3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM536015QDSXRQ1
Texas Instruments · DC-DC Converters · WSON-10-EP(3x3)
LM536015QDSXRQ1 from Texas Instruments, in a WSON-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Regulator switch node connecting to output inductor, switching between VIN and GND with maximum voltage VIN+0.3V and minimum -0.3V. |
| 2 | BOOT | input | High side gate driver supply rail; connect 100-nF capacitor from SW pin to BOOT with internal diode charging when SW is low; voltage range -0.3V to 3.6V vs SW. |
| 3 | VCC | power_out | Internal 3V regulator output for control circuits; connect 1.0-μF high-quality capacitor to AGND (fixed version); voltage range -0.3V to 3.6V. |
| 4 | FB | input | Output voltage feedback input for fixed 5V version serving as both feedback and power source for VCC regulator; connect to 5V output node with 10-nF bypass capacitor; voltage range -0.3V to 16V. |
| 5 | AGND | power_in | Ground reference for input signals and FB feedback in fixed versions; voltage offset from GND must not exceed ±1V for durations greater than 1µs. |
| 6 | RESET | output | Open-drain reset output with high indicating regulator OK and low on fault or when EN is low; maximum sink current 8mA; voltage range -0.3V to 8V. |
| 7 | EN | input | Enable input; high enables regulator operation, low disables; can connect to VIN but must not float; tolerant to 42V transient for ≤100ms at ≤1% duty cycle. |
| 8 | VIN | power_in | Input power supply; operating range 3.8V to 36V with 42V maximum transient voltage for ≤100ms at ≤1% duty cycle; connect bypass capacitors directly to GND. |
| 9 | SYNC/MODE | input | Mode control input tolerant to 42V transients; accepts external clock for PWM synchronization at rising edge or internal clock for forced PWM (tied high) or AUTO mode with diode emulation (tied low); must not float. |
| 10 | GND | power_in | Ground return and bypass reference for VIN; bypass capacitors must be connected immediately adjacent to this pin. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range after startup | 3.8 | 36 | V | after startup | 5 | ||
| Output voltage range, 5 V option | 0 | 5.5 | V | 5 V option | 5 | ||
| Load current range, LM53601-Q1 | 0 | 1000 | mA | LM53601-Q1 | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| VIN to GND | VIN | -0.3 | 42 | V | 5 | ||
| SW to GND | SW | -0.3 | V | 5 | |||
| BOOT to SW | BOOT | -0.3 | 3.6 | V | 5 | ||
| EN to GND | EN | -0.3 | 42 | V | 5 | ||
| FB to GND, 5.0 V fixed version | FB | -0.3 | 16 | V | LM53601-Q1 - 5.0 V | 5 | |
| RESET to GND | RESET | -0.3 | 8 | V | 5 | ||
| RESET sink current | 8 | mA | 5 | ||||
| SYNC/MODE to GND | SYNC/MODE | -0.3 | 42 | V | 5 | ||
| VCC | VCC | -0.3 | 3.6 | V | 5 | ||
| GND to AGND (fixed version only) | GND | -1 | 2 | V | Fixed version only | 5 | |
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| Initial output voltage accuracy, Tj=25°C | VFB | -1 | 1 | % | Vin= 3.8 V to 36 V, Tj=25°C, Open Loop | 6 | |
| Initial output voltage accuracy | VFB | -1.5 | 1.5 | % | Vin= 3.8 V to 36 V, Open Loop | 6 | |
| Bias current into FB pin (fixed version) | IB | 46 | 80 | µA | Vin= 13.5 V, Not switching Vbias= 5 V, Mode = 0 V | 6 | |
| Minimum input voltage to operate (rising) | Vin_UVLO | 3.2 | 3.6 | 3.75 | V | Rising | 6 |
| Minimum input voltage hysteresis | Vin_UVLO_hyst | 0.2 | 0.3 | 0.35 | V | Hysteresis | 6 |
| RESET upper threshold voltage | Vreset_OV | 105 | 106.5 | 110 | % | Rising, % of Vout | 6 |
| RESET lower threshold voltage | Vreset_UV | 92 | 94 | 97 | % | Falling, % Vout | 6 |
| Switching frequency, without spread spectrum, PWM | Fsw | 1.89 | 2.1 | 2.4 | MHz | VIN = 13.5 V, Without spread spectrum, PWM operation | 7 |
| Sync frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | Output setting + 1 V < VIN < 18 V | 7 |
| Sync input duty cycle range | DSYNC | 25 | 75 | % | High state input < 5.5 V and > 2.3 V | 7 | |
| SYNC/MODE input hysteresis | 0.185 | 1 | V | 7 | |||
| High side switch current limit, LM53601-Q1 | IL_HS | 1.5 | 1.83 | 2.1 | A | Duty cycle approaches 0% | 7 |
| Low side switch current limit, LM53601-Q1 | IL_LS | 1 | 1.2 | 1.43 | A | 7 | |
| Enable input threshold voltage, rising | VEN | 1.7 | 2 | V | Enable rising | 7 | |
| Enable threshold hysteresis | VEN_HYST | 0.4 | 0.55 | V | 7 | ||
| RESET output Rdson | RRESET | 50 | 120 | Ω | 8 | ||
| Thermal shutdown rising threshold | TSD | 151 | 167 | 185 | °C | 8 | |
| Thermal shutdown falling threshold | TSDF | 140 | 157 | °C | 8 | ||
| Output voltage, 5 V option, max recommended load | Vout_5V | 4.9 | 5 | 5.1 | V | VIN = 5.8 V to 36 V, IOUT = Maximum recommended load current | 8 |
| Output voltage, 5 V option, 100 µA to 100 mA, Auto mode | Vout_5V | 4.9 | 5.05 | 5.125 | V | VIN = 5.5 V to 36 V, IOUT=100 µA to 100 mA, typical value in Auto Mode | 8 |
| Minimum switch on time | ton | 50 | 80.5 | ns | VIN = 18 V, IOUT = 500 mA | 9 | |
| Minimum switch off time | toff | 90 | 125 | ns | IOUT = 500 mA | 9 | |
| Delay time to RESET high signal | treset_act | 4 | 6 | 8 | ms | 9 | |
| Soft-start time | tSS | 1.3 | 3 | 4.5 | ms | Time from first SW node pulse to Vref at 90%, VIN ≥4.2 V | 9 |
| Quiescent current measured at VIN pin (Tj=25°C) | IQ | 6.5 | µA | Vin= 13.5 V, Not switching Vbias= 5 V | 6 | ||
| Quiescent current measured at VIN pin (Tj=85°C) | IQ | 16 | µA | Vin= 13.5 V, Not switching Vbias= 5 V, Tj= 85°C | 6 | ||
| Shutdown quiescent current (Tj=25°C) | ISD | 1.8 | µA | EN = 0, VIN = 13.5 V, Tj = 25°C | 6 | ||
| Shutdown quiescent current (Tj=85°C) | ISD | 3 | µA | EN = 0, VIN = 13.5 V, Tj = 85°C | 6 | ||
| Minimum input voltage for proper RESET function | Vreset_valid | 1.5 | V | 50 µA pull-up to RESET pin, EN = 0 V, Tj = 25°C | 6 | ||
| RESET threshold difference from steady-state output voltage | Vreset_guard | 3.9 | % | Steady state output voltage and RESET threshold read at the same TJ, and VIN | 6 | ||
| Low level RESET output voltage | VOL | 0.4 | V | 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V, Tj = 25°C | 6 | ||
| Switching frequency, 36 V input, 5 V fixed output device | Fsw | 1.5 | MHz | VIN = 36 V, 5-V fixed output device | 7 | ||
| Enable pin input current | IEN | 2.7 | µA | VIN = VEN = 13.5 V | 7 | ||
| Negative current limit, LM53601-Q1 | IL_NEG | -0.7 | A | LM53601-Q1, MODE/SYNC = High | 7 | ||
| High side MOSFET Rdson | Rdson | 220 | mΩ | High side MOSFET | 7 | ||
| Low side MOSFET Rdson | Rdson | 200 | mΩ | Low side MOSFET | 7 | ||
| SYNC/MODE input high threshold | VSYNC/MODE | 1.5 | V | SYNC/MODE input high (MODE=FPWM) | 7 | ||
| SYNC/MODE input low threshold | VSYNC/MODE | 0.4 | V | SYNC/MODE input low (MODE = AUTO with diode emulation) | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 46.2 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC | 31.5 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 20.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.1 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM536015QDSXRQ1 - Footprint:
Package_SON:VSON-10-1EP_3x3mm_P0.5mm_EP1.2x2mm - 3D model: WSON-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm536015qdsxrq1-etched.step/lm536015qdsxrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm536015qdsxrq1.step/lm536015qdsxrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
d174c97c59a34282, retrieved 2026-10-03, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).