LM5060QDGSRQ1

{
  "slug": "lm5060qdgsrq1",
  "version": "0.1.0",
  "type": "component",
  "description": "Texas Instruments Surge Protection Devices (SPDs), VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "circuit protection",
    "lm5060qdgsrq1",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "lm5060qdgsrq1.kicad_sym",
    "lm5060qdgsrq1.kicad_mod",
    "lm5060qdgsrq1.glb",
    "lm5060qdgsrq1.step",
    "lm5060qdgsrq1.lbr",
    "docs/hero.png",
    "docs/lm5060qdgsrq1-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "lm5060qdgsrq1-hero.glb",
    "lm5060qdgsrq1-hero.overlay.json"
  ],
  "component": {
    "mpn": "LM5060QDGSRQ1",
    "manufacturer": "Texas Instruments",
    "package": "VSSOP-10-0.5mm",
    "pin_count": 10,
    "category": "Circuit Protection",
    "subcategory": "Surge Protection Devices (SPDs)",
    "datasheet": "https://www.ti.com/cn/lit/gpn/lm5060-q1",
    "parts": {
      "symbol": "lm5060qdgsrq1.kicad_sym",
      "footprint": "lm5060qdgsrq1.kicad_mod",
      "model_3d": "lm5060qdgsrq1-hero.glb",
      "model_3d_plain": "lm5060qdgsrq1.glb",
      "model_3d_step": "lm5060qdgsrq1-etched.step",
      "model_3d_step_plain": "lm5060qdgsrq1.step",
      "lbr": "lm5060qdgsrq1.lbr"
    },
    "distributor_links": {
      "lcsc": "C2677037",
      "digikey": "296-51307-2-ND",
      "mouser": "595-LM5060QDGSRQ1"
    },
    "distributor_check": {
      "checked_at": "2026-10-08T00:57:57Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "296-51307-2-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "595-LM5060QDGSRQ1",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "SENSE",
        "type": "input",
        "description": "Input voltage sense pin where a 16 µA typical constant current sink flows through an external resistor to set the threshold for VDS fault detection."
      },
      {
        "number": "2",
        "name": "VIN",
        "type": "power_in",
        "description": "Supply voltage input with an operating range of 5.5 V to 65 V; the internal power-on-reset typically becomes active above 5.1 V, and a small ceramic bypass capacitor close to this pin is recommended."
      },
      {
        "number": "3",
        "name": "OVP",
        "type": "input",
        "description": "Over-voltage comparator input that pulls GATE low when the pin exceeds the typical 2.0 V threshold without latching off, and normal operation resumes when it falls below typically 1.76 V."
      },
      {
        "number": "4",
        "name": "UVLO",
        "type": "input",
        "description": "Under-voltage lockout comparator input that releases the GATE pull-down above typically 1.6 V, and includes a 5.5 µA typical current sink that holds it low when open."
      },
      {
        "number": "5",
        "name": "EN",
        "type": "input",
        "description": "Enable input where a voltage below 0.8 V switches the device to low-current shutdown and a voltage above 2.0 V enables the internal bias and UVLO comparator, with a 6 µA typical sink holding it low when open."
      },
      {
        "number": "6",
        "name": "GND",
        "type": "power_in",
        "description": "Circuit ground for the device."
      },
      {
        "number": "7",
        "name": "TIMER",
        "type": "bidirectional",
        "description": "Timing capacitor pin that sets the VDS fault detection delay; when it exceeds the 2.0 V threshold the MOSFET is latched off, and the absolute maximum rating to GND is 7 V."
      },
      {
        "number": "8",
        "name": "nPGD",
        "type": "output",
        "description": "Open-drain fault status output that indicates a VDS fault when high, with the datasheet recommending the low-state sink current be limited below 5 mA."
      },
      {
        "number": "9",
        "name": "OUT",
        "type": "input",
        "description": "Output voltage sense pin connected to the external MOSFET source, used internally to detect VDS and VGS conditions."
      },
      {
        "number": "10",
        "name": "GATE",
        "type": "output",
        "description": "Gate drive output for the external N-channel MOSFET, charged by a 24 µA typical constant current source and clamped by an internal zener typically 16.8 V above the OUT pin."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: Package and ordering confirmed: the orderable addendum (page 34) lists LM5060QDGSRQ1 as VSSOP (DGS),; The package hint says VSSOP-10-0.5mm, but the supplied text does not state the 0.5 mm lead pitch. It; Pin 7 TIMER is labelled I/O in the datasheet and mapped to KiCad bidirectional. Pin 8 nPGD is labell"
        ],
        "pages_sent": 11,
        "cost_usd": 0.07,
        "at": "2026-10-08T00:57:39"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/lm5060-q1",
        "pages": 41,
        "sha256": "38a3fbe1f0f97004",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 10,
        "described": 10,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "lm5060qdgsrq1.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          3.0,
          1.1
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "b8f88eac3ce221c2ccb0b5048f9ad49c2ef4af148f8ae50c4e232e357683f547",
        "checked": "2026-10-08",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "lm5060qdgsrq1-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          3.0,
          1.1
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "11fac9b6973cc8646d2473347a58bda1de31de8abf6bac2a6221bf2dd6b0f9a7",
        "checked": "2026-10-08",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}