Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM5033SDX

Texas Instruments · DC-DC Controllers · WSON-10-EP(4x4)

LM5033SDX from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input to the start-up regulator, with an input range of 15 V to 90 V and transient capability to 100 V.
2 REF output Sink-only output that requires an external pullup resistor and can serve as a 2.5-V precision output reference for external circuitry.
3 COMP input Feedback input to the inverting input of the PWM comparator through a 3:1 divider, with duty cycle increasing as the voltage rises and an internal 5-kΩ pullup to 5.2 V.
4 VCC power_in 9.6-V output of the internal high-voltage series pass regulator that can be overdriven by an external 10 V to 15 V source to shut down the internal regulator, with an internal diode connecting VCC to VIN.
5 OUT1 output Alternating output gate driver that can source and sink 1.5 A.
6 OUT2 output Alternating output gate driver that can source and sink 1.5 A.
7 GND power_in Ground connection; external ground connections must be made with care for optimum performance.
8 CS input Current-sense input for current limit detection; if the voltage exceeds 0.5 V the outputs are disabled and the SS pin is discharged to ground.
9 RT/SYNC input Oscillator timing resistor pin, where an external resistor to ground sets the oscillator frequency, that also accepts AC-coupled synchronization pulses.
10 SS input Soft-start pin with an internal 10-µA current source and an external capacitor setting the soft-start timing; pulling it below 0.5 V disables the output drivers.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-10-EP(4x4)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to GND -0.3 100 V 4
VCC to GND -0.3 16 V 4
RT/SYNC to GND -0.3 5.5 V 4
COMP, CS, and SS to GND -0.3 7 V 4
Maximum junction temperature TJ(MAX) 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input voltage VIN 15 99 V 4
Operating junction temperature TJ -40 125 °C 4
VCC voltage VCCReg 9.2 9.6 10 V VCC is open 5
VCC current limit ICC(OUT) 20 34 mA OUT1 and OUT2 disabled, extended supply to VCC disconnected 5
Startup regulator current into VIN IIN 150 500 µA Normal operation, VIN = 90 V 5
Startup regulator current into VIN (extended VCC supply disconnected) IIN 7 mA Extended VCC supply disconnected, output load = 1800 pF 5
Startup regulator current into VIN (VSS = 0 V) IIN 3 mA VSS = 0 V 5
UVT hysteresis (decreasing VCC) 2.3 2.8 3.3 V 5
Supply current from external source to VCC ICC(IN) 2 3 mA VSS = 0 V 5
Supply current from external source to VCC ICC(IN) 7 mA SS is open, output load = 1800 pF 5
VREF output voltage VREF 2.44 2.5 2.56 V REF sink current = 5 mA 5
REF current sink capability 5 13 mA 5
CS threshold voltage 0.45 0.5 0.55 V 5
CS delay to output 30 ns VCS taken from zero to 0.6 V, time for VOUT1 or VOUT2 to fall to 90% of VCC, CLOAD = 0 at OUT1 and OUT2 5
Current sink capability (clocked) 3 6 mA VCS ≤ 0.3 V 5
Soft-start current source 7 10 13 µA 5
Soft-start to COMP offset 0.25 0.5 0.75 V 5
Internal frequency FS1 175 200 225 kHz RT = 26.7 kΩ 5
Sync threshold VSYNC 3.2 3.8 V 5
Open circuit voltage (COMP) 4.2 5.2 6.2 V 5
Short circuit current (COMP) 0.6 1.1 1.5 mA VCOMP = 0 V 5
Minimum duty cycle at OUT1 and OUT2 0 % VCOMP = 0 V 5
Deadtime tD 85 135 185 ns CLOAD = 0 at OUT1 and OUT2, time measured from 10% of falling output to 10% of rising output 5
Output low voltage 0.25 0.75 V IOUT = 100 mA (sink) 5
Maximum source current 1.5 A 5
Maximum sink current 1.5 A 5
Junction-to-ambient thermal resistance RθJA 38.1 °C/W WSON (DPR) 10-pin column 4
Junction-to-case (top) thermal resistance RθJC(top) 36.7 °C/W WSON (DPR) 10-pin column 4
Junction-to-board thermal resistance RθJB 15.2 °C/W WSON (DPR) 10-pin column 4
Junction-to-top characterization parameter ψJT 0.3 °C/W WSON (DPR) 10-pin column 4
Junction-to-board characterization parameter ψJB 15.5 °C/W WSON (DPR) 10-pin column 4
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.7 °C/W WSON (DPR) 10-pin column 4

CAD (KiCad official)

  • Symbol: LM5033SDX
  • Footprint: Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm
  • 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lm5033sdx-etched.step / lm5033sdx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm5033sdx.step / lm5033sdx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (28 pp, sha256 0c354dacbb795bad, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF