Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM63610DQPWPRQ1

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM63610DQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW power_out Regulator switching node that connects to the power inductor; SW to PGND is rated -6 V to 40 V for transients under 10 ns in the HTSSOP package.
2 SW power_out Second switching node pin, tied to pin 1, that connects to the power inductor.
3 CBOOT power_in Bootstrap supply for the internal high-side driver; connect a 220nF quality capacitor between this pin and SW, with BOOT to SW rated -0.3 V to 5.5 V.
4 VCC power_out Internal 5 V LDO output that powers the internal control circuits; do not connect external loads, and place a 1µF quality capacitor between this pin and PGND.
5 RT input Switching-frequency programming input: tie to VCC for 400kHz, to AGND for 2.1MHz, or to a timing resistor for 250kHz to 2200kHz; it must not float and is rated 0 V to 5 V.
6 VSEL input Output-voltage select input: tie to VCC for 5 V, to AGND for 3.3 V, or to AGND through 10kΩ for an adjustable output; it must not float and is rated 0 V to 5 V.
7 SYNC/MODE input Mode selection and synchronization input: tie to VCC for FPWM, to AGND for automatic mode, or drive with an external clock (250kHz to 2200kHz); it is rated 0 V to 5 V.
8 RESET output Open-drain power-good flag that needs an external pull-up to a suitable supply, reads high for power good and low for fault, is forced low when EN is low, and may be left open if unused; RESET to AGND is rated -0.3 V to 16 V.
9 FB input Feedback input that connects to the output for fixed 5 V or 3.3 V operation or to a divider tap for adjustable operation (regulated to 1 V); it must not float or be grounded.
10 AGND power_in Analog ground and logic reference for the regulator and system; all electrical parameters are measured relative to this pin.
11 EN input Enable input with precision thresholds (VEN-H 1.425 V to 1.575 V rising, VEN-L 0.9 V to 0.94 V falling); it may connect directly to VIN but must not float.
12 VIN power_in Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND, with a 220nF capacitor within 1 mm of the VIN and PGND pins.
13 VIN power_in Regulator input supply, rated 3.5 V minimum operating and -0.3 V to 40 V absolute maximum in the HTSSOP package; place a quality bypass capacitor directly between this pin and PGND.
14 NC unconnected No internal connection to the device circuitry.
15 PGND power_in Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors.
16 PGND power_in Power ground terminal; connect to system ground and AGND, using short, wide traces to the bypass capacitors.
17 DAP power_in Exposed die-attach pad for electrical ground and heat sinking; solder directly to the system ground plane.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN 至 PGND(HTSSOP 封装) -0.3 40 V 6
EN 至 AGND(HTSSOP 封装) -0.3 40 V 6
SYNC/MODE 到 AGND -0.3 6 V 6
VSEL 和 RT 至 AGND -0.3 5.5 V 6
RESET 至 AGND -0.3 16 V 6
FB 至 AGND(固定 VOUT 模式) -0.3 16 V 6
FB 至 AGND(可调 VOUT 模式) -0.3 5.5 V 6
AGND 到 PGND -0.3 0.3 V 6
SW 至 PGND,瞬变时间不到 10ns(HTSSOP 封装) -6 40 V 6
BOOT 至 SW -0.3 5.5 V 6
VCC 到 AGND VCC -0.3 5.5 V 6
结温 TJ TJ -40 150 °C 6
贮存温度 Tstg Tstg -65 150 °C 6
SYNC/MODE、VSEL 和 RT 至 AGND 0 5 V 在建议的 -40°C 到 150°C 结温范围内测得 6
RESET 0 5 V 在建议的 -40°C 到 150°C 结温范围内测得 6
VOUT VOUT 1 20 V 在建议的 -40°C 到 150°C 结温范围内测得 6
VCC VCC 2.7 5.25 V 在建议的 -40°C 到 150°C 结温范围内测得 6
IOUT,LM63610 IOUT 0 1 A 在建议的 -40°C 到 150°C 结温范围内测得 6
VIN 最小工作输入电压 3.5 V 8
非开关输入电流 IQ(在 VIN 引脚处测得) IQ 23 40 µA VEN = 3.3V,VFB = 1.2× 稳压值 8
关断静态电流 ISD(在 VIN 引脚处测得) ISD 5.3 10 µA VEN = 0V 8
最小工作电压阈值 下降 VIN VUVLO_F 2.6 3 V 下降 VIN,IVCC = 0A 8
触发 OVP 时 SW 上的下拉电流 IPOR 0.5 1.5 2.5 mA VEN = 0V、VSW = 5V 8
VOUT 的精密使能高电平 VEN-H 1.425 1.5 1.575 V VEN 上升 8
VOUT 的精密使能低电平 VEN-L 0.9 0.94 V VEN 下降 8
使能输入漏电流 ILKG-EN -100 0.2 300 nA VEN = 13.5V 8
用于在启动时选择有效可调输出电压的电阻器范围 RSEL-ADJ 8 50 kΩ 8
内部 VCC 电压 VCC 4.75 5 5.25 V 6V ≤ VIN ≤ 最大工作 VIN 8
VCC 钳位电压 VCCM 5.25 5.55 5.8 V 向 VCC 提供 1mA 8
反馈电压(可调) VFB_ADJ 0.985 1 1.015 V VIN = 3.5 - 最大工作 VIN 8
反馈电压(5V) VFB_5V 4.925 5 5.075 V VIN = 5.5 - 最大工作 VIN 8
反馈电压(3.3V) VFB_3p3V 3.25 3.3 3.35 V VIN = 3.8 - 最大工作 VIN 8
FB 引脚上的输入漏电流(可调) IFB_ADJ 0.2 100 nA FB = 1V 8
FB 引脚上的输入漏电流(5V) IFB_5V 2.89 3.4 µA FB = 5V 8
FB 引脚上的输入漏电流(3.3V) IFB_3p3V 1.67 2 µA FB = 3.3V 8
ISC 短路高侧电流限值 ISC 1.9 2.25 2.7 A 1A 版本 8
低侧电流限值 ILS-LIMIT 1.5 1.8 2.12 A 8
最小峰值电感器电流 IPEAK-MIN 0.375 0.7 A 8
负电流限值 IL-NEG -1.49 -1.2 -0.75 A 8
FB 引脚上的断续阈值 VHICCUP 37 42 47 % 8
RESET 阈值上限 - 上升 FB 电压 VRESET-HIGH 110 112 115 % 8
RESET 阈值下限 - 下降 FB 电压 VRESET-LOW 91 93 95 % 8
RESET 迟滞 FB 电压 VRESET-HYS 1.1 1.8 2.5 % 8
正常 PG 功能的最小输入电压 V_RESET_VALID 0.7 1.04 1.25 V 在 VRESET 小于 0.4V 且通过 10kΩ 上拉至外部 5V 的情况下测得 8
RESET 导通电阻 RRESET 60 150 Ω VEN = 5V,1mA 上拉电流 8
RESET 导通电阻 RRESET 40 125 Ω VEN = 0V,1mA 上拉电流 9
同步输入和模式高电平阈值 VSYNC-HIGH 1.5 1.8 V 9
同步输入和模式低电平阈值 VSYNC-LOW 0.8 1.15 V 9
过流断续重试延迟时间 tOC 70 104 140 ms 10
内部软启动时间 tSS 1 1.6 2.2 ms 10
RESET 边沿抗尖峰延迟 tdg 10 17 30 µs 10
RESET 运行时间 tRISE-DELAY 2 3 5 ms FB 时间在 RESET 释放前必须有效。 10
MOSFET 高侧导通电阻 RDS-ON-HS 93 mΩ 负载 = 1A 9
MOSFET 低侧导通电阻 RDS-ON-LS 61 mΩ 负载 = 1A 9
结至环境热阻 RθJA 43.1 °C/W JESD 51-7,4层JEDEC板仿真 7
结至外壳(顶部)热阻 RθJC(top) 35.4 °C/W 7
结至电路板热阻 RθJB 18.5 °C/W 7
结至顶部特征参数 ΨJT 0.9 °C/W 7
结至电路板特征参数 ΨJB 18.5 °C/W 7
结至外壳(底部)热阻 RθJC(bot) 4.5 °C/W 7

CAD (KiCad official)

  • Symbol: LM63610DQPWPRQ1
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm63610dqpwprq1-etched.step / lm63610dqpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm63610dqpwprq1.step / lm63610dqpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (49 pp, sha256 973de5edc4caace0, retrieved 2026-10-31, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF