Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM5176QPWPRQ1

Texas Instruments · DC-DC Controllers · HTSSOP-28-EP

LM5176QPWPRQ1 from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN/UVLO input Enable pin: below 0.4 V the device is in low-current shutdown, above 1.22 V the PWM is enabled provided VCC exceeds the VCC UV threshold.
2 VIN power_in Input supply pin to the IC, connect to a supply voltage between 4.2 V and 55 V.
3 VISNS input VIN sense input, connect to the power stage input rail.
4 MODE input Selects hiccup mode: 1.38 V to 2.22 V is CCM with hiccup enabled (RMODE to AGND = 93.1 kΩ), 2.6 V to VCC is CCM with hiccup disabled (RMODE = 200 kΩ or connect to VCC).
5 DITH passive A capacitor to AGND sets the dither rate modulating the oscillator frequency by 10% of the RT-set nominal frequency; grounding the pin disables dithering, and the voltage is ignored in external Sync mode.
6 RT/SYNC input Switching frequency programming pin with a resistor to AGND, also usable to synchronize the PWM controller to an external clock.
7 SLOPE passive A capacitor to AGND provides the slope compensation ramp for stable current mode operation in both buck and boost mode.
8 SS passive Soft-start programming pin; a capacitor between SS and AGND sets the soft-start time.
9 COMP output Error amplifier output; an external RC network compensates the regulator feedback loop.
10 AGND power_in Analog ground of the IC.
11 FB input Feedback pin for output voltage regulation, connected to a resistor divider from the converter output (0.8 V reference).
12 VOSNS input VOUT sense input, connect to the power stage output rail.
13 ISNS(-) input Negative input of the average current sense amplifier; at 50 mV across ISNS(+) and ISNS(-) a slow constant-current loop becomes active, and shorting both pins disables the feature.
14 ISNS(+) input Positive input of the average current sense amplifier; the sense resistor may be on the input or output side, and shorting it to ISNS(-) disables the feature.
15 CSG input Negative or ground input to the PWM current sense amplifier, connected directly to the low side of the current sense resistor.
16 CS input Positive input to the PWM current sense amplifier.
17 PGOOD output Open-drain power-good output pulled low when FB is outside a -9%/+10% window around the 0.8 V VREF.
18 SW2 passive Boost side switching node.
19 HDRV2 output High-side gate driver output, connected directly to the gate of the high-side MOSFET.
20 BOOT2 passive Bootstrap pin; an external capacitor between BOOT2 and SW2 biases the high-side MOSFET gate driver.
21 LDRV2 output Low-side gate driver output, connected directly to the gate of the low-side MOSFET.
22 PGND power_in Power ground of the IC, the high-current ground connection for the low-side gate drivers.
23 VCC power_out Output of the VCC bias regulator, connect a capacitor to ground.
24 BIAS power_in Optional input to the VCC bias regulator; for VBIAS > 8 V the VCC regulator draws power from BIAS, reducing loss at high VIN.
25 LDRV1 output Low-side gate driver output, connected directly to the gate of the low-side MOSFET.
26 BOOT1 passive Bootstrap pin; an external capacitor between BOOT1 and SW1 biases the high-side MOSFET gate driver.
27 HDRV1 output High-side gate driver output, connected directly to the gate of the high-side MOSFET.
28 SW1 passive Buck side switching node.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-28-EP
Category Power Supply Chip
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, EN/UVLO, VISNS, VOSNS, ISNS(+), ISNS(-) voltage -0.3 60 V 5
BIAS voltage -0.3 40 V 5
FB, SS, DITH, RT/SYNC, SLOPE, COMP voltage -0.3 3.6 V 5
SW1, SW2 voltage -1 60 V 5
SW1, SW2 voltage (20 ns transient) -5 65 V 20 ns transient 5
VCC, MODE, PGOOD voltage -0.3 8.5 V 5
LDRV1, LDRV2 voltage -0.3 8.5 V 5
BOOT1, HDRV1 with respect to SW1 voltage -0.3 8.5 V with respect to SW1 5
BOOT2, HDRV2 with respect to SW2 voltage -0.3 8.5 V with respect to SW2 5
BOOT1, BOOT2 voltage -0.3 68 V 5
ISNS(+) with respect to ISNS(-) voltage -0.3 0.3 V with respect to ISNS(-) 5
CS, CSG voltage -0.3 0.3 V 5
Operating junction temperature TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
Input bias voltage VIN 4.2 55 V 5
Input power stage voltage with external bias VISNS 2.5 55 V BIAS ≥ 5 V or VIN ≥ 4.5 V 5
Bias supply voltage range (when VCC in regulation) BIAS 8 36 V when VCC in regulation 5
Output voltage range VOSNS 0.8 55 V 5
Enable voltage range EN/UVLO 0 55 V 5
Average current sense common mode range ISNS(+), ISNS(-) 0 55 V 5
Operating temperature range TJ -40 150 °C 5
Operating frequency range Fsw 100 600 kHz 5
Junction-to-ambient thermal resistance RθJA 32.6 °C/W 28 pins PWP (HTSSOP) 6
Junction-to-board thermal resistance RθJB 8.2 °C/W 28 pins PWP (HTSSOP) 6
Junction-to-case (bottom) thermal resistance RθJC(bot) 1 °C/W 28 pins PWP (HTSSOP) 6
VIN shutdown current IQ 2.6 10 µA VEN/UVLO = 0 V 6
VIN operating current 2 4 mA VEN/UVLO = 2 V, VFB = 0.9 V 6
VCC regulation voltage VVCC(VIN) 6.95 7.35 7.88 V VBIAS = 0 V, VCC open 6
VCC undervoltage lockout VUV(VCC) 3.11 3.27 3.43 V VCC increasing 6
BIAS switchover voltage VBIAS(SW) 7.25 8 8.75 V VIN = 24 V 6
Standby threshold VEN(STBY) 0.55 0.82 0.97 V EN/UVLO rising 6
Standby source current IEN(STBY) 1 2 3 µA VEN/UVLO = 1.1 V 6
Operating threshold VEN(OP) 1.17 1.22 1.29 V EN/UVLO rising 6
Feedback reference voltage VREF 0.788 0.8 0.812 V FB = COMP 6
Soft-start pull up current ISS 3.75 5 6.35 µA VSS = 0 V 6
Switching frequency 1 fSW(1) 175 200 225 kHz RT = 40 kΩ 6
Switching frequency 2 fSW(2) 350 390 430 kHz RT = 20 kΩ 6
Buck current limit threshold (Valley) VCS(BUCK) 66 80 94 mV VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V 7
Boost current limit threshold (Peak) VCS(BOOST) 100 120 140 mV VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V 7
Average current loop regulation target VSNS 43 50 57 mV VISNS(-) = 24 V, sweep ISNS(+), VSS = 0.8 V 7
Buck adaptive slope current ISLOPE 24 30 35 µA VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V 7
Boost adaptive slope current ISLOPE 13 17 21 µA VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V 7
Source current out of MODE pin IMODE 17 20 23 µA 7
CCM with hiccup threshold VCCM_HIC 1.18 1.28 1.38 V 7
CCM no hiccup threshold VCCM 2.22 2.4 2.6 V 7
PGOOD trip threshold for falling FB VPGD -9 % Measured with respect to VREF 8
PGOOD trip threshold for rising FB VPGD 10 % Measured with respect to VREF 8
PGOOD sink current ISINK(PGD) 2 4.2 6.5 mA VPGOOD = 0.4 V 8
Output overvoltage threshold at FB pin VOVP 10 % Measured with respect to VREF 8
Driver peak source current IHDRV1,2 1.8 A VBOOT - VSW = 7 V 8
Driver peak sink current IHDRV1,2 2.2 A VBOOT - VSW = 7 V 8
Driver pull up resistance RHDRV1,2 1.8 Ω VBOOT - VSW = 7 V 8
Driver pull down resistance RHDRV1,2 1.1 Ω VBOOT - VSW = 7 V 8
Dead time HDRV1,2 off to LDRV1,2 on tDT1 45 ns 8
Dead time LDRV1,2 off to HDRV1,2 on tDT2 45 ns 8
Thermal shutdown temperature TSD 165 °C 8

CAD (KiCad official)

  • Symbol: LM5176QPWPRQ1
  • Footprint: Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm
  • 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
  • 3D model files: lm5176qpwprq1-etched.step / lm5176qpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5176qpwprq1.step / lm5176qpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (42 pp, sha256 8c9623c7002d7f57, retrieved 2026-11-07, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF