Generated by kicad-footprint-generator · KiCad file format 20260206
LM5158RTER
Texas Instruments · DC-DC Converters · WQFN-16(3x3)
LM5158RTER from Texas Instruments, in a WQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGND | power_in | Power ground pin and source connection of the internal N-channel power MOSFET (pins 1 and 16 are both PGND). |
| 2 | VCC | power_out | Output of the internal VCC regulator and supply input of the internal MOSFET driver; connect a 1-µF ceramic bypass capacitor from this pin to PGND. |
| 3 | BIAS | power_in | Supply voltage input to the VCC regulator (3.2 V to 60 V operating); connect a bypass capacitor from this pin to PGND. |
| 4 | PGOOD | output | Open-drain power-good indicator that goes low if FB is below the undervoltage threshold (VUVTH); connect a pullup resistor to the system voltage rail. |
| 5 | RT | input | Switching frequency setting pin; frequency is programmed by a single resistor between RT and AGND. |
| 6 | EN/UVLO/SYNC | input | Enable, programmable line UVLO and external synchronization clock input (negative pulse); converter shuts down below the enable threshold (VEN), must not be left floating, and should be connected to BIAS if not used. |
| 7 | AGND | power_in | Analog ground pin; connect to the analog ground plane through a wide and short path. |
| 8 | COMP | output | Output of the internal transconductance error amplifier; connect the loop compensation components between this pin and AGND. |
| 9 | FB | input | Inverting input of the error amplifier; connect a voltage divider to set the output voltage, with the low-side feedback resistor as close to AGND as possible. |
| 10 | SS | input | Soft-start time programming pin; an external capacitor to AGND and an internal current source set the reference ramp rate during soft start. |
| 11 | MODE | input | Selects hiccup mode protection and spread spectrum at initial power up: 0 V/AGND = both disabled, 370 mV/37.4 kΩ = hiccup and spread spectrum enabled, 620 mV/62.0 kΩ = hiccup enabled and spread spectrum disabled, >1 V/100 kΩ = hiccup disabled and spread spectrum enabled. |
| 12 | NC | unconnected | No internal electrical contact. |
| 13 | SW | passive | Switch pin and drain connection of the internal N-channel power MOSFET (85 V absolute maximum DC). |
| 14 | SW | passive | Switch pin and drain connection of the internal N-channel power MOSFET (85 V absolute maximum DC). |
| 15 | NC | unconnected | No internal electrical contact. |
| 16 | PGND | power_in | Power ground pin and source connection of the internal N-channel power MOSFET (pins 1 and 16 are both PGND). |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| BIAS to AGND | -0.3 | 65 | V | 6 | |||
| UVLO to AGND | -0.3 | V | max is VBIAS + 0.3 V | 6 | |||
| SS, RT to AGND | -0.3 | 3.8 | V | 6 | |||
| FB to AGND | -0.3 | 4 | V | 6 | |||
| MODE to AGND | -0.3 | 3.8 | V | 6 | |||
| PGND to AGND | -0.3 | 0.3 | V | 6 | |||
| VCC to AGND | -0.3 | 5.8 | V | 6 | |||
| PGOOD to AGND | -0.3 | 18 | V | 6 | |||
| SW to AGND (DC) | -0.3 | 85 | V | DC | 6 | ||
| SW to AGND (5-ns transient) | -6 | V | 5-ns transient | 6 | |||
| Junction temperature | TJ | -40 | 150 | °C | 6 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 6 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | ANSI/ESDA/JEDEC JS-001, all pins | 6 | |
| ESD CDM | V(ESD) | -500 | 500 | V | ANSI/ESDA/JEDEC JS-002 | 6 | |
| Boost converter input | VSUPPLY | 1.5 | 60 | V | when BIAS ≥ 3.2 V | 6 | |
| Boost converter output | VLOAD | 83 | V | min is VSUPPLY | 6 | ||
| BIAS input | VBIAS | 3.2 | 60 | V | 6 | ||
| UVLO input | VUVLO | 0 | 60 | V | 6 | ||
| FB input | VFB | 0 | 4 | V | 6 | ||
| Typical switching frequency | fSW | 100 | 2200 | kHz | 6 | ||
| Synchronization pulse frequency | fSYNC | 100 | 2200 | kHz | 6 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 6 | ||
| BIAS shutdown current | ISHUTDOWN(BIAS) | 2.6 | 5 | μA | VBIAS = 12 V, VUVLO = 0 V | 7 | |
| BIAS operating current | IOPERATING(BIAS) | 670 | 850 | μA | VBIAS = 12 V, VUVLO = 2.0 V, VFB = VREF, RT = 220 kΩ | 7 | |
| VCC regulation | VVCC-REG | 4.66 | 4.9 | 5.14 | V | VBIAS = 8 V, IVCC = 18 mA | 7 |
| VCC UVLO threshold | VVCC-UVLO(RISING) | 3.05 | 3.1 | 3.15 | V | VCC rising | 7 |
| Enable threshold rising | VEN(RISING) | 0.4 | 0.52 | 0.7 | V | EN rising | 7 |
| Enable threshold falling | VEN(FALLING) | 0.33 | 0.49 | 0.63 | V | EN falling | 7 |
| UVLO threshold rising | VUVLO(RISING) | 1.425 | 1.5 | 1.575 | V | UVLO rising | 7 |
| UVLO threshold falling | VUVLO(FALLING) | 1.37 | 1.45 | 1.52 | V | UVLO falling | 7 |
| UVLO hysteresis current | IUVLO | 4 | 5 | 6 | μA | VUVLO = 1.6 V | 7 |
| Soft-start current | ISS | 9 | 10 | 11 | μA | 7 | |
| Switching frequency | fsw1 | 85 | 100 | 115 | kHz | RT = 220 kΩ | 7 |
| Switching frequency | fsw2 | 388 | 440 | 492 | kHz | RT = 49.3 kΩ | 8 |
| Switching frequency | fsw3 | 1980 | 2200 | 2420 | kHz | RT = 9.09 kΩ | 8 |
| Maximum duty cycle limit | DMAX1 | 80 | 85 | 90 | % | RT = 9.09 kΩ | 8 |
| Maximum duty cycle limit | DMAX2 | 90 | 93 | 96 | % | RT = 220 kΩ | 8 |
| Internal MOSFET current limit LM5158 | ILIM | 3.26 | 3.75 | 4.24 | A | LM5158 | 8 |
| FB reference | VREF | 0.99 | 1 | 1.01 | V | 8 | |
| COMP clamp voltage rising | 2.5 | 2.8 | V | COMP rising (VUVLO = 2.0 V) | 8 | ||
| COMP clamp voltage falling | 1 | 1.1 | V | COMP falling | 8 | ||
| Overvoltage threshold rising | VOVTH | 107 | 110 | 113 | % | FB rising (reference to VREF) | 8 |
| Undervoltage threshold falling | VUVTH | 87 | 90 | 93 | % | FB falling (reference to VREF) | 8 |
| Internal MOSFET on-resistance | rDS(ON) | 133 | 290 | mΩ | VBIAS = 12 V | 8 | |
| Internal MOSFET on-resistance | rDS(ON) | 138 | 300 | mΩ | VBIAS = 3.5 V | 8 | |
| Switch leakage current | 1100 | nA | VSW = 12 V | 8 | |||
| Thermal shutdown threshold | TTSD | 175 | °C | Temperature rising | 8 | ||
| Junction-to-ambient thermal resistance | RθJA | 45.6 | °C/W | RTE(QFN) 16 pins | 7 | ||
| Junction-to-ambient thermal resistance (EVM) | RθJA | 32.7 | °C/W | LM5158EVM-BST | 7 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 44.8 | °C/W | 7 | |||
| Junction-to-board thermal resistance | RθJB | 19.1 | °C/W | 7 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 6.7 | °C/W | 7 |
CAD (KiCad official)
- Symbol:
LM5158RTER - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
lm5158rter-etched.step/lm5158rter-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5158rter.step/lm5158rter.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (45 pp, sha256
9e8875f070157c1d, retrieved 2026-10-26, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).