main
History Download
Ray Publish 0.1.0 90dae38

LM5088QMHX-2

Texas Instruments · DC-DC Controllers · HTSSOP-16-EP

LM5088QMHX-2 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in IC supply voltage input with an operating range of 4.5 V to 75 V.
2 EN input Three-level enable input: below 0.4 V low power state, 0.4 V to 1.2 V standby, above 1.2 V operational; a 5-µA pullup enables the controller if left open, and a divider can set a line undervoltage threshold.
3 SS passive Soft-start pin where an internal 11-µA source charges an external capacitor to set start-up rate, held low in standby, VCC UV and thermal shutdown, and usable for tracking with a voltage below 1.2 V.
4 RAMP passive Ramp control signal where an external capacitor to GND (recommended 100 pF to 2000 pF) sets the ramp slope for emulated current mode control.
5 RT/SYNC input Oscillator frequency set input using a single resistor to GND (50 kHz to 1 MHz) and synchronization input for a higher-frequency external signal through a small coupling capacitor; the RT resistor is required even with external sync.
6 GND power_in Ground return.
7 COMP output Output of the internal error amplifier; the loop compensation network is connected between this pin and the FB pin.
8 FB input Feedback signal from the regulated output, connected to the inverting input of the error amplifier with a 1.205 V regulation threshold.
9 OUT input Output voltage connection; connect directly to the regulated output voltage.
10 RES passive LM5088-2 hiccup mode restart pin where an external capacitor sets the current-limit timing: charged by 50 µA on current limit, HG disabled at 1.2 V, discharged by 1 µA, and normal operation resumes below 0.2 V.
11 CSG input Current sense ground, the low-side reference for the current sense resistor.
12 CS input Current sense input measuring the re-circulating diode current through an external sense resistor and internal sample-and-hold, providing the DC offset for the emulated current ramp.
13 SW passive Switching node; connect to the source terminal of the external MOSFET switch.
14 HG output High-side gate drive output; connect to the gate terminal of the external MOSFET switch.
15 BOOT passive Bootstrap capacitor input; an external capacitor between BOOT and SW biases the MOSFET gate driver and is charged from VCC via an internal diode during switch off-time.
16 VCC power_out Bias regulator output tracking VIN up to 7.8 V typical, requiring a 0.1-µF to 10-µF ceramic capacitor, and accepting an external 8.3 V to 13 V supply to reduce internal power dissipation.
17 EP passive Exposed pad, electrically isolated; must be soldered to the ground plane to reduce thermal resistance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN operating current IBIAS 3.8 5.5 mA VFB = 1.3 V 6
VIN standby current ISTANDBY 2.9 3.6 mA VEN = 1 V 6
VIN shutdown current ISHUTDOWN 15 26 µA VEN = 0 V 6
VCC regulation VVCC(Reg) 7.4 7.8 8.2 V VVCC = open 6
VCC regulation at low VIN VVCC(Reg) 4.3 4.5 V VVIN = 4.5 V, VVCC = open 6
VCC sourcing current limit 30 35 mA VVCC = 0 6
VCC undervoltage lockout threshold VVCC(UV) 3.7 4 4.2 V Positive going VVCC 6
EN shutdown threshold 320 400 480 mV VEN rising 6
EN standby threshold 1.1 1.2 1.3 V VEN rising 6
SS pullup current source 8 11 13 µA VSS = 0 V 6
FB reference voltage VREF 1.187 1.205 1.223 V Measured at FB pin, FB = COMP 6
FB input bias current 18 100 nA VFB = 1.2 V 6
Forced HG off time tHG(OFF) 185 280 365 ns 6
Nominal oscillator frequency 1 fnom1 180 200 220 kHz RRT = 31.6 kΩ 7
Nominal oscillator frequency 2 fnom2 430 500 565 kHz RRT = 11.3 kΩ 7
SYNC pulse width 15 150 ns 7
Cycle-by-cycle sense voltage threshold VCS(TH) 112 120 136 mV VRAMP = 0 V 7
RES threshold upper (rising) Vresup 1.1 1.2 1.3 V VCS = 0.125 7
RES threshold lower (falling) Vresdown 0.1 0.2 0.3 V 7
Charge source current Icharge 40 50 65 µA VCS ≥ 0.125 7
Discharge sink current Idischarge 20 27 34 µA VCS < 0.125 7
Discharge sink current (post fault) Irampdown 0.8 1.2 1.6 µA 7
RAMP current 1 IRAMP1 235 295 345 µA VVIN = 60 V, VOUT = 10 V 7
RAMP current 2 IRAMP2 18 25 30 µA VVIN = 10 V, VOUT = 10 V 7
VOUT bias current 250 µA VOUT = 48 V 7
HG low-state output voltage VOLH 115 215 mV IHG = 100 mA 7
Thermal shutdown temperature TSD 165 °C Junction temperature rising 7
VIN, VOUT to GND 76 V 5
BOOT to GND 90 V 5
SW to GND -2 76 V 5
VCC to GND -0.3 16 V 5
HG to SW -0.3 V max is BOOT + 0.3 V 5
EN to GND 14 V 5
BOOT to SW -0.3 16 V 5
CS, CSG to GND -0.3 0.3 V 5
All other inputs to GND -0.3 7 V 5
Junction temperature TJ 150 °C 5
Storage temperature Tstg -65 150 °C 5
ESD HBM (LM5088-Q1) V(ESD) -2000 2000 V per AEC Q100-002 5
ESD CDM (LM5088-Q1) V(ESD) -750 750 V per AEC Q100-011, all pins 5
VIN voltage 4.5 75 V 5
VCC voltage (externally supplied) 8.3 13 V 5
Operation junction temperature TJ -40 125 °C 5
Junction-to-ambient thermal resistance RθJA 40 °C/W PWP 16 pins 6
Junction-to-case (bottom) thermal resistance RθJC(bot) 6 °C/W PWP 16 pins 6

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper power ground connections (CSS, RT, and CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to top-side copper area covering the entire underside of the device. 34

CAD (KiCad official)

  • Symbol: LM5088QMHX-2
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm5088qmhx-2-etched.step / lm5088qmhx-2-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5088qmhx-2.step / lm5088qmhx-2.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 7879d2691313142d, retrieved 2026-10-31, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF