Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM5163DDAR

Texas Instruments · DC-DC Converters · ESOP-8

LM5163DDAR from Texas Instruments, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground connection for internal circuits.
2 VIN power_in Regulator supply input pin to high-side power MOSFET and internal bias regulator; input voltage range 6 V to 100 V.
3 EN/UVLO input Precision enable and undervoltage lockout pin; converter in shutdown mode below 1.1 V, standby mode from 1.1 V to 1.5 V, and normal operation above 1.5 V.
4 RON input On-time programming pin; external resistor to GND sets buck switch on-time inversely proportional to input voltage.
5 FB input Feedback input to voltage regulation comparator maintained at internal reference voltage of 1.2 V.
6 PGOOD output Open-drain power good indicator output requiring external pullup resistor of 10 kΩ to 100 kΩ to indicate output voltage regulation status.
7 BST power_in Bootstrap gate-drive supply pin for high-side gate driver requiring 2.2 nF 50 V X7R ceramic capacitor connected between BST and SW.
8 SW power_out Switching node internally connected to source of high-side NMOS buck switch and drain of low-side NMOS synchronous rectifier; externally connected to power inductor.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package ESOP-8
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to GND -0.3 100 V 4
EN to GND -0.3 100 V 4
FB to GND -0.3 5.5 V 4
RON to GND -0.3 5.5 V 4
External BST to SW capacitance 1.5 2.5 nF 4
BST to GND -0.3 105.5 V 4
BST to SW -0.3 5.5 V 4
SW to GND -1.5 100 V 4
SW to GND (20-ns transient) -3 V 20-ns transient 4
PGOOD to GND -0.3 14 V 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
VIN input voltage VIN 6 100 V 4
Switch node voltage VSW 100 V 4
Enable voltage VEN/UVLO 100 V 4
Load current ILOAD 0.5 0.6 A 4
Switching frequency FSW 1000 kHz 4
External BST to SW capacitance CBST 2.2 nF 4
Programmable on-time tON 50 10000 ns 4
VIN active current IQ-ACTIVE 600 880 µA VEN = 2.5 V 5
VIN shutdown current IQ-SHUTDOWN 3 15 µA VEN = 0 V 5
VIN sleep current IQ-SLEEP1 10.5 25 µA VEN = 2.5 V, VFB = 1.5 V 5
Enable threshold rising VEN-RISING 1.45 1.5 1.55 V VEN/UVLO rising 5
Enable threshold falling VEN-FALLING 1.35 1.4 1.44 V VEN/UVLO falling 5
FB regulation voltage VREF 1.181 1.2 1.218 V VFB falling 5
FB upper threshold for PGOOD high to low VPG-UTH 1.105 1.14 1.175 V VFB rising 5
FB lower threshold for PGOOD high to low VPG-LTH 1.055 1.08 1.1 V VFB falling 5
Gate drive UVLO VBST-UV 2.7 3.4 V VBST rising 5
Internal soft-start time tSS 1.75 3 4.75 ms 6
Peak current limit threshold (HS) IPEAK1 0.63 0.75 0.87 A 6
Peak current limit threshold (LS) IPEAK2 0.63 0.75 0.87 A 6
Valley current limit threshold IVALLEY 0.5 0.6 0.72 A 6
Junction-to-ambient thermal resistance RθJA 43.4 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 59.5 °C/W 5
Junction-to-board thermal resistance RθJB 16.1 °C/W 5
Junction-to-top characterization parameter ΨJT 4 °C/W 5
Junction-to-board characterization parameter ΨJB 16.3 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 3.9 °C/W 5

CAD (KiCad official)

  • Symbol: LM5163DDAR
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm
  • 3D model: ESOP-8 (KiCad packages3D, STEP)
  • 3D model files: lm5163ddar-etched.step / lm5163ddar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5163ddar.step / lm5163ddar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (39 pp, sha256 4f75cb4abc02cdbe, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF