main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lm3743mm-300: viewers · Ray
lm3743mm-300-etched.glb Publish 0.1.0 · Ray
lm3743mm-300-etched.step lm3743mm-300: factory component page (tier=mfr) · Ray
lm3743mm-300-hero.glb lm3743mm-300: hero GLB from the etched model (keeps the MPN mark) · Ray
lm3743mm-300-hero.overlay.json Publish 0.1.0 · Ray
lm3743mm-300.glb Publish 0.1.0 · Ray
lm3743mm-300.kicad_mod Publish 0.1.0 · Ray
lm3743mm-300.kicad_sym Publish 0.1.0 · Ray
lm3743mm-300.lbr Publish 0.1.0 · Ray
lm3743mm-300.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 10 pins · Ray

LM3743MM-300

Texas Instruments · DC-DC Controllers · VSSOP-10-0.5mm

LM3743MM-300 from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VCC power_in Controller supply rail (3.0V to 5.5V) needing at least 1 µF MLCC close to VCC and GND, with a 1 to 4.99Ω series resistor from the supply rail.
2 LGATE output Gate drive for the low-side N-channel MOSFET, interlocked with HGATE to avoid shoot-through.
3 GND power_in Power ground (PGND) and signal ground (SGND); the bottom feedback resistor connects between this pin and FB.
4 ILIM passive Low-side current limit threshold setting pin that sources a fixed 50 µA, with a resistor connected to the drain of the low-side N-FET.
5 FB input Feedback pin, the inverting input of the error amplifier, used to sense the output voltage and compensate the control loop (regulates at 0.8V).
6 COMP/EN bidirectional Error amplifier output and enable pin used for loop compensation; forcing this pin to ground shuts down the IC.
7 SS/TRACK bidirectional Soft-start and tracking pin connected to the error amplifier non-inverting input during soft-start, sourcing 10.2 µA typical; a resistor divider from another supply output enables tracking.
8 SW passive Switch node pin, the lower rail of the high-side N-FET driver, also used for high-side current limit sensing.
9 HGATE output Gate drive for the high-side N-channel MOSFET, interlocked with LGATE to avoid shoot-through.
10 BOOT power_in Supply rail for the high-side N-channel MOSFET gate drive, which must be at least one gate threshold above the regulator input voltage (absolute max 12V to GND, 6V to SW).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-10-0.5mm
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
FB pin voltage in regulation VFB 0.786 0.8 0.814 V 3.0V ≤ VCC ≤ 5.5V 3
UVLO threshold rising VUVLO 2.84 3 V Input voltage rising 3
UVLO threshold falling VUVLO 2.45 2.66 V Input voltage falling 3
Operating VCC current IVCC 1.5 2.5 mA fSW = 300 kHz, LM3743-300 3
Shutdown VCC current 6 50 µA COMP/EN = 0V 3
SS/TRACK pin source current ISS/TRACK 8 10.2 12.5 µA VSS/TRACK = 0V 3
ILIM pin source current IILIM 42.5 50 57.5 µA VILIM = 0V 3
Current Limit Trip Level VILIM -25 0 25 mV 3
COMP/EN pin pull-up current ICOMP/EN 4 µA VCOMP/EN = 0V 3
High-side current limit threshold VHS-CLIM 500 mV Measured at VCC pin with respect to SW 3
FB pin Bias Current IFB 10 200 nA 3
BOOT Pin Shutdown Current ISHDN-BOOT 25 50 µA VBOOT-VSW = 3.3V, VCOMP/EN = 0V 3
Oscillator Frequency fSW 255 300 345 kHz 3.0V ≤ VCC ≤ 5.5V, LM3743-300 4
Max Duty Cycle DMAX 85 91 % fSW = 300 kHz, LM3743-300 4
COMP/EN pin logic high trip-point VCOMP/EN-HI 0.65 0.9 V 4
COMP/EN pin logic low trip-point VCOMP/EN-LO 0.1 0.45 V 4
High Side Driver Pull-up ON resistance RHG-UP 1.6 Ω VBOOT-VSW = 3.3V, IHGATE = 350mA 4
High Side Driver Pull-down ON resistance RHG-DN 1 Ω VBOOT-VSW = 3.3V, IHGATE = 350mA 4
Junction to Ambient Thermal Resistance θJA 235 °C/W 4
Supply Voltage Range VCC 3 5.5 V 3
Junction Temperature Range TJ -40 125 °C 3
VCC VCC -0.3 6 V 3
SW to GND -0.3 6 V 3
Boot to GND -0.3 12 V 3
Boot to SW -0.3 6 V 3
SS/TRACK, ILIM, COMP/EN, FB to GND -0.3 6 V -0.3V to VCC 3
Junction Temperature TJ 150 °C 3
Storage Temperature Tstg -65 150 °C 3
Lead Temperature 260 °C soldering, 10sec 3
ESD Rating -2 2 kV Human body model, 100 pF, 1.5 kΩ 3

CAD (KiCad official)

  • Symbol: LM3743MM-300
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)
  • 3D model files: lm3743mm-300-etched.step / lm3743mm-300-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm3743mm-300.step / lm3743mm-300.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (39 pp, sha256 9c8bfeb2b340733d, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF