3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM5033SD
Texas Instruments · DC-DC Controllers · WSON-10-EP(4x4)
LM5033SD from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input to the start-up regulator, with input range from 15 V to 90 V and transient capability to 100 V. |
| 2 | REF | output | Sink-only output that requires an external pullup resistor and can be used as a 2.5-V precision output reference for external circuitry. |
| 3 | COMP | input | Feedback to the inverting input of the PWM comparator through a 3:1 divider, with duty cycle increasing as pin voltage increases and an internal 5-kΩ pullup to 5.2 V. |
| 4 | VCC | power_in | 9.6-V output from the internal high-voltage series pass regulator; an external 10 V to 15 V can be applied to shut down the internal regulator, and an internal diode connects VCC to VIN. |
| 5 | OUT1 | output | Alternating output gate driver that can source and sink 1.5 A. |
| 6 | OUT2 | output | Alternating output gate driver that can source and sink 1.5 A. |
| 7 | GND | power_in | Ground connection; external ground connections must be made with care for optimum performance. |
| 8 | CS | input | Current sense input for current limit detection; if the voltage exceeds 0.5 V the outputs are disabled and the SS pin is discharged to ground. |
| 9 | RT/SYNC | input | Oscillator timing resistor pin where an external resistor to ground sets the frequency, and it also accepts AC-coupled synchronization pulses from an external source. |
| 10 | SS | input | Soft-start pin where an internal 10-µA current source and external capacitor set the timing, and which can be pulled below 0.5 V to disable the output drivers. |
| 11 | EP | passive | Exposed die attach pad on the WSON package that must be connected to a PCB thermal pad at ground potential. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WSON-10-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC voltage | VCCReg | 9.2 | 9.6 | 10 | V | VCC is open | 5 |
| VCC current limit | ICC(OUT) | 20 | 34 | mA | OUT1 and OUT2 disabled, extended supply to VCC disconnected | 5 | |
| Startup regulator current into VIN | IIN | 150 | 500 | µA | Normal operation, VIN = 90 V | 5 | |
| UVT hysteresis (decreasing VCC) | UVT | 2.3 | 2.8 | 3.3 | V | 5 | |
| Supply current from external source to VCC | ICC(IN) | 2 | 3 | mA | VSS = 0 V | 5 | |
| Reference output voltage | VREF | 2.44 | 2.5 | 2.56 | V | REF sink current = 5 mA | 5 |
| REF current sink capability | 5 | 13 | mA | 5 | |||
| CS threshold voltage | 0.45 | 0.5 | 0.55 | V | 5 | ||
| CS current sink capability (clocked) | 3 | 6 | mA | VCS ≤ 0.3 V | 5 | ||
| Soft-start current source | 7 | 10 | 13 | µA | 5 | ||
| Soft-start to COMP offset | 0.25 | 0.5 | 0.75 | V | 5 | ||
| Internal frequency | FS1 | 175 | 200 | 225 | kHz | RT = 26.7 kΩ | 5 |
| COMP open circuit voltage | 4.2 | 5.2 | 6.2 | V | 5 | ||
| COMP short circuit current | 0.6 | 1.1 | 1.5 | mA | VCOMP = 0 V | 5 | |
| Deadtime | tD | 85 | 135 | 185 | ns | CLOAD = 0 at OUT1 and OUT2, time measured from 10% of falling output to 10% of rising output | 5 |
| Output low voltage | 0.25 | 0.75 | V | IOUT = 100 mA (sink) | 5 | ||
| VIN to GND | VIN | -0.3 | 100 | V | 4 | ||
| VCC to GND | VCC | -0.3 | 16 | V | 4 | ||
| RT/SYNC to GND | -0.3 | 5.5 | V | 4 | |||
| COMP, CS, and SS to GND | -0.3 | 7 | V | 4 | |||
| Maximum junction temperature | TJ(MAX) | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Input voltage | VIN | 15 | 99 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 38.1 | °C/W | DPR (WSON) 10 pins | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 36.7 | °C/W | DPR (WSON) 10 pins | 4 | ||
| Junction-to-board thermal resistance | RθJB | 15.2 | °C/W | DPR (WSON) 10 pins | 4 | ||
| Junction-to-top characterization parameter | ψJT | 0.3 | °C/W | DPR (WSON) 10 pins | 4 | ||
| Junction-to-board characterization parameter | ψJB | 15.5 | °C/W | DPR (WSON) 10 pins | 4 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.7 | °C/W | DPR (WSON) 10 pins | 4 | ||
| CS delay to output | 30 | ns | VCS taken from zero to 0.6 V, time for VOUT1 or VOUT2 to fall to 90% of VCC, CLOAD = 0 at OUT1 and OUT2 | 5 | |||
| Internal frequency | FS2 | 600 | kHz | RT = 8.2 kΩ | 5 | ||
| Rise time | 16 | ns | CLOAD = 1 nF | 5 | |||
| Fall time | 16 | ns | CLOAD = 1 nF | 5 | |||
| Shutdown temperature | tSD | 165 | °C | 5 | |||
| Shutdown temperature hysteresis | 15 | °C | 5 |
CAD (KiCad official)
- Symbol:
LM5033SD - Footprint:
Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm - 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lm5033sd-etched.step/lm5033sd-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5033sd.step/lm5033sd.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (28 pp, sha256
0c354dacbb795bad, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).