Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM51551QDSSRQ1

Texas Instruments · DC-DC Converters · WSON-12-EP(2x3)

LM51551QDSSRQ1 from Texas Instruments, in a WSON-12-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BIAS power_in Power supply input to VCC regulator operating from 2.97V to 45V with bypass capacitor to PGND.
2 VCC power_out Regulated power output from internal VCC regulator at 6.5V to 7V nominal supplying MOSFET driver with ceramic bypass capacitor to PGND.
3 GATE output N-channel MOSFET gate driver output with 1.5A peak current capability connected via short low-inductance path to MOSFET gate.
4 PGND power_in Power ground reference connected via wide short low-inductance path to current sense resistor ground.
5 CS input Current sense input for peak current mode control connected via short path to positive side of current sense resistor with 100mV threshold.
6 COMP output Transconductance error amplifier output with 10MΩ impedance and 7MHz bandwidth with loop compensation network connected between this pin and PGND.
7 AGND power_in Analog ground reference with wide short path connection required to analog ground plane.
8 FB input Error amplifier feedback input with 1V ±1% reference, voltage divider from output connected to set target output voltage in boost/SEPIC topologies.
9 SS input Soft-start programming pin with external capacitor and 10μA internal current source for setting startup ramp rate, capacitor ground to AGND.
10 RT input Switch frequency programming pin regulated to 0.5V, single external resistor to AGND programs switching frequency from 100kHz to 2.2MHz.
11 PGOOD output Open-drain power good indicator output goes low if feedback drops below 90% of 1V reference with 25μs glitch filter and pull-up resistor to system voltage.
12 UVLO/SYNC input UVLO threshold programming and enable/sync control pin from 0V to VBIAS+0.3V via resistor divider, supports external clock synchronization via negative pulse, do not leave floating.
13 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-12-EP(2x3)
Category Power Management (PMIC)
Pins 13

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
BIAS to AGND -0.3 50 V 5
UVLO to AGND -0.3 V 5
SS to AGND -0.3 3.8 V 5
RT to AGND -0.3 3.8 V 5
FB to AGND -0.3 3.8 V 5
CS to AGND -0.3 0.3 V DC 5
CS to AGND -1 V 100ns transient 5
CS to AGND -2 V 20ns transient 5
PGND to AGND -0.3 0.3 V 5
VCC to AGND -0.3 18 V 5
GATE to AGND -1 V 100ns transient 5
GATE to AGND -2 V 50ns transient 5
PGOOD to AGND -0.3 18 V 5
COMP to AGND -0.3 V 5
Junction temperature TJ -40 150 °C 5
Storage temperature Tstg -55 150 °C 5
BIAS input voltage VBIAS 2.97 45 V 6
VCC voltage VVCC 2.97 16 V 6
UVLO input voltage VUVLO 0 45 V 6
FB input voltage VFB 0 3.7 V 6
Typical switching frequency fSW 100 2200 kHz 6
Synchronization pulse frequency fSYNC 100 2200 kHz 6
Operating junction temperature TJ -40 150 °C 6
BIAS shutdown current ISHUTDOWN(BIAS) 2.6 5 uA VBIAS = 12V, VUVLO = 0V 6
BIAS operating current IOPERATING(BIAS) 480 540 uA VBIAS = 12V, VUVLO = 2V, VFB = VREF, RT = 220kΩ 6
VCC regulation, no load VVCC-REG 6.5 6.85 7 V VBIAS = 8V, no load 6
VCC regulation under load VVCC-REG 6.5 V VBIAS = 8V, IVCC = 35mA 6
VCC UVLO threshold, rising VVCC-UVLO(RISING) 2.75 2.85 2.95 V VCC rising 6
VCC source current limit IVCC-CL 35 105 mA VBIAS = 10V, VVCC = 0V 6
COMP clamp voltage, rising 2.5 2.8 V COMP rising (VUVLO = 2.0V) 7
COMP clamp voltage, falling 1 1.1 V COMP falling 7
EN enable threshold, rising VEN(RISING) 0.4 0.52 0.7 V EN rising 7
EN enable threshold, falling VEN(FALLING) 0.33 0.49 0.63 V EN falling 7
UVLO/SYNC threshold, rising VUVLO(RISING) 1.425 1.5 1.575 V UVLO rising 7
UVLO/SYNC threshold, falling VUVLO(FALLING) 1.37 1.45 1.52 V UVLO falling 7
UVLO hysteresis current IUVLO 4 5 6 uA VUVLO = 1.6V 7
Soft-start current ISS 9 10 11 uA 7
Switching frequency 1 fsw1 85 100 115 kHz RT = 220kΩ 7
Switching frequency 2 fsw2 1980 2200 2420 kHz RT = 9.09kΩ 7
Maximum duty cycle limit 1 DMAX1 80 85 90 % RT = 9.09kΩ 7
Maximum duty cycle limit 2 DMAX2 90 93 96 % RT = 220kΩ 7
Peak slope compensation current ISLOPE 22.5 30 37.5 uA RT = 220kΩ 7
Current limit threshold (CS-PGND) VCLTH 93 100 107 mV 7
FB reference voltage VREF 0.99 1 1.01 V LM5155, LM51551 7
OVP threshold, FB rising (referenced to VREF) VOVTH 107 110 113 % FB rising, referenced to VREF 7
UVLO threshold, FB falling (PGOOD, referenced to VREF) VUVTH 87 90 93 % FB falling, referenced to VREF 7
Thermal shutdown threshold TTSD 175 °C Temperature rising 7
MOSFET driver high-state voltage drop 0.25 V 100mA sink 7
MOSFET driver low-state voltage drop 0.15 V 100mA source 7
SS pull-down switch RDSON 55 Ω 7
PGOOD pull-down switch RDSON 90 Ω 1 mA sink 7
COMP sourcing current 180 uA VCOMP = 1.2V 7
Minimum on-time tON(MIN) 50 ns RT = 9.09kΩ 7
Error amplifier transconductance Gm 2 mA/V 7
Intermittent mode enable period (LM51551) 64 cycles LM51551 intermittent-mode option 7
VCC UVLO hysteresis 0.063 V VCC falling 6
Junction-to-ambient thermal resistance (DSS0012C, WF) RθJA 60.3 °C/W 6
Junction-to-case (top) thermal resistance (DSS0012C, WF) RθJC(top) 60.1 °C/W 6
Junction-to-board thermal resistance (DSS0012C, WF) RθJB 28.8 °C/W 6
Junction-to-case (bottom) thermal resistance (DSS0012C, WF) RθJC(bot) 7.1 °C/W 6

CAD (KiCad official)

  • Symbol: LM51551QDSSRQ1
  • Footprint: Package_SON:WSON-12-1EP_3x2mm_P0.5mm_EP1x2.65
  • 3D model: WSON-12-EP(2x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: lm51551qdssrq1-etched.step / lm51551qdssrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm51551qdssrq1.step / lm51551qdssrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (50 pp, sha256 a8503f9fa4bec785, retrieved 2026-10-05, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF