main
Ray
Publish 0.1.0
c84d510
LM3406HVMHX
Texas Instruments · LED Drivers · TSSOP-14
LM3406HVMHX from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch pin that connects to the output inductor and Schottky diode; the datasheet gives no voltage limit for this pin alone, with SW to GND rated -1.5V to 45V for LM3406 and -1.5V to 76V for LM3406HV. |
| 2 | SW | output | Switch pin that connects to the output inductor and Schottky diode; it is tied to pin 1 on the package. |
| 3 | BOOT | passive | MOSFET drive bootstrap pin that requires a 22 nF ceramic capacitor connected from this pin to the SW pins. |
| 4 | NC | unconnected | No internal connection; leave this pin unconnected. |
| 5 | VOUT | input | Output voltage sense pin that connects to the output node where the inductor and the first LED anode connect. |
| 6 | CS | input | Current sense feedback pin; the LED current is set by a resistor from this pin to ground. |
| 7 | GND | power_in | Ground pin that connects to system ground. |
| 8 | DIM | input | Input for PWM dimming; logic high turns the output on and logic low turns it off, with DIM to GND rated -0.3V to 7V. |
| 9 | COMP | passive | Error amplifier output that connects to ground through a 0.1 µF ceramic capacitor with X5R or X7R dielectric. |
| 10 | RON | input | On-time control pin; a resistor from this pin to VIN sets the regulator controlled on-time, with RON to GND rated -0.3V to 7V. |
| 11 | VCC | power_out | Output of the internal 7V linear regulator that must be bypassed to ground with a minimum 0.1 µF ceramic capacitor with X5R or X7R dielectric. |
| 12 | VINS | input | Input voltage PWM dimming comparator input that connects to the anode of the input diode to allow dimming by PWM of the input voltage. |
| 13 | VIN | power_in | Input voltage pin with a nominal operating input range of 6V to 75V for the LM3406HV variant. |
| 14 | VIN | power_in | Input voltage pin with a nominal operating input range of 6V to 75V for the LM3406HV variant; it is tied to pin 13 on the package. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-14 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | -0.3 | 76 | V | 3 | |||
| VINS to GND | -0.3 | 76 | V | 3 | |||
| VOUT to GND | -0.3 | 76 | V | 3 | |||
| BOOT to GND | -0.3 | 76 | V | 3 | |||
| SW to GND | -1.5 | 76 | V | 3 | |||
| BOOT to VCC | -0.3 | 76 | V | 3 | |||
| BOOT to SW | -0.3 | 14 | V | 3 | |||
| VCC to GND | -0.3 | 14 | V | 3 | |||
| DIM to GND | -0.3 | 7 | V | 3 | |||
| COMP to GND | -0.3 | 7 | V | 3 | |||
| CS to GND | -0.3 | 7 | V | 3 | |||
| RON to GND | -0.3 | 7 | V | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| Storage Temp. Range | -65 | 125 | °C | 3 | |||
| ESD Rating | 2 | kV | Human body model | 3 | |||
| Lead Temperature (Soldering, 10sec) | 260 | °C | 3 | ||||
| Infrared/Convection Reflow (15sec) | 235 | °C | 3 | ||||
| VIN Input voltage range (LM3406HV) | VIN | 6 | 75 | V | LM3406HV, LM3406HV-Q1 | 3 | |
| Junction Temperature Range (LM3406, LM3406HV) | -40 | 125 | °C | LM3406, LM3406HV | 3 | ||
| VREF CS Regulation Threshold | VREF | 187.5 | 200 | 210 | mV | CS Decreasing, SW turns on | 4 |
| VREF CS Regulation Threshold (over operating temperature) | VREF | 191 | 210 | mV | CS Decreasing, SW turns on | 4 | |
| Shutdown Threshold | VSD-TH | 0.3 | 0.7 | 1.05 | V | RON Increasing | 4 |
| Programmed On-time | tON | 800 | 1300 | 1800 | ns | VIN = 24V, VO = 12V, RON = 200kΩ | 4 |
| VINS Pin Threshold | VINS-TH | 70 | %VIN | VINS decreasing | 4 | ||
| VCC Regulated Output | VCC-REG | 6.4 | 7 | 7.4 | V | 0 mA < ICC < 5 mA | 4 |
| VCC Current Limit | VCC-LIM | 4 | 20 | mA | VIN = 24V, VCC = 0V | 4 | |
| Current Limit Threshold | ILIM | 1.7 | 2.1 | 2.7 | A | 4 | |
| BOOT Under-voltage Lock-out Threshold | VDR-UVLO | 1.7 | 2.9 | 4.3 | V | BOOT-SW Increasing | 4 |
| Buck Switch On Resistance | RDS-ON | 0.37 | 0.75 | Ω | ISW = 200 mA, BOOT = 6.3V | 4 | |
| Junction to Ambient TSSOP-14 Package | θJA | 50 | °C/W | DAP soldered to minimum 2 square inches of 1-oz copper | 5 | ||
| Minimum Off-time | tOFF-MIN | 230 | ns | CS = 0V | 4 | ||
| Minimum On-time | tON-MIN | 280 | ns | 4 | |||
| CS Over-voltage Threshold | V0V | 300 | mV | CS Increasing, SW turns off | 4 | ||
| CS Bias Current | ICS | 0.9 | µA | CS = 0V | 4 | ||
| VOUT Bias Current | IVOUT | 83 | µA | VOUT = 24V | 4 | ||
| COMP Pin Current | ICOMP | 25 | µA | CS = 0V | 4 | ||
| Error Amplifier Transconductance | Gm-CS | 145 | µS | 150 mV < CS < 250 mV | 4 | ||
| Shutdown Hysteresis | VSD-HYS | 40 | mV | RON Decreasing | 4 | ||
| VINS Pin Input Current | IIN-2WD | 25 | µA | VINS = 24V * 0.7 | 4 | ||
| VCC Bypass Threshold | VCC-BP-TH | 8.8 | V | VIN Increasing | 4 | ||
| VCC Under-voltage Lock-out Threshold | VCC-UV-TH | 5.3 | V | VCC Increasing | 4 | ||
| VCC Under-voltage Lock-out Hysteresis | VCC-UV-HYS | 150 | mV | VCC Decreasing | 4 | ||
| IIN Operating Current | IIN-OP | 1.2 | mA | Non-switching, CS = 0.5V | 4 | ||
| IIN Shutdown Current | IIN-SD | 240 | 350 | µA | RON = 0V | 4 | |
| Logic High (DIM) | VIH | 2.2 | V | DIM Increasing | 4 | ||
| Logic Low (DIM) | VIL | 0.8 | V | DIM Decreasing | 4 | ||
| DIM Pull-up Current | IDIM-PU | 80 | µA | DIM = 1.5V | 4 | ||
| BOOT Under-voltage Lock-out Hysteresis | VDR-HYS | 370 | mV | BOOT-SW Decreasing | 4 | ||
| Thermal Shutdown Threshold | TSD | 165 | °C | 4 | |||
| Thermal Shutdown Hysteresis | TSD-HYS | 25 | °C | 4 |
CAD (KiCad official)
- Symbol:
LM3406HVMHX - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
lm3406hvmhx-etched.step/lm3406hvmhx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm3406hvmhx.step/lm3406hvmhx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
701e308df9f549cb, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM3406HVMHX
**Texas Instruments** · LED Drivers · TSSOP-14
LM3406HVMHX from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | Switch pin that connects to the output inductor and Schottky diode; the datasheet gives no voltage limit for this pin alone, with SW to GND rated -1.5V to 45V for LM3406 and -1.5V to 76V for LM3406HV. |
| 2 | SW | output | Switch pin that connects to the output inductor and Schottky diode; it is tied to pin 1 on the package. |
| 3 | BOOT | passive | MOSFET drive bootstrap pin that requires a 22 nF ceramic capacitor connected from this pin to the SW pins. |
| 4 | NC | unconnected | No internal connection; leave this pin unconnected. |
| 5 | VOUT | input | Output voltage sense pin that connects to the output node where the inductor and the first LED anode connect. |
| 6 | CS | input | Current sense feedback pin; the LED current is set by a resistor from this pin to ground. |
| 7 | GND | power_in | Ground pin that connects to system ground. |
| 8 | DIM | input | Input for PWM dimming; logic high turns the output on and logic low turns it off, with DIM to GND rated -0.3V to 7V. |
| 9 | COMP | passive | Error amplifier output that connects to ground through a 0.1 µF ceramic capacitor with X5R or X7R dielectric. |
| 10 | RON | input | On-time control pin; a resistor from this pin to VIN sets the regulator controlled on-time, with RON to GND rated -0.3V to 7V. |
| 11 | VCC | power_out | Output of the internal 7V linear regulator that must be bypassed to ground with a minimum 0.1 µF ceramic capacitor with X5R or X7R dielectric. |
| 12 | VINS | input | Input voltage PWM dimming comparator input that connects to the anode of the input diode to allow dimming by PWM of the input voltage. |
| 13 | VIN | power_in | Input voltage pin with a nominal operating input range of 6V to 75V for the LM3406HV variant. |
| 14 | VIN | power_in | Input voltage pin with a nominal operating input range of 6V to 75V for the LM3406HV variant; it is tied to pin 13 on the package. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-14 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN to GND | | -0.3 | | 76 | V | | 3 |
| VINS to GND | | -0.3 | | 76 | V | | 3 |
| VOUT to GND | | -0.3 | | 76 | V | | 3 |
| BOOT to GND | | -0.3 | | 76 | V | | 3 |
| SW to GND | | -1.5 | | 76 | V | | 3 |
| BOOT to VCC | | -0.3 | | 76 | V | | 3 |
| BOOT to SW | | -0.3 | | 14 | V | | 3 |
| VCC to GND | | -0.3 | | 14 | V | | 3 |
| DIM to GND | | -0.3 | | 7 | V | | 3 |
| COMP to GND | | -0.3 | | 7 | V | | 3 |
| CS to GND | | -0.3 | | 7 | V | | 3 |
| RON to GND | | -0.3 | | 7 | V | | 3 |
| Junction Temperature | | | | 150 | °C | | 3 |
| Storage Temp. Range | | -65 | | 125 | °C | | 3 |
| ESD Rating | | | | 2 | kV | Human body model | 3 |
| Lead Temperature (Soldering, 10sec) | | | | 260 | °C | | 3 |
| Infrared/Convection Reflow (15sec) | | | | 235 | °C | | 3 |
| VIN Input voltage range (LM3406HV) | VIN | 6 | | 75 | V | LM3406HV, LM3406HV-Q1 | 3 |
| Junction Temperature Range (LM3406, LM3406HV) | | -40 | | 125 | °C | LM3406, LM3406HV | 3 |
| VREF CS Regulation Threshold | VREF | 187.5 | 200 | 210 | mV | CS Decreasing, SW turns on | 4 |
| VREF CS Regulation Threshold (over operating temperature) | VREF | 191 | | 210 | mV | CS Decreasing, SW turns on | 4 |
| Shutdown Threshold | VSD-TH | 0.3 | 0.7 | 1.05 | V | RON Increasing | 4 |
| Programmed On-time | tON | 800 | 1300 | 1800 | ns | VIN = 24V, VO = 12V, RON = 200kΩ | 4 |
| VINS Pin Threshold | VINS-TH | | 70 | | %VIN | VINS decreasing | 4 |
| VCC Regulated Output | VCC-REG | 6.4 | 7 | 7.4 | V | 0 mA < ICC < 5 mA | 4 |
| VCC Current Limit | VCC-LIM | 4 | | 20 | mA | VIN = 24V, VCC = 0V | 4 |
| Current Limit Threshold | ILIM | 1.7 | 2.1 | 2.7 | A | | 4 |
| BOOT Under-voltage Lock-out Threshold | VDR-UVLO | 1.7 | 2.9 | 4.3 | V | BOOT-SW Increasing | 4 |
| Buck Switch On Resistance | RDS-ON | | 0.37 | 0.75 | Ω | ISW = 200 mA, BOOT = 6.3V | 4 |
| Junction to Ambient TSSOP-14 Package | θJA | | 50 | | °C/W | DAP soldered to minimum 2 square inches of 1-oz copper | 5 |
| Minimum Off-time | tOFF-MIN | | 230 | | ns | CS = 0V | 4 |
| Minimum On-time | tON-MIN | | 280 | | ns | | 4 |
| CS Over-voltage Threshold | V0V | | 300 | | mV | CS Increasing, SW turns off | 4 |
| CS Bias Current | ICS | | 0.9 | | µA | CS = 0V | 4 |
| VOUT Bias Current | IVOUT | | 83 | | µA | VOUT = 24V | 4 |
| COMP Pin Current | ICOMP | | 25 | | µA | CS = 0V | 4 |
| Error Amplifier Transconductance | Gm-CS | | 145 | | µS | 150 mV < CS < 250 mV | 4 |
| Shutdown Hysteresis | VSD-HYS | | 40 | | mV | RON Decreasing | 4 |
| VINS Pin Input Current | IIN-2WD | | 25 | | µA | VINS = 24V * 0.7 | 4 |
| VCC Bypass Threshold | VCC-BP-TH | | 8.8 | | V | VIN Increasing | 4 |
| VCC Under-voltage Lock-out Threshold | VCC-UV-TH | | 5.3 | | V | VCC Increasing | 4 |
| VCC Under-voltage Lock-out Hysteresis | VCC-UV-HYS | | 150 | | mV | VCC Decreasing | 4 |
| IIN Operating Current | IIN-OP | | 1.2 | | mA | Non-switching, CS = 0.5V | 4 |
| IIN Shutdown Current | IIN-SD | | 240 | 350 | µA | RON = 0V | 4 |
| Logic High (DIM) | VIH | | 2.2 | | V | DIM Increasing | 4 |
| Logic Low (DIM) | VIL | | 0.8 | | V | DIM Decreasing | 4 |
| DIM Pull-up Current | IDIM-PU | | 80 | | µA | DIM = 1.5V | 4 |
| BOOT Under-voltage Lock-out Hysteresis | VDR-HYS | | 370 | | mV | BOOT-SW Decreasing | 4 |
| Thermal Shutdown Threshold | TSD | | 165 | | °C | | 4 |
| Thermal Shutdown Hysteresis | TSD-HYS | | 25 | | °C | | 4 |
## CAD (KiCad official)
- Symbol: `LM3406HVMHX`
- Footprint: `Package_SO:TSSOP-14_4.4x5mm_P0.65mm`
- 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files: `lm3406hvmhx-etched.step` / `lm3406hvmhx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm3406hvmhx.step` / `lm3406hvmhx.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm3406.pdf) (42 pp, sha256 `701e308df9f549cb`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm3406hvmhx-datasheet.pdf)