main
Ray
Publish 0.1.0
eb4e42b
LM5176QPWPRQ1
Texas Instruments · DC-DC Controllers · HTSSOP-28-EP
LM5176QPWPRQ1 from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/UVLO | input | Enable pin: below 0.4 V the device is in low-current shutdown, above 1.22 V the PWM is enabled provided VCC exceeds the VCC UV threshold. |
| 2 | VIN | power_in | Input supply pin to the IC, connect to a supply voltage between 4.2 V and 55 V. |
| 3 | VISNS | input | VIN sense input, connect to the power stage input rail. |
| 4 | MODE | input | Selects hiccup mode: 1.38 V to 2.22 V is CCM with hiccup enabled (RMODE to AGND = 93.1 kΩ), 2.6 V to VCC is CCM with hiccup disabled (RMODE = 200 kΩ or connect to VCC). |
| 5 | DITH | passive | A capacitor to AGND sets the dither rate modulating the oscillator frequency by 10% of the RT-set nominal frequency; grounding the pin disables dithering, and the voltage is ignored in external Sync mode. |
| 6 | RT/SYNC | input | Switching frequency programming pin with a resistor to AGND, also usable to synchronize the PWM controller to an external clock. |
| 7 | SLOPE | passive | A capacitor to AGND provides the slope compensation ramp for stable current mode operation in both buck and boost mode. |
| 8 | SS | passive | Soft-start programming pin; a capacitor between SS and AGND sets the soft-start time. |
| 9 | COMP | output | Error amplifier output; an external RC network compensates the regulator feedback loop. |
| 10 | AGND | power_in | Analog ground of the IC. |
| 11 | FB | input | Feedback pin for output voltage regulation, connected to a resistor divider from the converter output (0.8 V reference). |
| 12 | VOSNS | input | VOUT sense input, connect to the power stage output rail. |
| 13 | ISNS(-) | input | Negative input of the average current sense amplifier; at 50 mV across ISNS(+) and ISNS(-) a slow constant-current loop becomes active, and shorting both pins disables the feature. |
| 14 | ISNS(+) | input | Positive input of the average current sense amplifier; the sense resistor may be on the input or output side, and shorting it to ISNS(-) disables the feature. |
| 15 | CSG | input | Negative or ground input to the PWM current sense amplifier, connected directly to the low side of the current sense resistor. |
| 16 | CS | input | Positive input to the PWM current sense amplifier. |
| 17 | PGOOD | output | Open-drain power-good output pulled low when FB is outside a -9%/+10% window around the 0.8 V VREF. |
| 18 | SW2 | passive | Boost side switching node. |
| 19 | HDRV2 | output | High-side gate driver output, connected directly to the gate of the high-side MOSFET. |
| 20 | BOOT2 | passive | Bootstrap pin; an external capacitor between BOOT2 and SW2 biases the high-side MOSFET gate driver. |
| 21 | LDRV2 | output | Low-side gate driver output, connected directly to the gate of the low-side MOSFET. |
| 22 | PGND | power_in | Power ground of the IC, the high-current ground connection for the low-side gate drivers. |
| 23 | VCC | power_out | Output of the VCC bias regulator, connect a capacitor to ground. |
| 24 | BIAS | power_in | Optional input to the VCC bias regulator; for VBIAS > 8 V the VCC regulator draws power from BIAS, reducing loss at high VIN. |
| 25 | LDRV1 | output | Low-side gate driver output, connected directly to the gate of the low-side MOSFET. |
| 26 | BOOT1 | passive | Bootstrap pin; an external capacitor between BOOT1 and SW1 biases the high-side MOSFET gate driver. |
| 27 | HDRV1 | output | High-side gate driver output, connected directly to the gate of the high-side MOSFET. |
| 28 | SW1 | passive | Buck side switching node. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN/UVLO, VISNS, VOSNS, ISNS(+), ISNS(-) voltage | -0.3 | 60 | V | 5 | |||
| BIAS voltage | -0.3 | 40 | V | 5 | |||
| FB, SS, DITH, RT/SYNC, SLOPE, COMP voltage | -0.3 | 3.6 | V | 5 | |||
| SW1, SW2 voltage | -1 | 60 | V | 5 | |||
| SW1, SW2 voltage (20 ns transient) | -5 | 65 | V | 20 ns transient | 5 | ||
| VCC, MODE, PGOOD voltage | -0.3 | 8.5 | V | 5 | |||
| LDRV1, LDRV2 voltage | -0.3 | 8.5 | V | 5 | |||
| BOOT1, HDRV1 with respect to SW1 voltage | -0.3 | 8.5 | V | with respect to SW1 | 5 | ||
| BOOT2, HDRV2 with respect to SW2 voltage | -0.3 | 8.5 | V | with respect to SW2 | 5 | ||
| BOOT1, BOOT2 voltage | -0.3 | 68 | V | 5 | |||
| ISNS(+) with respect to ISNS(-) voltage | -0.3 | 0.3 | V | with respect to ISNS(-) | 5 | ||
| CS, CSG voltage | -0.3 | 0.3 | V | 5 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input bias voltage | VIN | 4.2 | 55 | V | 5 | ||
| Input power stage voltage with external bias | VISNS | 2.5 | 55 | V | BIAS ≥ 5 V or VIN ≥ 4.5 V | 5 | |
| Bias supply voltage range (when VCC in regulation) | BIAS | 8 | 36 | V | when VCC in regulation | 5 | |
| Output voltage range | VOSNS | 0.8 | 55 | V | 5 | ||
| Enable voltage range | EN/UVLO | 0 | 55 | V | 5 | ||
| Average current sense common mode range | ISNS(+), ISNS(-) | 0 | 55 | V | 5 | ||
| Operating temperature range | TJ | -40 | 150 | °C | 5 | ||
| Operating frequency range | Fsw | 100 | 600 | kHz | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 32.6 | °C/W | 28 pins PWP (HTSSOP) | 6 | ||
| Junction-to-board thermal resistance | RθJB | 8.2 | °C/W | 28 pins PWP (HTSSOP) | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1 | °C/W | 28 pins PWP (HTSSOP) | 6 | ||
| VIN shutdown current | IQ | 2.6 | 10 | µA | VEN/UVLO = 0 V | 6 | |
| VIN operating current | 2 | 4 | mA | VEN/UVLO = 2 V, VFB = 0.9 V | 6 | ||
| VCC regulation voltage | VVCC(VIN) | 6.95 | 7.35 | 7.88 | V | VBIAS = 0 V, VCC open | 6 |
| VCC undervoltage lockout | VUV(VCC) | 3.11 | 3.27 | 3.43 | V | VCC increasing | 6 |
| BIAS switchover voltage | VBIAS(SW) | 7.25 | 8 | 8.75 | V | VIN = 24 V | 6 |
| Standby threshold | VEN(STBY) | 0.55 | 0.82 | 0.97 | V | EN/UVLO rising | 6 |
| Standby source current | IEN(STBY) | 1 | 2 | 3 | µA | VEN/UVLO = 1.1 V | 6 |
| Operating threshold | VEN(OP) | 1.17 | 1.22 | 1.29 | V | EN/UVLO rising | 6 |
| Feedback reference voltage | VREF | 0.788 | 0.8 | 0.812 | V | FB = COMP | 6 |
| Soft-start pull up current | ISS | 3.75 | 5 | 6.35 | µA | VSS = 0 V | 6 |
| Switching frequency 1 | fSW(1) | 175 | 200 | 225 | kHz | RT = 40 kΩ | 6 |
| Switching frequency 2 | fSW(2) | 350 | 390 | 430 | kHz | RT = 20 kΩ | 6 |
| Buck current limit threshold (Valley) | VCS(BUCK) | 66 | 80 | 94 | mV | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost current limit threshold (Peak) | VCS(BOOST) | 100 | 120 | 140 | mV | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Average current loop regulation target | VSNS | 43 | 50 | 57 | mV | VISNS(-) = 24 V, sweep ISNS(+), VSS = 0.8 V | 7 |
| Buck adaptive slope current | ISLOPE | 24 | 30 | 35 | µA | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost adaptive slope current | ISLOPE | 13 | 17 | 21 | µA | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Source current out of MODE pin | IMODE | 17 | 20 | 23 | µA | 7 | |
| CCM with hiccup threshold | VCCM_HIC | 1.18 | 1.28 | 1.38 | V | 7 | |
| CCM no hiccup threshold | VCCM | 2.22 | 2.4 | 2.6 | V | 7 | |
| PGOOD trip threshold for falling FB | VPGD | -9 | % | Measured with respect to VREF | 8 | ||
| PGOOD trip threshold for rising FB | VPGD | 10 | % | Measured with respect to VREF | 8 | ||
| PGOOD sink current | ISINK(PGD) | 2 | 4.2 | 6.5 | mA | VPGOOD = 0.4 V | 8 |
| Output overvoltage threshold at FB pin | VOVP | 10 | % | Measured with respect to VREF | 8 | ||
| Driver peak source current | IHDRV1,2 | 1.8 | A | VBOOT - VSW = 7 V | 8 | ||
| Driver peak sink current | IHDRV1,2 | 2.2 | A | VBOOT - VSW = 7 V | 8 | ||
| Driver pull up resistance | RHDRV1,2 | 1.8 | Ω | VBOOT - VSW = 7 V | 8 | ||
| Driver pull down resistance | RHDRV1,2 | 1.1 | Ω | VBOOT - VSW = 7 V | 8 | ||
| Dead time HDRV1,2 off to LDRV1,2 on | tDT1 | 45 | ns | 8 | |||
| Dead time LDRV1,2 off to HDRV1,2 on | tDT2 | 45 | ns | 8 | |||
| Thermal shutdown temperature | TSD | 165 | °C | 8 |
CAD (KiCad official)
- Symbol:
LM5176QPWPRQ1 - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
lm5176qpwprq1-etched.step/lm5176qpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5176qpwprq1.step/lm5176qpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
8c9623c7002d7f57, retrieved 2026-11-07, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM5176QPWPRQ1
**Texas Instruments** · DC-DC Controllers · HTSSOP-28-EP
LM5176QPWPRQ1 from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN/UVLO | input | Enable pin: below 0.4 V the device is in low-current shutdown, above 1.22 V the PWM is enabled provided VCC exceeds the VCC UV threshold. |
| 2 | VIN | power_in | Input supply pin to the IC, connect to a supply voltage between 4.2 V and 55 V. |
| 3 | VISNS | input | VIN sense input, connect to the power stage input rail. |
| 4 | MODE | input | Selects hiccup mode: 1.38 V to 2.22 V is CCM with hiccup enabled (RMODE to AGND = 93.1 kΩ), 2.6 V to VCC is CCM with hiccup disabled (RMODE = 200 kΩ or connect to VCC). |
| 5 | DITH | passive | A capacitor to AGND sets the dither rate modulating the oscillator frequency by 10% of the RT-set nominal frequency; grounding the pin disables dithering, and the voltage is ignored in external Sync mode. |
| 6 | RT/SYNC | input | Switching frequency programming pin with a resistor to AGND, also usable to synchronize the PWM controller to an external clock. |
| 7 | SLOPE | passive | A capacitor to AGND provides the slope compensation ramp for stable current mode operation in both buck and boost mode. |
| 8 | SS | passive | Soft-start programming pin; a capacitor between SS and AGND sets the soft-start time. |
| 9 | COMP | output | Error amplifier output; an external RC network compensates the regulator feedback loop. |
| 10 | AGND | power_in | Analog ground of the IC. |
| 11 | FB | input | Feedback pin for output voltage regulation, connected to a resistor divider from the converter output (0.8 V reference). |
| 12 | VOSNS | input | VOUT sense input, connect to the power stage output rail. |
| 13 | ISNS(-) | input | Negative input of the average current sense amplifier; at 50 mV across ISNS(+) and ISNS(-) a slow constant-current loop becomes active, and shorting both pins disables the feature. |
| 14 | ISNS(+) | input | Positive input of the average current sense amplifier; the sense resistor may be on the input or output side, and shorting it to ISNS(-) disables the feature. |
| 15 | CSG | input | Negative or ground input to the PWM current sense amplifier, connected directly to the low side of the current sense resistor. |
| 16 | CS | input | Positive input to the PWM current sense amplifier. |
| 17 | PGOOD | output | Open-drain power-good output pulled low when FB is outside a -9%/+10% window around the 0.8 V VREF. |
| 18 | SW2 | passive | Boost side switching node. |
| 19 | HDRV2 | output | High-side gate driver output, connected directly to the gate of the high-side MOSFET. |
| 20 | BOOT2 | passive | Bootstrap pin; an external capacitor between BOOT2 and SW2 biases the high-side MOSFET gate driver. |
| 21 | LDRV2 | output | Low-side gate driver output, connected directly to the gate of the low-side MOSFET. |
| 22 | PGND | power_in | Power ground of the IC, the high-current ground connection for the low-side gate drivers. |
| 23 | VCC | power_out | Output of the VCC bias regulator, connect a capacitor to ground. |
| 24 | BIAS | power_in | Optional input to the VCC bias regulator; for VBIAS > 8 V the VCC regulator draws power from BIAS, reducing loss at high VIN. |
| 25 | LDRV1 | output | Low-side gate driver output, connected directly to the gate of the low-side MOSFET. |
| 26 | BOOT1 | passive | Bootstrap pin; an external capacitor between BOOT1 and SW1 biases the high-side MOSFET gate driver. |
| 27 | HDRV1 | output | High-side gate driver output, connected directly to the gate of the high-side MOSFET. |
| 28 | SW1 | passive | Buck side switching node. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Power Supply Chip |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN/UVLO, VISNS, VOSNS, ISNS(+), ISNS(-) voltage | | -0.3 | | 60 | V | | 5 |
| BIAS voltage | | -0.3 | | 40 | V | | 5 |
| FB, SS, DITH, RT/SYNC, SLOPE, COMP voltage | | -0.3 | | 3.6 | V | | 5 |
| SW1, SW2 voltage | | -1 | | 60 | V | | 5 |
| SW1, SW2 voltage (20 ns transient) | | -5 | | 65 | V | 20 ns transient | 5 |
| VCC, MODE, PGOOD voltage | | -0.3 | | 8.5 | V | | 5 |
| LDRV1, LDRV2 voltage | | -0.3 | | 8.5 | V | | 5 |
| BOOT1, HDRV1 with respect to SW1 voltage | | -0.3 | | 8.5 | V | with respect to SW1 | 5 |
| BOOT2, HDRV2 with respect to SW2 voltage | | -0.3 | | 8.5 | V | with respect to SW2 | 5 |
| BOOT1, BOOT2 voltage | | -0.3 | | 68 | V | | 5 |
| ISNS(+) with respect to ISNS(-) voltage | | -0.3 | | 0.3 | V | with respect to ISNS(-) | 5 |
| CS, CSG voltage | | -0.3 | | 0.3 | V | | 5 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 5 |
| Input bias voltage | VIN | 4.2 | | 55 | V | | 5 |
| Input power stage voltage with external bias | VISNS | 2.5 | | 55 | V | BIAS ≥ 5 V or VIN ≥ 4.5 V | 5 |
| Bias supply voltage range (when VCC in regulation) | BIAS | 8 | | 36 | V | when VCC in regulation | 5 |
| Output voltage range | VOSNS | 0.8 | | 55 | V | | 5 |
| Enable voltage range | EN/UVLO | 0 | | 55 | V | | 5 |
| Average current sense common mode range | ISNS(+), ISNS(-) | 0 | | 55 | V | | 5 |
| Operating temperature range | TJ | -40 | | 150 | °C | | 5 |
| Operating frequency range | Fsw | 100 | | 600 | kHz | | 5 |
| Junction-to-ambient thermal resistance | RθJA | | 32.6 | | °C/W | 28 pins PWP (HTSSOP) | 6 |
| Junction-to-board thermal resistance | RθJB | | 8.2 | | °C/W | 28 pins PWP (HTSSOP) | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 1 | | °C/W | 28 pins PWP (HTSSOP) | 6 |
| VIN shutdown current | IQ | | 2.6 | 10 | µA | VEN/UVLO = 0 V | 6 |
| VIN operating current | | | 2 | 4 | mA | VEN/UVLO = 2 V, VFB = 0.9 V | 6 |
| VCC regulation voltage | VVCC(VIN) | 6.95 | 7.35 | 7.88 | V | VBIAS = 0 V, VCC open | 6 |
| VCC undervoltage lockout | VUV(VCC) | 3.11 | 3.27 | 3.43 | V | VCC increasing | 6 |
| BIAS switchover voltage | VBIAS(SW) | 7.25 | 8 | 8.75 | V | VIN = 24 V | 6 |
| Standby threshold | VEN(STBY) | 0.55 | 0.82 | 0.97 | V | EN/UVLO rising | 6 |
| Standby source current | IEN(STBY) | 1 | 2 | 3 | µA | VEN/UVLO = 1.1 V | 6 |
| Operating threshold | VEN(OP) | 1.17 | 1.22 | 1.29 | V | EN/UVLO rising | 6 |
| Feedback reference voltage | VREF | 0.788 | 0.8 | 0.812 | V | FB = COMP | 6 |
| Soft-start pull up current | ISS | 3.75 | 5 | 6.35 | µA | VSS = 0 V | 6 |
| Switching frequency 1 | fSW(1) | 175 | 200 | 225 | kHz | RT = 40 kΩ | 6 |
| Switching frequency 2 | fSW(2) | 350 | 390 | 430 | kHz | RT = 20 kΩ | 6 |
| Buck current limit threshold (Valley) | VCS(BUCK) | 66 | 80 | 94 | mV | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost current limit threshold (Peak) | VCS(BOOST) | 100 | 120 | 140 | mV | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Average current loop regulation target | VSNS | 43 | 50 | 57 | mV | VISNS(-) = 24 V, sweep ISNS(+), VSS = 0.8 V | 7 |
| Buck adaptive slope current | ISLOPE | 24 | 30 | 35 | µA | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost adaptive slope current | ISLOPE | 13 | 17 | 21 | µA | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Source current out of MODE pin | IMODE | 17 | 20 | 23 | µA | | 7 |
| CCM with hiccup threshold | VCCM_HIC | 1.18 | 1.28 | 1.38 | V | | 7 |
| CCM no hiccup threshold | VCCM | 2.22 | 2.4 | 2.6 | V | | 7 |
| PGOOD trip threshold for falling FB | VPGD | -9 | | | % | Measured with respect to VREF | 8 |
| PGOOD trip threshold for rising FB | VPGD | | | 10 | % | Measured with respect to VREF | 8 |
| PGOOD sink current | ISINK(PGD) | 2 | 4.2 | 6.5 | mA | VPGOOD = 0.4 V | 8 |
| Output overvoltage threshold at FB pin | VOVP | | | 10 | % | Measured with respect to VREF | 8 |
| Driver peak source current | IHDRV1,2 | | | 1.8 | A | VBOOT - VSW = 7 V | 8 |
| Driver peak sink current | IHDRV1,2 | | | 2.2 | A | VBOOT - VSW = 7 V | 8 |
| Driver pull up resistance | RHDRV1,2 | | | 1.8 | Ω | VBOOT - VSW = 7 V | 8 |
| Driver pull down resistance | RHDRV1,2 | | | 1.1 | Ω | VBOOT - VSW = 7 V | 8 |
| Dead time HDRV1,2 off to LDRV1,2 on | tDT1 | | | 45 | ns | | 8 |
| Dead time LDRV1,2 off to HDRV1,2 on | tDT2 | | | 45 | ns | | 8 |
| Thermal shutdown temperature | TSD | | | 165 | °C | | 8 |
## CAD (KiCad official)
- Symbol: `LM5176QPWPRQ1`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `lm5176qpwprq1-etched.step` / `lm5176qpwprq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5176qpwprq1.step` / `lm5176qpwprq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5176-q1) (42 pp, sha256 `8c9623c7002d7f57`, retrieved 2026-11-07, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm5176qpwprq1-datasheet.pdf)