3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM51561QDSSRQ1
Texas Instruments · DC-DC Converters · WSON-12-EP(2x3)
LM51561QDSSRQ1 from Texas Instruments, in a WSON-12-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BIAS | power_in | Supply voltage input to internal VCC regulator; supports 2.97V to 60V operating range with 65V absolute maximum for automotive load dump transients. |
| 2 | VCC | power_in | Regulated output voltage from internal VCC regulator and supply input for MOSFET gate driver; 6.85V typical with absolute maximum 18V or VBIAS+0.3V. |
| 3 | GATE | output | N-channel MOSFET gate drive output capable of sourcing and sinking 1.5A peak current with output swing from 0.15V low state to VCC minus 0.25V high state. |
| 4 | GND | power_in | Ground return pin; connect directly to sense resistor ground through low-inductance wide and short path and to ground copper plane. |
| 5 | CS | input | Low-side current sense input; 100mV±7% peak current limit threshold with 0.3V DC and -1V for 50ns transient absolute maximum ratings. |
| 6 | COMP | output | Transconductance error amplifier output with 10MΩ output impedance and internal voltage clamps at 2.5-2.8V rising and 1-1.1V falling. |
| 7 | DITHOFF | input | Spread spectrum dithering selection input; internal dithering enabled when voltage is less than 1.0V or connected to GND, disabled when greater than 2.0V or connected to VCC. |
| 8 | FB | input | Inverting input of internal error amplifier; 1V±1% internal reference with 4.0V absolute maximum rating. |
| 9 | SS | input | Soft-start capacitor programming pin; charged by 10µA internal current source to ramp error amplifier reference during power-on soft start sequence. |
| 10 | RT | input | Switching frequency programming pin; regulated to 0.5V by internal regulator with programmable frequency range from 100kHz to 2.2MHz. |
| 11 | PGOOD | output | Power-good indicator open-drain output; pulls low when FB falls below undervoltage threshold with 18V absolute maximum and 1mA maximum sink capability. |
| 12 | UVLO/SYNC/EN | input | Undervoltage lockout and external clock synchronization input; 1.5V typical rising threshold and 1.45V typical falling threshold with 50mV hysteresis. |
| 13 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-12-EP(2x3) |
| Category | Power Management (PMIC) |
| Pins | 13 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| BIAS to GND | -0.3 | 65 | V | 5 | |||
| UVLO to GND | -0.3 | V | max printed as VBIAS+0.3 V | 5 | |||
| SS to GND | -0.3 | 3.8 | V | 5 | |||
| RT to GND | -0.3 | 3.8 | V | 5 | |||
| FB to GND | -0.3 | 4 | V | 5 | |||
| CS to GND | -0.3 | 0.3 | V | DC | 5 | ||
| CS to GND | -1 | V | 50ns transient | 5 | |||
| DITHOFF to GND | -0.3 | 18 | V | 5 | |||
| VCC to GND | -0.3 | 18 | V | 18 V or VBIAS+0.3 V, whichever is lower | 5 | ||
| GATE to GND | -1 | V | 50ns transient | 5 | |||
| PGOOD to GND | -0.3 | 18 | V | 5 | |||
| COMP to GND | -0.3 | V | 5 | ||||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| VBIAS Bias input | VBIAS | 2.97 | 60 | V | 2.97-16 V when VCC tied to BIAS; 3.5-60 V when VCC from internal regulator | 6 | |
| VCC voltage | VVCC | 2.97 | 16 | V | VCC pin voltage less than VBIAS + 0.3 V | 6 | |
| DITHOFF input | VDITHOFF | 0 | 16 | V | 6 | ||
| UVLO input | VUVLO | 0 | 60 | V | 6 | ||
| FB input | VFB | 0 | 4 | V | 6 | ||
| Typical switching frequency | fSW | 100 | 2200 | kHz | 6 | ||
| Synchronization pulse frequency | fSYNC | 100 | 2200 | kHz | 6 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 6 | ||
| BIAS shutdown current | ISHUTDOWN(BIAS) | 2.6 | 5 | uA | VBIAS = 12 V, VUVLO = 0 V | 6 | |
| BIAS operating current | IOPERATING(BIAS) | 490 | 550 | uA | VBIAS = 12 V, VUVLO = 2.0 V, VFB = VREF, RT = 220 kΩ | 6 | |
| VCC regulation | VVCC-REG | 6.5 | 6.85 | 7 | V | VBIAS = 8 V, No load | 6 |
| VCC UVLO threshold (rising) | VVCC-UVLO(RISING) | 2.75 | 2.85 | 2.95 | V | VCC rising | 6 |
| VCC sourcing current limit | IVCC-CL | 35 | 110 | mA | VBIAS = 10 V, VVCC = 0 V | 6 | |
| Enable threshold (rising) | VEN(RISING) | 0.4 | 0.52 | 0.7 | V | EN rising | 7 |
| Enable threshold (falling) | VEN(FALLING) | 0.33 | 0.49 | 0.63 | V | EN falling | 7 |
| UVLO / SYNC threshold (rising) | VUVLO(RISING) | 1.425 | 1.5 | 1.575 | V | UVLO rising | 7 |
| UVLO / SYNC threshold (falling) | VUVLO(FALLING) | 1.37 | 1.45 | 1.52 | V | UVLO falling | 7 |
| UVLO hysteresis current | IUVLO | 4 | 5 | 6 | uA | VUVLO = 1.6 V | 7 |
| Clock dithering threshold (rising) | VDITHOFF(RISING) | 1.1 | 1.7 | 2.1 | V | DITHOFF rising, VBIAS = 4 V | 7 |
| Clock dithering threshold (falling) | VDITHOFF(FALLING) | 0.6 | 1.2 | 1.8 | V | DITHOFF falling, VBIAS = 4 V | 7 |
| Soft-start current | ISS | 9 | 10 | 11 | uA | 7 | |
| Switching frequency (fsw1) | fsw1 | 85 | 100 | 115 | kHz | RT = 220 kΩ, VBIAS = 4 V | 7 |
| Switching frequency (fsw2) | fsw2 | 1980 | 2200 | 2420 | kHz | RT = 9.09 kΩ, VBIAS = 4 V | 7 |
| Maximum duty cycle limit (DMAX1) | DMAX1 | 80 | 85 | 90 | % | RT = 9.09 kΩ, VBIAS = 4 V | 7 |
| Maximum duty cycle limit (DMAX2) | DMAX2 | 90 | 93 | 96 | % | RT = 220 kΩ, VBIAS = 4 V | 7 |
| Peak slope compensation current | ISLOPE | 22.5 | 30 | 37.5 | uA | RT = 220 kΩ | 7 |
| Current limit threshold | VCLTH | 93 | 100 | 107 | mV | CS-GND | 7 |
| FB reference | VREF | 0.99 | 1 | 1.01 | V | LM5156, LM51561 | 7 |
| COMP clamp voltage (rising) | 2.5 | 2.8 | V | COMP rising (VUVLO = 2.0 V) | 7 | ||
| COMP clamp voltage (falling) | 1 | 1.1 | V | COMP falling | 7 | ||
| Over-voltage threshold (rising) | VOVTH | 107 | 110 | 113 | % | FB rising (referece to VREF) | 7 |
| Under-voltage threshold (falling) | VUVTH | 87 | 90 | 93 | % | FB falling (referece to VREF) | 7 |
| Thermal resistance, junction-to-ambient | RθJA | 58.2 | °C/W | 6 | |||
| Thermal resistance, junction-to-case (top) | RθJC(top) | 60.5 | °C/W | 6 | |||
| Thermal resistance, junction-to-board | RθJB | 27.2 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 1.8 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 27.2 | °C/W | 6 | |||
| Thermal resistance, junction-to-case (bottom) | RθJC(bot) | 4.7 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM51561QDSSRQ1 - Footprint:
Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65 - 3D model: WSON-12-EP(2x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
lm51561qdssrq1-etched.step/lm51561qdssrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm51561qdssrq1.step/lm51561qdssrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (50 pp, sha256
2f02152f7d3a5e51, retrieved 2026-10-01, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).