3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLM5088QMHX-2
Texas Instruments · DC-DC Controllers · HTSSOP-16-EP
LM5088QMHX-2 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | IC supply voltage input with an operating range of 4.5 V to 75 V. |
| 2 | EN | input | Three-level enable input: below 0.4 V low power state, 0.4 V to 1.2 V standby, above 1.2 V operational; a 5-µA pullup enables the controller if left open, and a divider can set a line undervoltage threshold. |
| 3 | SS | passive | Soft-start pin where an internal 11-µA source charges an external capacitor to set start-up rate, held low in standby, VCC UV and thermal shutdown, and usable for tracking with a voltage below 1.2 V. |
| 4 | RAMP | passive | Ramp control signal where an external capacitor to GND (recommended 100 pF to 2000 pF) sets the ramp slope for emulated current mode control. |
| 5 | RT/SYNC | input | Oscillator frequency set input using a single resistor to GND (50 kHz to 1 MHz) and synchronization input for a higher-frequency external signal through a small coupling capacitor; the RT resistor is required even with external sync. |
| 6 | GND | power_in | Ground return. |
| 7 | COMP | output | Output of the internal error amplifier; the loop compensation network is connected between this pin and the FB pin. |
| 8 | FB | input | Feedback signal from the regulated output, connected to the inverting input of the error amplifier with a 1.205 V regulation threshold. |
| 9 | OUT | input | Output voltage connection; connect directly to the regulated output voltage. |
| 10 | RES | passive | LM5088-2 hiccup mode restart pin where an external capacitor sets the current-limit timing: charged by 50 µA on current limit, HG disabled at 1.2 V, discharged by 1 µA, and normal operation resumes below 0.2 V. |
| 11 | CSG | input | Current sense ground, the low-side reference for the current sense resistor. |
| 12 | CS | input | Current sense input measuring the re-circulating diode current through an external sense resistor and internal sample-and-hold, providing the DC offset for the emulated current ramp. |
| 13 | SW | passive | Switching node; connect to the source terminal of the external MOSFET switch. |
| 14 | HG | output | High-side gate drive output; connect to the gate terminal of the external MOSFET switch. |
| 15 | BOOT | passive | Bootstrap capacitor input; an external capacitor between BOOT and SW biases the MOSFET gate driver and is charged from VCC via an internal diode during switch off-time. |
| 16 | VCC | power_out | Bias regulator output tracking VIN up to 7.8 V typical, requiring a 0.1-µF to 10-µF ceramic capacitor, and accepting an external 8.3 V to 13 V supply to reduce internal power dissipation. |
| 17 | EP | passive | Exposed pad, electrically isolated; must be soldered to the ground plane to reduce thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN operating current | IBIAS | 3.8 | 5.5 | mA | VFB = 1.3 V | 6 | |
| VIN standby current | ISTANDBY | 2.9 | 3.6 | mA | VEN = 1 V | 6 | |
| VIN shutdown current | ISHUTDOWN | 15 | 26 | µA | VEN = 0 V | 6 | |
| VCC regulation | VVCC(Reg) | 7.4 | 7.8 | 8.2 | V | VVCC = open | 6 |
| VCC regulation at low VIN | VVCC(Reg) | 4.3 | 4.5 | V | VVIN = 4.5 V, VVCC = open | 6 | |
| VCC sourcing current limit | 30 | 35 | mA | VVCC = 0 | 6 | ||
| VCC undervoltage lockout threshold | VVCC(UV) | 3.7 | 4 | 4.2 | V | Positive going VVCC | 6 |
| EN shutdown threshold | 320 | 400 | 480 | mV | VEN rising | 6 | |
| EN standby threshold | 1.1 | 1.2 | 1.3 | V | VEN rising | 6 | |
| SS pullup current source | 8 | 11 | 13 | µA | VSS = 0 V | 6 | |
| FB reference voltage | VREF | 1.187 | 1.205 | 1.223 | V | Measured at FB pin, FB = COMP | 6 |
| FB input bias current | 18 | 100 | nA | VFB = 1.2 V | 6 | ||
| Forced HG off time | tHG(OFF) | 185 | 280 | 365 | ns | 6 | |
| Nominal oscillator frequency 1 | fnom1 | 180 | 200 | 220 | kHz | RRT = 31.6 kΩ | 7 |
| Nominal oscillator frequency 2 | fnom2 | 430 | 500 | 565 | kHz | RRT = 11.3 kΩ | 7 |
| SYNC pulse width | 15 | 150 | ns | 7 | |||
| Cycle-by-cycle sense voltage threshold | VCS(TH) | 112 | 120 | 136 | mV | VRAMP = 0 V | 7 |
| RES threshold upper (rising) | Vresup | 1.1 | 1.2 | 1.3 | V | VCS = 0.125 | 7 |
| RES threshold lower (falling) | Vresdown | 0.1 | 0.2 | 0.3 | V | 7 | |
| Charge source current | Icharge | 40 | 50 | 65 | µA | VCS ≥ 0.125 | 7 |
| Discharge sink current | Idischarge | 20 | 27 | 34 | µA | VCS < 0.125 | 7 |
| Discharge sink current (post fault) | Irampdown | 0.8 | 1.2 | 1.6 | µA | 7 | |
| RAMP current 1 | IRAMP1 | 235 | 295 | 345 | µA | VVIN = 60 V, VOUT = 10 V | 7 |
| RAMP current 2 | IRAMP2 | 18 | 25 | 30 | µA | VVIN = 10 V, VOUT = 10 V | 7 |
| VOUT bias current | 250 | µA | VOUT = 48 V | 7 | |||
| HG low-state output voltage | VOLH | 115 | 215 | mV | IHG = 100 mA | 7 | |
| Thermal shutdown temperature | TSD | 165 | °C | Junction temperature rising | 7 | ||
| VIN, VOUT to GND | 76 | V | 5 | ||||
| BOOT to GND | 90 | V | 5 | ||||
| SW to GND | -2 | 76 | V | 5 | |||
| VCC to GND | -0.3 | 16 | V | 5 | |||
| HG to SW | -0.3 | V | max is BOOT + 0.3 V | 5 | |||
| EN to GND | 14 | V | 5 | ||||
| BOOT to SW | -0.3 | 16 | V | 5 | |||
| CS, CSG to GND | -0.3 | 0.3 | V | 5 | |||
| All other inputs to GND | -0.3 | 7 | V | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| ESD HBM (LM5088-Q1) | V(ESD) | -2000 | 2000 | V | per AEC Q100-002 | 5 | |
| ESD CDM (LM5088-Q1) | V(ESD) | -750 | 750 | V | per AEC Q100-011, all pins | 5 | |
| VIN voltage | 4.5 | 75 | V | 5 | |||
| VCC voltage (externally supplied) | 8.3 | 13 | V | 5 | |||
| Operation junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 40 | °C/W | PWP 16 pins | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 6 | °C/W | PWP 16 pins | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | power ground connections (CSS, RT, and CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to top-side copper area covering the entire underside of the device. | 34 |
CAD (KiCad official)
- Symbol:
LM5088QMHX-2 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm5088qmhx-2-etched.step/lm5088qmhx-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5088qmhx-2.step/lm5088qmhx-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
7879d2691313142d, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).