main
Ray
lm5140qrwgtq1: specified limits as data (metadata.characteristics, 60 rows from the datasheet)
28bc83b
LM5140QRWGTQ1
Texas Instruments · DC-DC Controllers · VQFN-40-EP(6x6)
LM5140QRWGTQ1 from Texas Instruments, in a VQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS2 | input | Channel 2 soft-start ramp node; internal 20-μA source charges external capacitor; pulling below 80 mV disables channel 2 gate driver outputs. |
| 2 | COMP2 | output | Channel 2 transconductance error amplifier output; apply compensation network to set loop response. |
| 3 | FB2 | input | Channel 2 feedback input; connect to VDDA for 5-V output, ground for 8-V fixed output, or external divider for 1.5-15-V adjustable (1.2-V regulation threshold). |
| 4 | CS2 | input | Channel 2 current sense amplifier input; make low-current Kelvin connection to inductor side of sense resistor. |
| 5 | VOUT2 | input | Channel 2 output and current sense amplifier input; connect to load side of channel 2 current sense resistor. |
| 6 | VCCX | input | Optional external 5-V bias supply input; if VCCX > 4.5 V, internally connected to VCC and disables internal regulator; ground if unused; maximum 6.5 V. |
| 7 | PG2 | output | Channel 2 power-good open-collector output; asserts low when VOUT2 falls below 92% or rises above 110% of regulation voltage; 25-μs deglitch filter. |
| 8 | HOL2 | output | Channel 2 high-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 9 | HO2 | output | Channel 2 high-side gate driver turn-on output; sources 3.25-A peak current at HB2 voltage, sinks 4.25 A peak. |
| 10 | SW2 | input | Channel 2 switching node sense input; connect to bootstrap capacitor, source of high-side MOSFET, and drain of low-side MOSFET. |
| 11 | HB2 | output | Channel 2 bootstrap gate driver supply output; charges from VCC through external diode when low-side FET is on; typical voltage HB2 - SW2 = 4.5-5.25 V. |
| 12 | LOL2 | output | Channel 2 low-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 13 | LO2 | output | Channel 2 low-side gate driver turn-on output; sources 3.25-A peak current, sinks 4.25 A peak to PGND. |
| 14 | PGND2 | power_in | Channel 2 power ground return for low-side MOSFET gate driver; connect to board power ground plane. |
| 15 | VCC | power_in | Bias supply input (pins 15 and 16 must be connected together on PCB); 5-V regulated output (4.75-5.25 V typical); 150-mA minimum source limit. |
| 16 | VCC | power_in | Bias supply input (pins 15 and 16 must be connected together on PCB); 5-V regulated output (4.75-5.25 V typical); 150-mA minimum source limit. |
| 17 | PGND1 | power_in | Channel 1 power ground return for low-side MOSFET gate driver; connect to board power ground plane. |
| 18 | LO1 | output | Channel 1 low-side gate driver turn-on output; sources 3.25-A peak current, sinks 4.25 A peak to PGND. |
| 19 | LOL1 | output | Channel 1 low-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 20 | HB1 | output | Channel 1 bootstrap gate driver supply output; charges from VCC through external diode when low-side FET is on; typical voltage HB1 - SW1 = 4.5-5.25 V. |
| 21 | SW1 | input | Channel 1 switching node sense input; connect to bootstrap capacitor, source of high-side MOSFET, and drain of low-side MOSFET. |
| 22 | HO1 | output | Channel 1 high-side gate driver turn-on output; sources 3.25-A peak current at HB1 voltage, sinks 4.25 A peak. |
| 23 | HOL1 | output | Channel 1 high-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 24 | PG1 | output | Channel 1 power-good open-collector output; asserts low when VOUT1 falls below 92% or rises above 110% of regulation voltage; 25-μs deglitch filter. |
| 25 | VIN | power_in | Supply voltage input (3.8-65 V nominal, 70-V absolute maximum); provides input for internal VCC regulator; bypass with quality capacitors to minimize transient ringing. |
| 26 | VOUT1 | input | Channel 1 output and current sense amplifier input; connect to load side of channel 1 current sense resistor. |
| 27 | CS1 | input | Channel 1 current sense amplifier input; make low-current Kelvin connection to inductor side of sense resistor. |
| 28 | FB1 | input | Channel 1 feedback input; connect to VDDA for 3.3-V output, ground for 5-V fixed output, or external divider for 1.5-15-V adjustable (1.2-V regulation threshold). |
| 29 | COMP1 | output | Channel 1 transconductance error amplifier output; apply compensation network to set loop response. |
| 30 | SS1 | input | Channel 1 soft-start ramp node; internal 20-μA source charges external capacitor; pulling below 80 mV disables channel 1 gate driver outputs. |
| 31 | EN1 | input | Channel 1 enable logic input (active high); threshold 2.4 V typical; accepts voltage up to 70 V for wide input range applications. |
| 32 | RES | output | Restart timer output node; external capacitor configures hiccup mode off-time (20-μA internal charging current); connect to VDDA to disable hiccup protection. |
| 33 | DEMB | input | Diode emulation mode control; ground enables diode emulation mode (discontinuous conduction at light load), VDDA enables forced-PWM mode (continuous conduction). |
| 34 | ILSET | input | Current-limit threshold selection pin (latched at power-up); VDDA sets 73-mV limit, ground sets 48-mV limit; ±10% accuracy typical. |
| 35 | AGND | power_in | Analog ground return for internal voltage reference and analog circuits; connect to PGND at single point under IC for low noise. |
| 36 | VDDA | power_in | Internal analog bias regulator output (5-V nominal or 3.3-V in low-power modes); bypass with 100-nF or larger ceramic capacitor to AGND. |
| 37 | OSC | input | Oscillator frequency selection pin (latched at power-up); VDDA selects 2.2-MHz operation, ground selects 440-kHz operation; ±7% frequency tolerance. |
| 38 | SYNIN | input | External synchronization clock input (TTL level); enables internal oscillator sync to external clock; ground if synchronization feature not used. |
| 39 | SYNOUT | output | Synchronization clock output (TTL level); 180° out-of-phase with HO1 gate drive; 50% duty cycle; operates at CLK2 frequency. |
| 40 | EN2 | input | Channel 2 enable logic input (active high); threshold 2.4 V typical; accepts voltage up to 70 V for wide input range applications. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-40-EP(6x6) |
| Category | Power Supply Chip |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (VIN) absolute max | VIN | -0.3 | 70 | V | 5 | ||
| SW1, SW2 to PGND | -0.3 | 70 | V | 5 | |||
| SW1, SW2 to PGND (20 ns transient) | -5 | V | 20 ns transient | 5 | |||
| HB1 to SW1, HB2 to SW2 | -0.3 | 6.5 | V | 5 | |||
| HB1 to SW1, HB2 to SW2 (20 ns transient) | -5 | V | 20 ns transient | 5 | |||
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 | -0.3 | V | 5 | ||||
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 (20 ns transient) | -5 | V | 20 ns transient | 5 | |||
| LO1, LOL1, LO2, LOL2 to PGND | -0.3 | V | 5 | ||||
| LO1, LOL1, LO2, LOL2 to PGND (20 ns transient) | -1.5 | V | 20 ns transient | 5 | |||
| OSC, SS1, SS2, COMP1, COMP2, RES, DEMB, ILSET | -0.3 | V | 5 | ||||
| EN1, EN2 to PGND | -0.3 | 70 | V | 5 | |||
| VCC, VCCX, VDDA, PG1, PG2, FB1, FB2, SYNIN | -0.3 | 6.5 | V | 5 | |||
| VOUT1, VOUT2, CS1, CS2 | -0.3 | 15.5 | V | 5 | |||
| VOUT1 to CS1, VOUT2 to CS2 | -0.3 | 0.3 | V | 5 | |||
| PGND to AGND | -0.3 | 0.3 | V | 5 | |||
| Operating junction temperature | -40 | 150 | °C | 5 | |||
| Storage temperature | Tstg | -40 | 150 | °C | 5 | ||
| ESD human-body model (HBM) | V(ESD) | -2000 | 2000 | V | HBM, per AEC Q100-002 | 5 | |
| ESD charged-device model (CDM), all pins | V(ESD) | -500 | 500 | V | CDM, per AEC Q100-011, all pins | 5 | |
| ESD charged-device model (CDM), corner pins | V(ESD) | -750 | 750 | V | CDM, per AEC Q100-011, corner pins | 5 | |
| Input voltage range | VIN | 3.8 | 65 | V | 6 | ||
| SW1, SW2 to PGND | -0.3 | 65 | V | 6 | |||
| HB1 to SW1, HB2 to SW2 | -0.3 | 5 | 5.25 | V | 6 | ||
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 | -0.3 | V | 6 | ||||
| LO1, LOL1, LO2, LOL2 to PGND | -0.3 | 5 | 5.25 | V | 6 | ||
| FB1, FB2, PG1, PG2, SYNIN, OSC, SS1, SS2, RES, DEMB, VCCX, ILSET | -0.3 | 5 | V | 6 | |||
| EN1, EN2 to PGND | -0.3 | 65 | V | 6 | |||
| VCC, VDDA | -0.3 | 5 | 5.25 | V | 6 | ||
| VOUT1, VOUT2, CS1, CS2 (output voltage range) | 1.5 | 5 | 15 | V | 6 | ||
| SYNOUT output voltage range | VO | -0.3 | 5.25 | V | 6 | ||
| PGND to AGND | -0.3 | 0.3 | V | 6 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 6 | ||
| I(SHUTDOWN) shutdown mode current | I(SHUTDOWN) | 9 | 12.5 | µA | VIN 8 V- 18 V, EN1 = 0 V, EN2 = 0 V, VCCX = 0 V | 7 | |
| VCC regulation voltage | VCC(REG) | 4.75 | 5 | 5.25 | V | VIN = 6 V - 18 V, 0 - 150 mA, VCCX = 0 V | 7 |
| VCC under voltage threshold | VCC(UVLO) | 3.25 | 3.4 | 3.55 | V | VCC rising, VCCX = 0 V | 7 |
| VCC sourcing current limit | ICC(LIM) | 170 | 250 | mA | VCCX = 0 V | 7 | |
| Internal bias supply power (VDDA regulation voltage) | VDDA(REG) | 4.75 | 5 | 5.25 | V | VCCX = 0 V | 7 |
| VDDA under voltage threshold | VDDA(UVLO) | 3.1 | 3.2 | 3.3 | V | VCC rising, VCCX = 0 V | 7 |
| VCCX on threshold | VCCX(ON) | 4.1 | 4.3 | 4.4 | V | VCC rising | 7 |
| Current limit threshold 1 (73 mV setting) | V(CS1) | 66 | 73 | 80 | mV | ILSET = VDDA, Measure from CS to VOUT | 7 |
| Current limit threshold 2 (48 mV setting) | V(CS2) | 44 | 48 | 53 | mV | ILSET = GND, Measure from CS to VOUT | 7 |
| Current sense amplifier gain | 11.4 | 12 | 12.6 | V/V | 7 | ||
| Regulated feedback voltage | 1.19 | 1.2 | 1.21 | V | 8 | ||
| Transconductance amplifier gain (feedback to COMP) | Gm | 1010 | 1200 | µS | Feedback to COMP | 8 | |
| Output voltage regulation, 3.3 V output | 3.273 | 3.3 | 3.327 | V | VIN = 3.8 V - 42 V | 8 | |
| Output voltage regulation, 5 V output | 4.95 | 5 | 5.05 | V | VIN = 5.5 V - 42 V | 8 | |
| Output voltage regulation, 8 V output | 7.92 | 8 | 8.08 | V | VIN = 8.5 V - 42 V | 8 | |
| PG under voltage trip level | PG(UV) | 90 | 92 | 94 | % | Falling with respect to the regulation voltage | 8 |
| PG over voltage trip level | PG(OVP) | 108 | 110 | 112 | % | Rising with respect to the regulation voltage | 8 |
| Soft-start current | ISS | 16 | 22 | 28 | µA | 9 | |
| SYNIN input frequency range, 440 kHz setting | 350 | 550 | kHz | 440 kHz | 9 | ||
| SYNIN input frequency range, 2.2 MHz setting | 1800 | 2600 | kHz | 2.2 MHz | 9 | ||
| Oscillator frequency, 2.2 MHz | 2060 | 2200 | 2340 | kHz | OSC = VDDA, VIN = 8 V -18 V | 9 | |
| Oscillator frequency, 440 kHz | 410 | 440 | 470 | kHz | OSC = GND, VIN = 8 V - 18 V | 9 | |
| Junction-to-ambient thermal resistance | RθJA | 34.8 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 22.8 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 9.5 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 1.3 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 9.4 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 0.3 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LM5140QRWGTQ1 - Footprint:
Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm - 3D model: VQFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
lm5140qrwgtq1-etched.step/lm5140qrwgtq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5140qrwgtq1.step/lm5140qrwgtq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (48 pp, sha256
0d277fa180b6852d, retrieved 2026-09-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM5140QRWGTQ1
**Texas Instruments** · DC-DC Controllers · VQFN-40-EP(6x6)
LM5140QRWGTQ1 from Texas Instruments, in a VQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS2 | input | Channel 2 soft-start ramp node; internal 20-μA source charges external capacitor; pulling below 80 mV disables channel 2 gate driver outputs. |
| 2 | COMP2 | output | Channel 2 transconductance error amplifier output; apply compensation network to set loop response. |
| 3 | FB2 | input | Channel 2 feedback input; connect to VDDA for 5-V output, ground for 8-V fixed output, or external divider for 1.5-15-V adjustable (1.2-V regulation threshold). |
| 4 | CS2 | input | Channel 2 current sense amplifier input; make low-current Kelvin connection to inductor side of sense resistor. |
| 5 | VOUT2 | input | Channel 2 output and current sense amplifier input; connect to load side of channel 2 current sense resistor. |
| 6 | VCCX | input | Optional external 5-V bias supply input; if VCCX > 4.5 V, internally connected to VCC and disables internal regulator; ground if unused; maximum 6.5 V. |
| 7 | PG2 | output | Channel 2 power-good open-collector output; asserts low when VOUT2 falls below 92% or rises above 110% of regulation voltage; 25-μs deglitch filter. |
| 8 | HOL2 | output | Channel 2 high-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 9 | HO2 | output | Channel 2 high-side gate driver turn-on output; sources 3.25-A peak current at HB2 voltage, sinks 4.25 A peak. |
| 10 | SW2 | input | Channel 2 switching node sense input; connect to bootstrap capacitor, source of high-side MOSFET, and drain of low-side MOSFET. |
| 11 | HB2 | output | Channel 2 bootstrap gate driver supply output; charges from VCC through external diode when low-side FET is on; typical voltage HB2 - SW2 = 4.5-5.25 V. |
| 12 | LOL2 | output | Channel 2 low-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 13 | LO2 | output | Channel 2 low-side gate driver turn-on output; sources 3.25-A peak current, sinks 4.25 A peak to PGND. |
| 14 | PGND2 | power_in | Channel 2 power ground return for low-side MOSFET gate driver; connect to board power ground plane. |
| 15 | VCC | power_in | Bias supply input (pins 15 and 16 must be connected together on PCB); 5-V regulated output (4.75-5.25 V typical); 150-mA minimum source limit. |
| 16 | VCC | power_in | Bias supply input (pins 15 and 16 must be connected together on PCB); 5-V regulated output (4.75-5.25 V typical); 150-mA minimum source limit. |
| 17 | PGND1 | power_in | Channel 1 power ground return for low-side MOSFET gate driver; connect to board power ground plane. |
| 18 | LO1 | output | Channel 1 low-side gate driver turn-on output; sources 3.25-A peak current, sinks 4.25 A peak to PGND. |
| 19 | LOL1 | output | Channel 1 low-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 20 | HB1 | output | Channel 1 bootstrap gate driver supply output; charges from VCC through external diode when low-side FET is on; typical voltage HB1 - SW1 = 4.5-5.25 V. |
| 21 | SW1 | input | Channel 1 switching node sense input; connect to bootstrap capacitor, source of high-side MOSFET, and drain of low-side MOSFET. |
| 22 | HO1 | output | Channel 1 high-side gate driver turn-on output; sources 3.25-A peak current at HB1 voltage, sinks 4.25 A peak. |
| 23 | HOL1 | output | Channel 1 high-side gate driver turn-off output; independent source/sink pin for adjustable slew-rate control. |
| 24 | PG1 | output | Channel 1 power-good open-collector output; asserts low when VOUT1 falls below 92% or rises above 110% of regulation voltage; 25-μs deglitch filter. |
| 25 | VIN | power_in | Supply voltage input (3.8-65 V nominal, 70-V absolute maximum); provides input for internal VCC regulator; bypass with quality capacitors to minimize transient ringing. |
| 26 | VOUT1 | input | Channel 1 output and current sense amplifier input; connect to load side of channel 1 current sense resistor. |
| 27 | CS1 | input | Channel 1 current sense amplifier input; make low-current Kelvin connection to inductor side of sense resistor. |
| 28 | FB1 | input | Channel 1 feedback input; connect to VDDA for 3.3-V output, ground for 5-V fixed output, or external divider for 1.5-15-V adjustable (1.2-V regulation threshold). |
| 29 | COMP1 | output | Channel 1 transconductance error amplifier output; apply compensation network to set loop response. |
| 30 | SS1 | input | Channel 1 soft-start ramp node; internal 20-μA source charges external capacitor; pulling below 80 mV disables channel 1 gate driver outputs. |
| 31 | EN1 | input | Channel 1 enable logic input (active high); threshold 2.4 V typical; accepts voltage up to 70 V for wide input range applications. |
| 32 | RES | output | Restart timer output node; external capacitor configures hiccup mode off-time (20-μA internal charging current); connect to VDDA to disable hiccup protection. |
| 33 | DEMB | input | Diode emulation mode control; ground enables diode emulation mode (discontinuous conduction at light load), VDDA enables forced-PWM mode (continuous conduction). |
| 34 | ILSET | input | Current-limit threshold selection pin (latched at power-up); VDDA sets 73-mV limit, ground sets 48-mV limit; ±10% accuracy typical. |
| 35 | AGND | power_in | Analog ground return for internal voltage reference and analog circuits; connect to PGND at single point under IC for low noise. |
| 36 | VDDA | power_in | Internal analog bias regulator output (5-V nominal or 3.3-V in low-power modes); bypass with 100-nF or larger ceramic capacitor to AGND. |
| 37 | OSC | input | Oscillator frequency selection pin (latched at power-up); VDDA selects 2.2-MHz operation, ground selects 440-kHz operation; ±7% frequency tolerance. |
| 38 | SYNIN | input | External synchronization clock input (TTL level); enables internal oscillator sync to external clock; ground if synchronization feature not used. |
| 39 | SYNOUT | output | Synchronization clock output (TTL level); 180° out-of-phase with HO1 gate drive; 50% duty cycle; operates at CLK2 frequency. |
| 40 | EN2 | input | Channel 2 enable logic input (active high); threshold 2.4 V typical; accepts voltage up to 70 V for wide input range applications. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-40-EP(6x6) |
| Category | Power Supply Chip |
| Pins | 41 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (VIN) absolute max | VIN | -0.3 | | 70 | V | | 5 |
| SW1, SW2 to PGND | | -0.3 | | 70 | V | | 5 |
| SW1, SW2 to PGND (20 ns transient) | | -5 | | | V | 20 ns transient | 5 |
| HB1 to SW1, HB2 to SW2 | | -0.3 | | 6.5 | V | | 5 |
| HB1 to SW1, HB2 to SW2 (20 ns transient) | | -5 | | | V | 20 ns transient | 5 |
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 | | -0.3 | | | V | | 5 |
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 (20 ns transient) | | -5 | | | V | 20 ns transient | 5 |
| LO1, LOL1, LO2, LOL2 to PGND | | -0.3 | | | V | | 5 |
| LO1, LOL1, LO2, LOL2 to PGND (20 ns transient) | | -1.5 | | | V | 20 ns transient | 5 |
| OSC, SS1, SS2, COMP1, COMP2, RES, DEMB, ILSET | | -0.3 | | | V | | 5 |
| EN1, EN2 to PGND | | -0.3 | | 70 | V | | 5 |
| VCC, VCCX, VDDA, PG1, PG2, FB1, FB2, SYNIN | | -0.3 | | 6.5 | V | | 5 |
| VOUT1, VOUT2, CS1, CS2 | | -0.3 | | 15.5 | V | | 5 |
| VOUT1 to CS1, VOUT2 to CS2 | | -0.3 | | 0.3 | V | | 5 |
| PGND to AGND | | -0.3 | | 0.3 | V | | 5 |
| Operating junction temperature | | -40 | | 150 | °C | | 5 |
| Storage temperature | Tstg | -40 | | 150 | °C | | 5 |
| ESD human-body model (HBM) | V(ESD) | -2000 | | 2000 | V | HBM, per AEC Q100-002 | 5 |
| ESD charged-device model (CDM), all pins | V(ESD) | -500 | | 500 | V | CDM, per AEC Q100-011, all pins | 5 |
| ESD charged-device model (CDM), corner pins | V(ESD) | -750 | | 750 | V | CDM, per AEC Q100-011, corner pins | 5 |
| Input voltage range | VIN | 3.8 | | 65 | V | | 6 |
| SW1, SW2 to PGND | | -0.3 | | 65 | V | | 6 |
| HB1 to SW1, HB2 to SW2 | | -0.3 | 5 | 5.25 | V | | 6 |
| HO1 to SW1, HOL1 to SW1, HO2 to SW2, HOL2 to SW2 | | -0.3 | | | V | | 6 |
| LO1, LOL1, LO2, LOL2 to PGND | | -0.3 | 5 | 5.25 | V | | 6 |
| FB1, FB2, PG1, PG2, SYNIN, OSC, SS1, SS2, RES, DEMB, VCCX, ILSET | | -0.3 | | 5 | V | | 6 |
| EN1, EN2 to PGND | | -0.3 | | 65 | V | | 6 |
| VCC, VDDA | | -0.3 | 5 | 5.25 | V | | 6 |
| VOUT1, VOUT2, CS1, CS2 (output voltage range) | | 1.5 | 5 | 15 | V | | 6 |
| SYNOUT output voltage range | VO | -0.3 | | 5.25 | V | | 6 |
| PGND to AGND | | -0.3 | | 0.3 | V | | 6 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 6 |
| I(SHUTDOWN) shutdown mode current | I(SHUTDOWN) | | 9 | 12.5 | µA | VIN 8 V- 18 V, EN1 = 0 V, EN2 = 0 V, VCCX = 0 V | 7 |
| VCC regulation voltage | VCC(REG) | 4.75 | 5 | 5.25 | V | VIN = 6 V - 18 V, 0 - 150 mA, VCCX = 0 V | 7 |
| VCC under voltage threshold | VCC(UVLO) | 3.25 | 3.4 | 3.55 | V | VCC rising, VCCX = 0 V | 7 |
| VCC sourcing current limit | ICC(LIM) | | 170 | 250 | mA | VCCX = 0 V | 7 |
| Internal bias supply power (VDDA regulation voltage) | VDDA(REG) | 4.75 | 5 | 5.25 | V | VCCX = 0 V | 7 |
| VDDA under voltage threshold | VDDA(UVLO) | 3.1 | 3.2 | 3.3 | V | VCC rising, VCCX = 0 V | 7 |
| VCCX on threshold | VCCX(ON) | 4.1 | 4.3 | 4.4 | V | VCC rising | 7 |
| Current limit threshold 1 (73 mV setting) | V(CS1) | 66 | 73 | 80 | mV | ILSET = VDDA, Measure from CS to VOUT | 7 |
| Current limit threshold 2 (48 mV setting) | V(CS2) | 44 | 48 | 53 | mV | ILSET = GND, Measure from CS to VOUT | 7 |
| Current sense amplifier gain | | 11.4 | 12 | 12.6 | V/V | | 7 |
| Regulated feedback voltage | | 1.19 | 1.2 | 1.21 | V | | 8 |
| Transconductance amplifier gain (feedback to COMP) | Gm | 1010 | 1200 | | µS | Feedback to COMP | 8 |
| Output voltage regulation, 3.3 V output | | 3.273 | 3.3 | 3.327 | V | VIN = 3.8 V - 42 V | 8 |
| Output voltage regulation, 5 V output | | 4.95 | 5 | 5.05 | V | VIN = 5.5 V - 42 V | 8 |
| Output voltage regulation, 8 V output | | 7.92 | 8 | 8.08 | V | VIN = 8.5 V - 42 V | 8 |
| PG under voltage trip level | PG(UV) | 90 | 92 | 94 | % | Falling with respect to the regulation voltage | 8 |
| PG over voltage trip level | PG(OVP) | 108 | 110 | 112 | % | Rising with respect to the regulation voltage | 8 |
| Soft-start current | ISS | 16 | 22 | 28 | µA | | 9 |
| SYNIN input frequency range, 440 kHz setting | | 350 | | 550 | kHz | 440 kHz | 9 |
| SYNIN input frequency range, 2.2 MHz setting | | 1800 | | 2600 | kHz | 2.2 MHz | 9 |
| Oscillator frequency, 2.2 MHz | | 2060 | 2200 | 2340 | kHz | OSC = VDDA, VIN = 8 V -18 V | 9 |
| Oscillator frequency, 440 kHz | | 410 | 440 | 470 | kHz | OSC = GND, VIN = 8 V - 18 V | 9 |
| Junction-to-ambient thermal resistance | RθJA | | 34.8 | | °C/W | | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 22.8 | | °C/W | | 6 |
| Junction-to-board thermal resistance | RθJB | | 9.5 | | °C/W | | 6 |
| Junction-to-top characterization parameter | ψJT | | 1.3 | | °C/W | | 6 |
| Junction-to-board characterization parameter | ψJB | | 9.4 | | °C/W | | 6 |
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | | 0.3 | | °C/W | | 6 |
## CAD (KiCad official)
- Symbol: `LM5140QRWGTQ1`
- Footprint: `Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm`
- 3D model: VQFN-40-EP(6x6) (KiCad packages3D, STEP)
- 3D model files: `lm5140qrwgtq1-etched.step` / `lm5140qrwgtq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5140qrwgtq1.step` / `lm5140qrwgtq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5140-q1) (48 pp, sha256 `0d277fa180b6852d`, retrieved 2026-09-17, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm5140qrwgtq1-datasheet.pdf)