3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM53601AQDSXTQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM53601AQDSXTQ1 from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Regulator switch node. Connect to output inductor. |
| 2 | BOOT | power_in | High side gate driver upper supply rail; connect 100-nF capacitor from SW to BOOT with internal diode charging capacitor while SW is low. |
| 3 | VCC | power_out | Internal 3-V regulator output used as supply to internal control circuits; connect high quality 1.0-μF capacitor from this pin to GND for adjustable versions. |
| 4 | FB | input | Feedback input for adjustable version only; connect to output through voltage divider which determines output voltage set point. |
| 5 | BIAS | power_in | Power source for VCC regulator in adjustable version; connect to output node and place 10-nF bypass capacitor immediately adjacent to this pin. |
| 6 | RESET | output | Open drain reset output; high indicates regulator OK, low indicates regulator fault; connect through current limiting pull up resistor to suitable voltage supply. |
| 7 | EN | input | Enable input to regulator; high enables operation, low disables; can be connected to VIN but do not float. |
| 8 | VIN | power_in | Input supply to regulator with range 3.8V to 36V after startup; connect input bypass capacitors directly between this pin and GND. |
| 9 | SYNC/MODE | input | Multifunction mode control input tolerant to input voltage; external clock synchronization or tied high selects forced PWM mode, tied low selects AUTO mode with diode emulation. |
| 10 | GND | power_in | Ground connection; bypass to VIN immediately adjacent to this pin. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | VIN | -0.3 | 42 | V | Over junction temp -40°C to 150°C | 5 | |
| SW to GND | -0.3 | V | Over junction temp -40°C to 150°C; max printed as VIN+0.3 V | 5 | |||
| BOOT to SW | -0.3 | 3.6 | V | Over junction temp -40°C to 150°C | 5 | ||
| EN to GND | -0.3 | 42 | V | Over junction temp -40°C to 150°C | 5 | ||
| BIAS to GND (ADJ version) | -0.3 | 16 | V | LM53600-Q1/LM53601-Q1-ADJ; over junction temp -40°C to 150°C | 5 | ||
| FB to GND (ADJ version) | -0.3 | 5.5 | V | LM53600-Q1/LM53601-Q1-ADJ; over junction temp -40°C to 150°C | 5 | ||
| RESET to GND | -0.3 | 8 | V | Over junction temp -40°C to 150°C | 5 | ||
| RESET sink current | 8 | mA | Over junction temp -40°C to 150°C | 5 | |||
| SYNC/MODE to GND | -0.3 | 42 | V | Over junction temp -40°C to 150°C | 5 | ||
| VCC | VCC | -0.3 | 3.6 | V | Over junction temp -40°C to 150°C | 5 | |
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| Input voltage range after startup | 3.8 | 36 | V | After startup | 5 | ||
| Output adjustment range (ADJ) | 3.3 | 6 | V | LM53601-Q1-ADJ | 5 | ||
| Load current range | 0 | 1000 | mA | LM53601-Q1 | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Initial output voltage accuracy | VFB | -1 | 1 | % | Vin = 3.8 V to 36 V, Tj = 25°C, Open Loop | 6 | |
| Initial output voltage accuracy | VFB | -1.5 | 1.5 | % | Vin = 3.8 V to 36 V, Open Loop | 6 | |
| Minimum input voltage to operate | Vin_UVLO | 3.2 | 3.6 | 3.75 | V | Rising | 6 |
| Minimum input voltage hysteresis | Vin_UVLO_hyst | 0.2 | 0.3 | 0.35 | V | Hysteresis | 6 |
| RESET upper threshold voltage | Vreset_OV | 105 | 106.5 | 110 | % | Rising, % of Vout | 6 |
| RESET lower threshold voltage | Vreset_UV | 92 | 94 | 97 | % | Falling, % Vout | 6 |
| Switching frequency | Fsw | 1.89 | 2.1 | 2.4 | MHz | VIN = 13.5 V, center frequency with spread spectrum, PWM operation | 7 |
| Sync frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | Output setting + 1 V < VIN < 18 V | 7 |
| Sync input duty cycle range | DSYNC | 25 | 75 | % | High state input < 5.5 V and > 2.3 V | 7 | |
| SYNC/MODE input threshold voltage, input high (MODE=FPWM) | VSYNC/MODE | 1.5 | V | MODE=FPWM | 7 | ||
| SYNC/MODE input threshold voltage, input low (MODE = AUTO with diode emulation) | VSYNC/MODE | 0.4 | V | MODE = AUTO with diode emulation | 7 | ||
| Frequency span of spread spectrum operation | FSSS | -4 | 4 | % | 7 | ||
| High side switch current limit | IL_HS | 1.5 | 1.83 | 2.1 | A | LM53601-Q1, duty cycle approaches 0% | 7 |
| Low side switch current limit | IL_LS | 1 | 1.2 | 1.43 | A | LM53601-Q1 | 7 |
| Negative current limit | IL_NEG | -0.7 | A | LM53601-Q1, MODE/SYNC = High | 7 | ||
| Zero-cross current limit | IL_ZC | -0.01 | A | MODE/SYNC = Low | 7 | ||
| Enable input threshold voltage - rising | VEN | 1.7 | 2 | V | Enable rising | 7 | |
| Enable threshold hysteresis | VEN_HYST | 0.4 | 0.55 | V | 7 | ||
| Minimum input to output voltage differential to maintain FSW >= 1.85 MHz, without inductor DCR drop | VDROP2 | 2 | V | VOUT = 3.3 V, IOUT = 1000 mA, FSW = 1.85 MHz, 2% regulation accuracy | 9 | ||
| Input current from FB to AGND | IFB | 20 | nA | LM53600-Q1-ADJ, FB = 1 V | 8 | ||
| Reference voltage for ADJ option only | Vref | 0.993 | 1 | 1.007 | V | Tj = 25°C | 8 |
| Reference voltage for ADJ option only | Vref | 0.985 | 1 | 1.015 | V | 8 | |
| Rdson of RESET output | RRESET | 50 | 120 | Ω | 8 | ||
| Thermal shutdown rising threshold | TSD | 151 | 167 | 185 | °C | 8 | |
| Maximum switch duty cycle | Dmax | 76 | % | Fsw = 2.1 MHz | 8 | ||
| Maximum switch duty cycle | Dmax | 96 | % | While in frequency fold back | 8 | ||
| Output voltage ADJ option | Vout_ADJ | -2 | 2 | % | VIN = VOUT + 0.6 V to 36 V, IOUT = 100 mA, FPWM mode | 8 | |
| Output voltage ADJ option | Vout_ADJ | -2 | 2.5 | % | VIN = VOUT + 0.6 V to 36 V, IOUT = 100 µA to 100 mA, Auto mode | 8 | |
| Load regulation for ADJ option | -1 | % | VIN = VOUT + 1 V to 36 V, IOUT = 0 A to 1 A, TJ = 125°C, FPWM mode | 8 | |||
| Minimum input to output voltage differential to maintain regulation accuracy, without inductor DCR drop | VDROP1 | 0.6 | V | VOUT=3.3 V, IOUT=1000 mA, +2/-3% output accuracy | 8 | ||
| Minimum input voltage for full functionality at 500-mA load, after start-up | Vin_min | 3.55 | V | VOUT = 3.3 V | 8 | ||
| Minimum input voltage for full functionality at 100% of max rated load, after start-up | Vin_min | 3.8 | V | VOUT = 3.3 V | 8 | ||
| Minimum switch on time | ton | 50 | 80.5 | ns | VIN = 18 V, IOUT = 500 mA | 9 | |
| Minimum switch off time | toff | 90 | 125 | ns | IOUT = 500 mA | 9 | |
| Delay time to RESET high signal | treset_act | 4 | 6 | 8 | ms | 9 | |
| Soft-start time | tSS | 1.3 | 3 | 4.5 | ms | Time from first SW node pulse to Vref at 90%, VIN ≥ 4.2 V | 9 |
| Bias current into BIAS pin for adjustable versions and FB pin for fixed versions | IB | 46 | 80 | µA | Vin = 13.5 V, Not switching, Vbias = 5 V, Mode = 0 V | 6 | |
| Operating quiescent current; measured at VIN pin | IQ | 6.5 | µA | Vin = 13.5 V, Not switching, Vbias = 5 V | 6 | ||
| Input current to VIN node of DC/DC utilizing the LM53600-Q1/LM53601-Q1 | IQ_VIN | 23 | µA | VIN = 13.5 V, VOUT = 3.3 V, IOUT = 0 A | 8 | ||
| Shutdown quiescent current; measured at VIN pin | ISD | 1.8 | µA | EN = 0, VIN = 13.5 V, Tj = 25°C | 6 | ||
| Junction-to-ambient thermal resistance (DSX WSON 10 pins) | RθJA | 46.2 | °C/W | DSX (WSON) 10 pins | 6 | ||
| Junction-to-case (top) thermal resistance (DSX WSON 10 pins) | RθJC(top) | 31.5 | °C/W | DSX (WSON) 10 pins | 6 | ||
| Junction-to-board thermal resistance (DSX WSON 10 pins) | RθJB | 20.9 | °C/W | DSX (WSON) 10 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance (DSX WSON 10 pins) | RθJC(bot) | 4.1 | °C/W | DSX (WSON) 10 pins | 6 |
CAD (KiCad official)
- Symbol:
LM53601AQDSXTQ1 - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm53601aqdsxtq1-etched.step/lm53601aqdsxtq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm53601aqdsxtq1.step/lm53601aqdsxtq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
d174c97c59a34282, retrieved 2026-10-07, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).