Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM34910CSD

Texas Instruments · DC-DC Converters · WSON-10-EP(4x4)

LM34910CSD from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Internally connected to the buck switch source, connecting to the external inductor, diode, and boost capacitor.
2 BST passive Boost pin for the bootstrap capacitor, which is charged by an internal diode during the off-time; a 0.022 µF capacitor connects from SW to this pin.
3 ISEN input Current sense input connected through the current sense resistor to SGND, with current limit set at 1.25A.
4 SGND power_in Sense ground, where re-circulating current flows into the current sense resistor.
5 RTN power_in Ground for all internal circuitry other than the current limit detection.
6 FB input Feedback input to the regulation and over-voltage comparators, with a regulation level of 2.5V.
7 SS passive Soft-start pin, where an internal 11.5 µA current source charges an external capacitor to 2.5V.
8 RON/SD input An external resistor from VIN to this pin sets the buck switch on-time, and grounding this pin shuts down the regulator.
9 VCC power_out Output of the start-up regulator, nominally regulated to 7.0V, which can be fed by an external 8V-14V auxiliary voltage to reduce internal dissipation.
10 VIN power_in Input supply voltage with a nominal input range of 8.0V to 50V.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WSON-10-EP(4x4)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC regulated output VCCReg 6.6 7 7.4 V 3
IIN operating current IIN 0.63 1 mA Non-switching, FB = 3V 3
IIN shutdown current IIN 80 250 µA RON/SD = 0V 3
Buck Switch Rds(on) Rds(on) 0.45 0.95 Ω ITEST = 200 mA 3
Gate Drive UVLO UVLOGD 3 4.3 5.5 V VBST - VSW Increasing 3
ILIM threshold ILIM 1 1.25 1.5 A Current out of ISEN 4
On-time tON - 1 2.1 2.75 3.6 µs VIN = 10V, RON = 200 kΩ 4
Shutdown threshold 0.35 0.65 1.1 V Voltage at RON/SD rising 4
FB regulation threshold VREF 2.44 2.5 2.55 V SS pin = steady state 4
VIN to GND 55 V 3
BST to GND 70 V 3
SW to GND -1.5 V Steady State 3
ESD Rating 2 kV Human Body Model 3
BST to VCC 55 V 3
VIN to SW 55 V 3
BST to SW 14 V 3
VCC to GND 14 V 3
SGND to RTN -0.3 0.3 V 3
SS to RTN -0.3 4 V 3
All other inputs to GND -0.3 7 V 3
Storage temperature range -55 150 °C 3
Junction temperature (absolute maximum) 150 °C 3
VIN operating input voltage VIN 8 50 V 3
Operating junction temperature -40 125 °C 3
VIN-VCC dropout voltage 1.4 V ICC = 0 mA, VCC = VCCReg - 100 mV 3
VCC output impedance 140 Ω 0 mA ≤ ICC ≤ 5 mA 3
VCC current limit 9 mA VCC = 0V 3
VCC under-voltage lockout threshold UVLOVCC 5.8 V VCC increasing 3
VCC under-voltage lockout hysteresis UVLOVCC 150 mV VCC decreasing 3
VCC UVLO filter delay UVLOVCC 3 µs 100 mV overdrive 3
Gate Drive UVLO hysteresis UVLOGD 440 mV 3
Softstart pull-up voltage 2.5 V 4
Softstart internal current source 11.5 µA 4
Resistance from ISEN to SGND 130 mΩ 4
Current limit response time 150 ns 4
On-time tON - 2 560 ns VIN = 50V, RON = 200 kΩ 4
Threshold hysteresis 40 mV Voltage at RON/SD falling 4
Minimum off-time tOFF 280 ns 4
FB over-voltage threshold 2.875 V 4
FB bias current 100 nA 4
Thermal shutdown temperature TSD 175 °C 4
Thermal shutdown hysteresis 20 °C 4

CAD (KiCad official)

  • Symbol: LM34910CSD
  • Footprint: Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm
  • 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lm34910csd-etched.step / lm34910csd-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm34910csd.step / lm34910csd.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (21 pp, sha256 9316b05405136b7c, retrieved 2026-11-06, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF