3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLM3410YMF
Texas Instruments · LED Drivers · SOT-23-5
LM3410YMF from Texas Instruments, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Output switch pin, connected to the inductor and output diode; recommended switch voltage is 3 V to 24 V, with an absolute maximum of 26.5 V. |
| 2 | GND | power_in | Signal and power ground pin; place the bottom resistor of the feedback network as close as possible to this pin. |
| 3 | FB | input | Feedback pin; connect an external resistor from FB to GND to set the LED output current, with a 190 mV typical feedback voltage (178 mV to 202 mV) and an absolute maximum of 3 V. |
| 4 | DIM | input | Dimming and shutdown control input; logic high enables operation with 0% to 100% duty cycle, and the pin must not float or exceed VIN + 0.3 V. |
| 5 | VIN | power_in | Supply voltage pin for the power stage and input supply, with a recommended range of 2.7 V to 5.5 V and an absolute maximum of 7 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-5 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN | VIN | -0.5 | 7 | V | 4 | ||
| Input voltage SW | SW | -0.5 | 26.5 | V | 4 | ||
| Input voltage FB | FB | -0.5 | 3 | V | 4 | ||
| Input voltage DIM | DIM | -0.5 | 7 | V | 4 | ||
| Operating junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage | VIN | 2.7 | 5.5 | V | 4 | ||
| DIM control input | VDIM | 0 | 5.5 | V | 0 to VIN; do not allow to float or exceed VIN + 0.3 V | 4 | |
| Switch output | VSW | 3 | 24 | V | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Power dissipation (Internal) SOT-23 | 400 | mW | SOT-23 | 4 | |||
| Junction-to-ambient thermal resistance | RθJA | 164.2 | °C/W | DBV (SOT-23), 0 LFPM air flow | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 115.3 | °C/W | DBV (SOT-23) | 4 | ||
| Junction-to-board thermal resistance | RθJB | 27 | °C/W | DBV (SOT-23) | 4 | ||
| Junction-to-top characterization parameter | ψJT | 12.8 | °C/W | DBV (SOT-23) | 4 | ||
| Junction-to-board characterization parameter | ψJB | 26.5 | °C/W | DBV (SOT-23) | 4 | ||
| Feedback voltage | VFB | 178 | 190 | 202 | mV | VIN = 5 V, TJ = -40°C to 125°C for min/max | 5 |
| Feedback input bias current | IFB | 0.1 | 1 | µA | 5 | ||
| Switching frequency (LM3410Y) | fSW | 360 | 525 | 680 | kHz | LM3410Y | 5 |
| Maximum duty cycle (LM3410Y) | DMAX | 90 | 95 | % | LM3410Y | 5 | |
| Minimum duty cycle (LM3410Y) | DMIN | 2 | % | LM3410Y | 5 | ||
| Switch on resistance | RDS(ON) | 170 | 330 | mΩ | MSOP and SOT-23 | 5 | |
| Switch current limit | ICL | 2.1 | 2.8 | A | 5 | ||
| Quiescent current (switching), LM3410Y | IQ | 3.4 | 7 | mA | LM3410Y, VFB = 0.25 V | 5 | |
| Quiescent current (shutdown) | IQ | 80 | nA | All versions, VDIM = 0 V | 5 | ||
| Undervoltage lockout, VIN rising | UVLO | 2.3 | 2.65 | V | VIN rising | 5 | |
| Undervoltage lockout, VIN falling | UVLO | 1.7 | 1.9 | V | VIN falling | 5 | |
| Shutdown threshold voltage | VDIM_H | 0.4 | V | 5 | |||
| Enable threshold voltage | VDIM_H | 1.8 | V | 5 | |||
| Switch leakage | ISW | 1 | µA | VSW = 24 V | 5 | ||
| Dimming pin current | IDIM | 100 | nA | Sink and source | 5 | ||
| Start-up time | SU | 20 | µs | 5 | |||
| Feedback voltage line regulation | ΔVFB/VIN | 0.06 | %/V | VIN = 2.7 V to 5.5 V | 5 | ||
| Thermal shutdown temperature | TSD | 165 | °C | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | For 5-pin SOT-23 package typical applications, RθJA numbers range from 164.2°C/W, and RθJC varies from 115.3°C/W. These values are for PCBs with two and four layer boards with 0.5 oz copper, with two | 40 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
LM3410YMF - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lm3410ymf-etched.step/lm3410ymf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm3410ymf.step/lm3410ymf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (57 pp, sha256
0311b7eeee2c8ced, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).