3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM43603PWP
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM43603PWP from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switching output internally connected to both power MOSFETs, swinging between 0 V and VIN, that connects to the power inductor. |
| 2 | SW | output | Switching output internally connected to both power MOSFETs, swinging between 0 V and VIN, that connects to the power inductor. |
| 3 | CBOOT | power_in | Bootstrap capacitor connection for high-side gate driver charged from SW with a maximum voltage rating of 5.5 V relative to SW. |
| 4 | VCC | power_out | Internal bias supply output rated to 3.6 V maximum that requires bypass capacitor to AGND and must never be shorted to ground during operation. |
| 5 | BIAS | power_in | Optional external LDO supply input accepting 3.3 V to 28 V (or external 3.3/5 V rail) with 1-10 µF bypass capacitor when used, or tie to ground when not used. |
| 6 | SYNC | input | Clock input to synchronize switching action to external clock (−0.3 V to 5.5 V) with proper high-speed termination required to prevent ringing. |
| 7 | RT | input | Frequency programming resistor connection to AGND that programs switching frequency from 200 kHz to 2.2 MHz (default 500 kHz when floating). |
| 8 | PGOOD | tri_state | Open-drain power-good flag output rated to 15 V maximum requiring 10 kΩ to 100 kΩ pullup resistor to logic rail ≤ 12 V. |
| 9 | FB | input | Feedback sense input pin (−0.3 V to 1.1 V) connected to resistor divider for output voltage setting that must not be shorted to ground. |
| 10 | AGND | power_in | Analog ground reference for internal references and logic that requires low-impedance connection to system ground and PAD. |
| 11 | SS/TRK | input | Soft-start control pin that can be left floating for 4.1 ms internal ramp, connected to capacitor to extend ramp, or driven by external voltage for tracking. |
| 12 | EN | input | Enable input (high = ON, low = OFF) for regulator and internal LDO that must connect to VIN, divider, or external logic source and never float. |
| 13 | VIN | power_in | Supply input to internal LDO and high-side power FET with operating range 3.5 V to 36 V (absolute maximum 42 V) requiring connection to power supply and bypass capacitors. |
| 14 | VIN | power_in | Supply input to internal LDO and high-side power FET with operating range 3.5 V to 36 V (absolute maximum 42 V) requiring connection to power supply and bypass capacitors. |
| 15 | PGND | power_in | Power ground connected internally to low-side power FET that establishes return path for power and requires connection to system ground, PAD, and ground of CIN/COUT. |
| 16 | PGND | power_in | Power ground connected internally to low-side power FET that establishes return path for power and requires connection to system ground, PAD, and ground of CIN/COUT. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to PGND | -0.3 | 42 | V | At maximum duty cycle of 0.01% | 5 | ||
| EN to PGND | -0.3 | V | 5 | ||||
| FB, RT, SS/TRK to AGND | -0.3 | 3.6 | V | 5 | |||
| PGOOD to AGND | -0.3 | 15 | V | 5 | |||
| SYNC to AGND | -0.3 | 5.5 | V | 5 | |||
| BIAS to AGND | -0.3 | V | 5 | ||||
| AGND to PGND | -0.3 | 0.3 | V | 5 | |||
| SW to PGND | -0.3 | V | 5 | ||||
| SW to PGND transient | -3.5 | 42 | V | less than 10ns transients | 5 | ||
| CBOOT to SW | -0.3 | 5.5 | V | 5 | |||
| VCC to AGND | -0.3 | 3.6 | V | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| VIN to PGND | 3.5 | 36 | V | 5 | |||
| EN | -0.3 | V | 5 | ||||
| FB | -0.3 | 1.1 | V | 5 | |||
| PGOOD | -0.3 | 12 | V | 5 | |||
| BIAS input not used | -0.3 | 0.3 | V | BIAS input not used | 5 | ||
| BIAS input used | 3.3 | V | BIAS input used | 5 | |||
| AGND to PGND | -0.1 | 0.1 | V | 5 | |||
| Output Voltage | VOUT | 1 | 28 | V | 5 | ||
| Output Current | IOUT | 0 | 3 | A | 5 | ||
| Operating junction temperature range | TJ | -40 | 125 | °C | 5 | ||
| Shutdown quiescent current | ISHDN | 1.2 | 3.1 | µA | VEN = 0 V | 6 | |
| Operating quiescent current (non-switching) from VIN | IQ-NONSW | 5 | 10 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 6 | |
| Operating quiescent current (non-switching) from external VBIAS | IBIAS-NONSW | 85 | 130 | µA | VEN = 3.3 V; VFB = 1.5 V; VBIAS = 3.4 V external | 6 | |
| Enable input leakage current | ILKG-EN | 0.8 | 1.75 | µA | VEN = 3.3 V | 6 | |
| Precision enable level for switching and regulator output | VEN-VOUT-H | 2 | 2.2 | 2.42 | V | VENABLE high level | 6 |
| Internal LDO input change over threshold to BIAS (VBIAS rising threshold) | VBIAS-ON | 2.94 | 3.15 | V | VBIAS rising threshold | 6 | |
| Feedback voltage | VFB | 1.004 | 1.011 | 1.018 | V | TJ = 25 ºC | 7 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.026 | V | TJ = -40 ºC to 85 ºC | 7 |
| Feedback voltage | VFB | 0.994 | 1.011 | 1.03 | V | TJ = -40 ºC to 125 ºC | 7 |
| Input leakage current at FB pin | ILKG-FB | 0.2 | 65 | nA | FB = 1.011 V | 7 | |
| Peak inductor current limit | IHS-LIMIT | 4.4 | 5.5 | 6.4 | A | 7 | |
| Inductor current valley limit | ILS-LIMIT | 2.6 | 3 | 3.3 | A | 7 | |
| Soft-start charge current | ISSC | 1.25 | 2 | 2.75 | µA | 7 | |
| Power-good flag over voltage tripping threshold | VPGOOD-HIGH | 110 | 113 | % | % of FB voltage | 7 | |
| Power-good flag under voltage tripping threshold | VPGOOD-LOW | 77 | 88 | % | % of FB voltage | 7 | |
| PGOOD pin pull down resistance when power bad | RPGOOD | 69 | 150 | Ω | VEN = 3.3 V | 7 | |
| PGOOD pin pull down resistance when power bad | RPGOOD | 150 | 350 | Ω | VEN = 0 V | 7 | |
| Minimum high side MOSFET ON time | tON-MIN | 125 | 165 | ns | 8 | ||
| Minimum high side MOSFET OFF time | tOFF-MIN | 200 | 250 | ns | 8 | ||
| Oscillator default frequency | FOSC-DEFAULT | 425 | 500 | 580 | kHz | RT pin open circuit | 8 |
| Minimum adjustable frequency | FADJ | 200 | kHz | With 1% resistors at RT pin | 8 | ||
| Maximum adjustable frequency | FADJ | 2200 | kHz | 8 | |||
| Frequency adjust accuracy | 10 | % | 8 | ||||
| Sync clock high level threshold | VSYNC-HIGH | 2 | V | 8 | |||
| Sync clock low level threshold | VSYNC-LOW | 0.4 | V | 8 | |||
| Sync clock maximum duty cycle | DSYNC-MAX | 90 | % | 8 | |||
| Sync clock minimum duty cycle | DSYNC-MIN | 10 | % | 8 | |||
| Minimum sync clock ON and OFF time | TSYNC-MIN | 80 | ns | 8 | |||
| Junction-to-ambient thermal resistance (HTSSOP) | RθJA | 38.9 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance (HTSSOP) | RθJC (Top) | 24.3 | °C/W | 6 | |||
| Junction-to-board thermal resistance (HTSSOP) | RθJB | 19.9 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance (HTSSOP) | RθJC(bot) | 1.7 | °C/W | 6 | |||
| Operating quiescent current (switching) | IQ-SW | 27 | µA | VEN = 3.3 V; IOUT = 0 A; RT = open; VBIAS = VOUT = 3.3 V; RFBT = 1 Meg | 6 | ||
| Minimum input voltage for startup | VIN-MIN-ST | 3.8 | V | 6 | |||
| Internal LDO output voltage | VCC | 3.28 | V | VIN ≥ 3.8 V | 6 | ||
| Under voltage lock out (UVLO) threshold for VCC | VCC-UVLO | 3.1 | V | VCC rising threshold | 6 | ||
| High-side MOSFET ON-resistance | RDS-ON-HS | 120 | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 7 | ||
| Low-side MOSFET ON-resistance | RDS-ON-LS | 65 | mΩ | IOUT = 1 A; VBIAS = VOUT = 3.3 V | 7 |
CAD (KiCad official)
- Symbol:
LM43603PWP - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm43603pwp-etched.step/lm43603pwp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm43603pwp.step/lm43603pwp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (59 pp, sha256
2642edca40e62388, retrieved 2026-10-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).