LM2903L-Q1
Public Made by Adomby adom
Texas Instruments , X2QFN-10 (RUG). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗PCB Footprint
Open full view ↗Datasheet
Open in new tab ↗README
markdownLM2903L-Q1
Texas Instruments · IC · X2QFN-10 (RUG)
LM2903L-Q1 from Texas Instruments, in a X2QFN-10 (RUG). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V- | power_in | Negative supply voltage; the supply range is 2.7V to 36V across (V+) minus (V-). |
| 2 | CLR A | input | Clear input for comparator A that clears the latch on a falling edge, with inputs rated from -0.1V to 36V relative to (V-). |
| 3 | CLR B | input | Clear input for comparator B that clears the latch on a falling edge, with inputs rated from -0.1V to 36V relative to (V-). |
| 4 | IN+ B | input | Non-inverting input of comparator B, with common-mode range from (V-) to (V+) minus 2V. |
| 5 | IN- B | input | Inverting input of comparator B, with common-mode range from (V-) to (V+) minus 2V. |
| 6 | V+ | power_in | Positive supply voltage; the supply range is 2.7V to 36V across (V+) minus (V-). |
| 7 | OUT B | output | Output of comparator B, an open-drain output with an output voltage range of 0 to 36V from (V-). |
| 8 | OUT A | output | Output of comparator A, an open-drain output with an output voltage range of 0 to 36V from (V-). |
| 9 | IN- A | input | Inverting input of comparator A, with common-mode range from (V-) to (V+) minus 2V. |
| 10 | IN+ A | input | Non-inverting input of comparator A, with common-mode range from (V-) to (V+) minus 2V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | X2QFN-10 (RUG) |
| Category | |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VS | 2.7 | 36 | V | VS = (V+) - (V-) | 5 | |
| Input voltage range (IN+, IN-, CLR) | -0.1 | 36 | V | from (V-) | 5 | ||
| Output voltage range | 0 | 36 | V | from (V-) | 5 | ||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Supply voltage | VS | -0.3 | 38 | V | VS = (V+), (V-) | 5 | |
| Input pins (IN+, IN-, CLR) | -0.3 | 38 | V | from (V-) | 5 | ||
| Output (OUT) | -0.3 | 38 | V | from (V-) | 5 | ||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input threshold voltage | VT | -2.5 | 0.3 | 2.5 | mV | VS = 5 to 36V | 7 |
| Input threshold voltage | VT | -3 | 3 | mV | VS = 5 to 36V, TA = -40°C to +125°C | 7 | |
| Quiescent current per comparator | IQ | 250 | 400 | µA | VS = 5V, No Load, Output Low | 7 | |
| Quiescent current per comparator | IQ | 600 | µA | VS = 36V, No Load, Output Low, TA = -40°C to +125°C | 7 | ||
| Input bias current | IB | -3.5 | -25 | nA | 7 | ||
| Input bias current | IB | -50 | nA | TA = -40°C to +125°C | 7 | ||
| Input offset current | IOS | -10 | 0.5 | 10 | nA | 7 | |
| Input offset current | IOS | -25 | 25 | nA | TA = -40°C to +125°C | 7 | |
| Voltage input high threshold of CLR | VIH_CLR | 1.1 | V | 7 | |||
| Voltage input low threshold of CLR | VIL_CLR | 0.6 | V | 7 | |||
| Large signal differential voltage amplification | AVD | 50 | 200 | V/mV | VS = 15V, VO = 1.4V to 11.4V; RL ≥ 15k to (V+) | 7 | |
| Voltage swing from (V-) | VOL | 110 | 400 | mV | ISINK ≤ 4mA, VID = -1V | 7 | |
| Voltage swing from (V-) | VOL | 550 | mV | ISINK ≤ 4mA, VID = -1V, TA = -40°C to +125°C | 7 | ||
| Open-drain output leakage current | ILKG | 0.1 | 20 | nA | (V+) = VO = 5V; VID = 1V | 7 | |
| Open-drain output leakage current | ILKG | 0.3 | 50 | nA | (V+) = VO = 36V; VID = 1V | 7 | |
| Low Level Output Current | IOL | 6 | 21 | mA | VOL = 1.5V; VID = -1V; VS = 5V | 7 | |
| Propagation delay time, high-to-low (TTL input) | TPD-HL | 300 | ns | Delay from mid-point of input to mid-point of output, RP = 5.1kΩ | 8 | ||
| Propagation delay time, high-to-low (input overdrive 5mV) | TPD-HL | 1000 | ns | Input overdrive = 5mV, Input step = 100mV from mid-point of input to mid-point of output, RP = 5.1kΩ | 8 | ||
| Clear Fall to Latch Reset propagation delay time | TPD-CLR-F | 650 | ns | CLR = 1.8V to 5V, VID = 100mV, RP = 5.1kΩ | 8 | ||
| Minimum Clear Hold Pulse time | CLR_Min_Pulse_Width | 70 | ns | CLR = 1.8V to 5V, VID= +100 mV | 8 | ||
| 5V Output Fall Time, 80% to 20% | TFALL | 20 | ns | VID = -100mV | 8 | ||
| Junction-to-ambient thermal resistance | RqJA | 150 | °C/W | RUG (X2QFN) package | 6 | ||
| Junction-to-case (top) thermal resistance | RqJC(top) | 58 | °C/W | RUG (X2QFN) package | 6 | ||
| Junction-to-board thermal resistance | RqJB | 78 | °C/W | RUG (X2QFN) package | 6 | ||
| Junction-to-top characterization parameter | yJT | 1.3 | °C/W | RUG (X2QFN) package | 6 | ||
| Junction-to-board characterization parameter | yJB | 78 | °C/W | RUG (X2QFN) package | 6 |
CAD (Adom-generated)
- Symbol:
LM2903L-Q1 - Footprint:
Adom_Gen:Texas_Instruments_LM2903 - 3D model: generated to fit the land (STEP)
- 3D model files:
lm2903l-q1-etched.step/lm2903l-q1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm2903l-q1.step/lm2903l-q1.glbare the bare package body.
Provenance
TI lists LM2903L-Q1 as Preview (not orderable at distributors yet): TI product page. This page was built from the manufacturer datasheet.
Land pattern: LM2903L-Q1's datasheet (SLVSL49, Advance Information) shows the RUG package only as TI's generic view. The footprint follows TI's own RUG0010A drawing for the same X2QFN-10 package, from the TLV9002 datasheet (package outline 4231745/B). TI also publishes a RUG0010B revision whose pads differ by about 0.05 mm; TI's pages do not say which one LM2903L-Q1 uses. Check against the final datasheet when TI releases it.
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (25 pp, sha256
c13f5e25c882aa85, retrieved 2026-11-04, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.