3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM3405AXMYX
Texas Instruments · LED Drivers · MSOP-8-EP
LM3405AXMYX from Texas Instruments, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Feedback pin. Connect FB to the LED string cathode and an external resistor to ground to set the LED current. |
| 2 | GND | power_in | Signal and power ground pin. Place the bottom resistor of the feedback network as close as possible to this pin. |
| 3 | NC | unconnected | No connection. |
| 4 | BOOST | output | Boost voltage that drives the NMOS output switch. A bootstrap capacitor is connected between the BOOST and SW pins. |
| 5 | SW | output | Switch pin. Connect this pin to the inductor, catch diode, and bootstrap capacitor. |
| 6 | VIN | power_in | Input supply voltage. Connect a bypass capacitor locally from this pin to GND. |
| 7 | GND | power_in | Signal and power ground pin. Place the bottom resistor of the feedback network as close as possible to this pin. |
| 8 | EN/DIM | input | Enable control input. Logic high enables operation. Do not allow this pin to float or be greater than VIN + 0.3 V. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | MSOP-8-EP |
| Category | LED Drivers |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN input voltage | VIN | -0.5 | 24 | V | 4 | ||
| SW voltage | -0.5 | 24 | V | 4 | |||
| Boost voltage | -0.5 | 30 | V | 4 | |||
| Boost to SW voltage | -0.5 | 6 | V | 4 | |||
| FB voltage | -0.5 | 3 | V | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Feedback voltage | VFB | 0.188 | 0.205 | 0.22 | V | 5 | |
| Feedback input bias current | IFB | 10 | 250 | nA | Sink/source | 5 | |
| Undervoltage lockout rising | UVLO | 2.74 | 2.95 | V | VIN Rising | 5 | |
| Undervoltage lockout falling | UVLO | 1.9 | 2.3 | V | VIN Falling | 5 | |
| Switching frequency | fSW | 1.2 | 1.6 | 1.9 | MHz | 5 | |
| Maximum duty cycle | DMAX | 85 | 94 | % | VFB = 0 V | 5 | |
| Switch ON resistance MSOP-PowerPAD | RDS(ON) | 360 | 700 | mΩ | VBOOST - VSW = 3 V | 5 | |
| Switch current limit | ICL | 1.2 | 2 | 2.8 | A | VBOOST - VSW = 3 V, VIN = 3 V | 5 |
| Quiescent current (switching) | IQ | 1.8 | 2.8 | mA | Switching, VFB = 0.195 V | 5 | |
| VIN operating range | VIN | 3 | 22 | V | 4 | ||
| Boost to SW voltage operating range | 2.5 | 5.5 | V | 4 | |||
| Junction temperature operating range | TJ | -40 | 125 | °C | 4 | ||
| LED current | ILED | 1 | A | MSOP-PowerPAD package | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 55.3 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 62.8 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 38.9 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 8.2 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 38.6 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 8 | °C/W | DGN (MSOP-PowerPAD) 8 pins | 5 |
CAD (KiCad official)
- Symbol:
LM3405AXMYX - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lm3405axmyx-etched.step/lm3405axmyx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm3405axmyx.step/lm3405axmyx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
6ffca81b353b1a67, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).