main
Ray
Publish 0.1.0
3322de6
LM2575S-12-MS
MSKSEMI · Linear Voltage Regulators (LDO) · TO-263-5
LM2575S-12-MS from MSKSEMI, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Vin | power_in | Positive input supply for the switching regulator, which needs a suitable input bypass capacitor located close to the pin to limit voltage transients and supply switching currents. |
| 2 | Output | output | Internal switch output that swings between (+VIN − VSAT) and approximately −0.5V at a duty cycle of about VOUT/VIN, so the PCB copper area on this pin should be kept to a minimum. |
| 3 | Gnd | power_in | Circuit ground for the regulator. |
| 4 | Feedback | input | Senses the regulated output voltage to close the feedback loop. |
| 5 | ON/OFF | input | Logic-level shutdown input: pulling below approximately 1.3V turns the regulator on and pulling above 1.3V, up to a maximum of 25V, shuts it down, while leaving it open or wiring it to ground keeps it on. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MSKSEMI |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | 11.4 | 12 | 12.6 | V | 15V ≤ VIN ≤ 40V, 0.2A ≤ ILOAD ≤ 2A | 4 |
| Oscillator Frequency | fO | 110 | 150 | 173 | kHz | 5 | |
| Saturation Voltage | VSAT | 1.16 | 1.5 | V | IOUT = 2A (Notes 7, 8) | 5 | |
| Current Limit Peak Current | ICL | 3.4 | 4.5 | 7.5 | A | Peak Current (Notes 7, 8) | 5 |
| Output Leakage Current | IL | 50 | µA | Output = 0V (Notes 7, 9) | 5 | ||
| Output Leakage Current | IL | 2 | 30 | mA | Output = −1V (Note 10) | 5 | |
| Quiescent Current | IQ | 5 | 10 | mA | (Note 9) | 5 | |
| Standby Quiescent Current | ISTBY | 80 | 250 | µA | ON/OFF pin = 5V (OFF) (Note 10) | 5 | |
| ON/OFF Pin Logic Input Threshold Voltage | VIH | 0.6 | V | Low (Regulator ON) | 5 | ||
| ON/OFF Pin Logic Input Threshold Voltage | VIL | 2 | V | High (Regulator OFF) | 5 | ||
| ON/OFF Pin Input Current | IH | 5 | 15 | µA | VLOGIC = 2.5V (Regulator OFF) | 6 | |
| ON/OFF Pin Input Current | IL | 0.02 | 5 | µA | VLOGIC = 0.5V (Regulator ON) | 6 | |
| Thermal Resistance Junction to Case | JC | 2 | ˚C/W | TO-220 or TO-263 Package, Junction to Case | 5 | ||
| Thermal Resistance Junction to Ambient | JA | 50 | ˚C/W | TO-263 Package, Junction to Ambient (Note 12) | 5 | ||
| Thermal Resistance Junction to Ambient | JA | 30 | ˚C/W | TO-263 Package, Junction to Ambient (Note 13) | 5 | ||
| Thermal Resistance Junction to Ambient | JA | 20 | ˚C/W | TO-263 Package, Junction to Ambient (Note 14) | 5 | ||
| ON/OFF Pin Input Voltage | -0.3 | 25 | V | ON/OFF pin | 3 | ||
| Feedback Pin Voltage | -0.3 | 25 | V | Feedback pin | 3 | ||
| Output Voltage to Ground | -1 | V | Steady State | 3 | |||
| Maximum Supply Voltage | 45 | V | LM2575 | 3 | |||
| Storage Temperature Range | -65 | 150 | ˚C | 3 | |||
| ESD Susceptibility | 2 | kV | Human Body Model | 3 | |||
| Maximum Junction Temperature | TJ | 150 | ˚C | 3 | |||
| Lead Temperature Vapor Phase | 215 | ˚C | S Package, Vapor Phase (60 sec.) | 3 | |||
| Lead Temperature Infrared | 245 | ˚C | S Package, Infrared (10 sec.) | 3 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | ˚C | 3 | ||
| Supply Voltage | 40 | V | LM2575 | 3 |
CAD (KiCad official)
- Symbol:
LM2575S-12-MS - Footprint:
Package_TO_SOT_SMD:TO-263-5_TabPin6 - 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files:
lm2575s-12-ms-etched.step/lm2575s-12-ms-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm2575s-12-ms.step/lm2575s-12-ms.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MSKSEMI datasheet (19 pp, sha256
ba1ba56f85adba0d, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed (audit)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM2575S-12-MS
**MSKSEMI** · Linear Voltage Regulators (LDO) · TO-263-5
LM2575S-12-MS from MSKSEMI, in a TO-263-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Vin | power_in | Positive input supply for the switching regulator, which needs a suitable input bypass capacitor located close to the pin to limit voltage transients and supply switching currents. |
| 2 | Output | output | Internal switch output that swings between (+VIN − VSAT) and approximately −0.5V at a duty cycle of about VOUT/VIN, so the PCB copper area on this pin should be kept to a minimum. |
| 3 | Gnd | power_in | Circuit ground for the regulator. |
| 4 | Feedback | input | Senses the regulated output voltage to close the feedback loop. |
| 5 | ON/OFF | input | Logic-level shutdown input: pulling below approximately 1.3V turns the regulator on and pulling above 1.3V, up to a maximum of 25V, shuts it down, while leaving it open or wiring it to ground keeps it on. |
| 6 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MSKSEMI |
| Package | TO-263-5 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage | VOUT | 11.4 | 12 | 12.6 | V | 15V ≤ VIN ≤ 40V, 0.2A ≤ ILOAD ≤ 2A | 4 |
| Oscillator Frequency | fO | 110 | 150 | 173 | kHz | | 5 |
| Saturation Voltage | VSAT | | 1.16 | 1.5 | V | IOUT = 2A (Notes 7, 8) | 5 |
| Current Limit Peak Current | ICL | 3.4 | 4.5 | 7.5 | A | Peak Current (Notes 7, 8) | 5 |
| Output Leakage Current | IL | | | 50 | µA | Output = 0V (Notes 7, 9) | 5 |
| Output Leakage Current | IL | | 2 | 30 | mA | Output = −1V (Note 10) | 5 |
| Quiescent Current | IQ | | 5 | 10 | mA | (Note 9) | 5 |
| Standby Quiescent Current | ISTBY | | 80 | 250 | µA | ON/OFF pin = 5V (OFF) (Note 10) | 5 |
| ON/OFF Pin Logic Input Threshold Voltage | VIH | | | 0.6 | V | Low (Regulator ON) | 5 |
| ON/OFF Pin Logic Input Threshold Voltage | VIL | 2 | | | V | High (Regulator OFF) | 5 |
| ON/OFF Pin Input Current | IH | | 5 | 15 | µA | VLOGIC = 2.5V (Regulator OFF) | 6 |
| ON/OFF Pin Input Current | IL | | 0.02 | 5 | µA | VLOGIC = 0.5V (Regulator ON) | 6 |
| Thermal Resistance Junction to Case | JC | | 2 | | ˚C/W | TO-220 or TO-263 Package, Junction to Case | 5 |
| Thermal Resistance Junction to Ambient | JA | | 50 | | ˚C/W | TO-263 Package, Junction to Ambient (Note 12) | 5 |
| Thermal Resistance Junction to Ambient | JA | | 30 | | ˚C/W | TO-263 Package, Junction to Ambient (Note 13) | 5 |
| Thermal Resistance Junction to Ambient | JA | | 20 | | ˚C/W | TO-263 Package, Junction to Ambient (Note 14) | 5 |
| ON/OFF Pin Input Voltage | | -0.3 | | 25 | V | ON/OFF pin | 3 |
| Feedback Pin Voltage | | -0.3 | | 25 | V | Feedback pin | 3 |
| Output Voltage to Ground | | -1 | | | V | Steady State | 3 |
| Maximum Supply Voltage | | | | 45 | V | LM2575 | 3 |
| Storage Temperature Range | | -65 | | 150 | ˚C | | 3 |
| ESD Susceptibility | | | | 2 | kV | Human Body Model | 3 |
| Maximum Junction Temperature | TJ | | | 150 | ˚C | | 3 |
| Lead Temperature Vapor Phase | | | | 215 | ˚C | S Package, Vapor Phase (60 sec.) | 3 |
| Lead Temperature Infrared | | | | 245 | ˚C | S Package, Infrared (10 sec.) | 3 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | ˚C | | 3 |
| Supply Voltage | | | | 40 | V | LM2575 | 3 |
## CAD (KiCad official)
- Symbol: `LM2575S-12-MS`
- Footprint: `Package_TO_SOT_SMD:TO-263-5_TabPin6`
- 3D model: TO-263-5 (KiCad packages3D, STEP)
- 3D model files: `lm2575s-12-ms-etched.step` / `lm2575s-12-ms-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm2575s-12-ms.step` / `lm2575s-12-ms.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MSKSEMI datasheet](docs/lm2575s-12-ms-datasheet.pdf) (19 pp, sha256 `ba1ba56f85adba0d`, retrieved 2026-10-27, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed (audit)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm2575s-12-ms-datasheet.pdf)