时选择有效可调输出电压的电阻器范围 | RSEL-ADJ | 8 | | 50 | kΩ | | 8 |
| 内部 VCC 电压 | VCC | 4.75 | 5 | 5.25 | V | 6V ≤ VIN ≤ 最大工作 VIN | 8 |
| VCC 钳位电压 | VCCM | 5.25 | 5.55 | 5.8 | V | 向 VCC 提供 1mA | 8 |
| 反馈电压(可调) | VFB_ADJ | 0.985 | 1 | 1.015 | V | VIN = 3.5 - 最大工作 VIN | 8 |
| 反馈电压(5V) | VFB_5V | 4.925 | 5 | 5.075 | V | VIN = 5.5 - 最大工作 VIN | 8 |
| 反馈电压(3.3V) | VFB_3p3V | 3.25 | 3.3 | 3.35 | V | VIN = 3.8 - 最大工作 VIN | 8 |
| FB 引脚上的输入漏电流(可调) | IFB_ADJ | | 0.2 | 100 | nA | FB = 1V | 8 |
| FB 引脚上的输入漏电流(5V) | IFB_5V | | 2.89 | 3.4 | µA | FB = 5V | 8 |
| FB 引脚上的输入漏电流(3.3V) | IFB_3p3V | | 1.67 | 2 | µA | FB = 3.3V | 8 |
| ISC 短路高侧电流限值 | ISC | 1.9 | 2.25 | 2.7 | A | 1A 版本 | 8 |
| 低侧电流限值 | ILS-LIMIT | 1.5 | 1.8 | 2.12 | A | | 8 |
| 最小峰值电感器电流 | IPEAK-MIN | | 0.375 | 0.7 | A | | 8 |
| 负电流限值 | IL-NEG | -1.49 | -1.2 | -0.75 | A | | 8 |
| FB 引脚上的断续阈值 | VHICCUP | 37 | 42 | 47 | % | | 8 |
| RESET 阈值上限 - 上升 FB 电压 | VRESET-HIGH | 110 | 112 | 115 | % | | 8 |
| RESET 阈值下限 - 下降 FB 电压 | VRESET-LOW | 91 | 93 | 95 | % | | 8 |
| RESET 迟滞 FB 电压 | VRESET-HYS | 1.1 | 1.8 | 2.5 | % | | 8 |
| 正常 PG 功能的最小输入电压 | V_RESET_VALID | 0.7 | 1.04 | 1.25 | V | 在 VRESET 小于 0.4V 且通过 10kΩ 上拉至外部 5V 的情况下测得 | 8 |
| RESET 导通电阻 | RRESET | | 60 | 150 | Ω | VEN = 5V,1mA 上拉电流 | 8 |
| RESET 导通电阻 | RRESET | | 40 | 125 | Ω | VEN = 0V,1mA 上拉电流 | 9 |
| 同步输入和模式高电平阈值 | VSYNC-HIGH | | 1.5 | 1.8 | V | | 9 |
| 同步输入和模式低电平阈值 | VSYNC-LOW | | 0.8 | 1.15 | V | | 9 |
| 过流断续重试延迟时间 | tOC | 70 | 104 | 140 | ms | | 10 |
| 内部软启动时间 | tSS | 1 | 1.6 | 2.2 | ms | | 10 |
| RESET 边沿抗尖峰延迟 | tdg | 10 | 17 | 30 | µs | | 10 |
| RESET 运行时间 | tRISE-DELAY | 2 | 3 | 5 | ms | FB 时间在 RESET 释放前必须有效。 | 10 |
| MOSFET 高侧导通电阻 | RDS-ON-HS | | 93 | | mΩ | 负载 = 1A | 9 |
| MOSFET 低侧导通电阻 | RDS-ON-LS | | 61 | | mΩ | 负载 = 1A | 9 |
| 结至环境热阻 | RθJA | | 43.1 | | °C/W | JESD 51-7,4层JEDEC板仿真 | 7 |
| 结至外壳(顶部)热阻 | RθJC(top) | | 35.4 | | °C/W | | 7 |
| 结至电路板热阻 | RθJB | | 18.5 | | °C/W | | 7 |
| 结至顶部特征参数 | ΨJT | | 0.9 | | °C/W | | 7 |
| 结至电路板特征参数 | ΨJB | | 18.5 | | °C/W | | 7 |
| 结至外壳(底部)热阻 | RθJC(bot) | | 4.5 | | °C/W | | 7 |
## CAD (KiCad official)
- Symbol: `LM63610DQPWPRQ1`
- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`
- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lm63610dqpwprq1-etched.step` / `lm63610dqpwprq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm63610dqpwprq1.step` / `lm63610dqpwprq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm63610-q1) (49 pp, sha256 `973de5edc4caace0`, retrieved 2026-10-31, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm63610dqpwprq1-datasheet.pdf)