Generated by kicad-footprint-generator · KiCad file format 20260206
LM5033SDX
Texas Instruments · DC-DC Controllers · WSON-10-EP(4x4)
LM5033SDX from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input to the start-up regulator, with an input range of 15 V to 90 V and transient capability to 100 V. |
| 2 | REF | output | Sink-only output that requires an external pullup resistor and can serve as a 2.5-V precision output reference for external circuitry. |
| 3 | COMP | input | Feedback input to the inverting input of the PWM comparator through a 3:1 divider, with duty cycle increasing as the voltage rises and an internal 5-kΩ pullup to 5.2 V. |
| 4 | VCC | power_in | 9.6-V output of the internal high-voltage series pass regulator that can be overdriven by an external 10 V to 15 V source to shut down the internal regulator, with an internal diode connecting VCC to VIN. |
| 5 | OUT1 | output | Alternating output gate driver that can source and sink 1.5 A. |
| 6 | OUT2 | output | Alternating output gate driver that can source and sink 1.5 A. |
| 7 | GND | power_in | Ground connection; external ground connections must be made with care for optimum performance. |
| 8 | CS | input | Current-sense input for current limit detection; if the voltage exceeds 0.5 V the outputs are disabled and the SS pin is discharged to ground. |
| 9 | RT/SYNC | input | Oscillator timing resistor pin, where an external resistor to ground sets the oscillator frequency, that also accepts AC-coupled synchronization pulses. |
| 10 | SS | input | Soft-start pin with an internal 10-µA current source and an external capacitor setting the soft-start timing; pulling it below 0.5 V disables the output drivers. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | -0.3 | 100 | V | 4 | |||
| VCC to GND | -0.3 | 16 | V | 4 | |||
| RT/SYNC to GND | -0.3 | 5.5 | V | 4 | |||
| COMP, CS, and SS to GND | -0.3 | 7 | V | 4 | |||
| Maximum junction temperature | TJ(MAX) | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage | VIN | 15 | 99 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| VCC voltage | VCCReg | 9.2 | 9.6 | 10 | V | VCC is open | 5 |
| VCC current limit | ICC(OUT) | 20 | 34 | mA | OUT1 and OUT2 disabled, extended supply to VCC disconnected | 5 | |
| Startup regulator current into VIN | IIN | 150 | 500 | µA | Normal operation, VIN = 90 V | 5 | |
| Startup regulator current into VIN (extended VCC supply disconnected) | IIN | 7 | mA | Extended VCC supply disconnected, output load = 1800 pF | 5 | ||
| Startup regulator current into VIN (VSS = 0 V) | IIN | 3 | mA | VSS = 0 V | 5 | ||
| UVT hysteresis (decreasing VCC) | 2.3 | 2.8 | 3.3 | V | 5 | ||
| Supply current from external source to VCC | ICC(IN) | 2 | 3 | mA | VSS = 0 V | 5 | |
| Supply current from external source to VCC | ICC(IN) | 7 | mA | SS is open, output load = 1800 pF | 5 | ||
| VREF output voltage | VREF | 2.44 | 2.5 | 2.56 | V | REF sink current = 5 mA | 5 |
| REF current sink capability | 5 | 13 | mA | 5 | |||
| CS threshold voltage | 0.45 | 0.5 | 0.55 | V | 5 | ||
| CS delay to output | 30 | ns | VCS taken from zero to 0.6 V, time for VOUT1 or VOUT2 to fall to 90% of VCC, CLOAD = 0 at OUT1 and OUT2 | 5 | |||
| Current sink capability (clocked) | 3 | 6 | mA | VCS ≤ 0.3 V | 5 | ||
| Soft-start current source | 7 | 10 | 13 | µA | 5 | ||
| Soft-start to COMP offset | 0.25 | 0.5 | 0.75 | V | 5 | ||
| Internal frequency | FS1 | 175 | 200 | 225 | kHz | RT = 26.7 kΩ | 5 |
| Sync threshold | VSYNC | 3.2 | 3.8 | V | 5 | ||
| Open circuit voltage (COMP) | 4.2 | 5.2 | 6.2 | V | 5 | ||
| Short circuit current (COMP) | 0.6 | 1.1 | 1.5 | mA | VCOMP = 0 V | 5 | |
| Minimum duty cycle at OUT1 and OUT2 | 0 | % | VCOMP = 0 V | 5 | |||
| Deadtime | tD | 85 | 135 | 185 | ns | CLOAD = 0 at OUT1 and OUT2, time measured from 10% of falling output to 10% of rising output | 5 |
| Output low voltage | 0.25 | 0.75 | V | IOUT = 100 mA (sink) | 5 | ||
| Maximum source current | 1.5 | A | 5 | ||||
| Maximum sink current | 1.5 | A | 5 | ||||
| Junction-to-ambient thermal resistance | RθJA | 38.1 | °C/W | WSON (DPR) 10-pin column | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 36.7 | °C/W | WSON (DPR) 10-pin column | 4 | ||
| Junction-to-board thermal resistance | RθJB | 15.2 | °C/W | WSON (DPR) 10-pin column | 4 | ||
| Junction-to-top characterization parameter | ψJT | 0.3 | °C/W | WSON (DPR) 10-pin column | 4 | ||
| Junction-to-board characterization parameter | ψJB | 15.5 | °C/W | WSON (DPR) 10-pin column | 4 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.7 | °C/W | WSON (DPR) 10-pin column | 4 |
CAD (KiCad official)
- Symbol:
LM5033SDX - Footprint:
Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm - 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lm5033sdx-etched.step/lm5033sdx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5033sdx.step/lm5033sdx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (28 pp, sha256
0c354dacbb795bad, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).