main
History Download
Ray Publish 0.1.0 fe1d89c

LM25088MHX-2

Texas Instruments · DC-DC Controllers · HTSSOP-16-EP

LM25088MHX-2 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in IC supply voltage with an operating range of 4.5 V to 42 V.
2 EN input Below 0.4 V puts the regulator in low power state, 0.4 V to 1.2 V selects standby, and above 1.2 V enables the controller; a 5-µA pullup forces it high when left open.
3 SS passive Soft-start pin charged by an internal 11-µA source to set start-up rate, held low in standby, VCC UV and thermal shutdown, and usable for tracking below the 1.2-V reference.
4 RAMP passive An external capacitor between RAMP and GND sets the emulated current ramp slope, with a recommended range of 100 pF to 2000 pF.
5 RT/SYNC input A single resistor to GND sets the oscillator from 50 kHz to 1 MHz, and an external sync signal higher in frequency than the programmed rate can be applied through a small coupling capacitor.
6 GND power_in Ground return for the controller.
7 COMP output Output of the internal error amplifier, to which the loop compensation network must be connected between COMP and FB.
8 FB input Inverting input of the internal error amplifier with a regulation threshold of 1.205 V.
9 OUT input Output voltage connection that must be connected directly to the regulated output voltage.
10 RES passive Hiccup mode restart capacitor pin (LM25088-2 only) that times hiccup current limiting, with the HG drive disabled when RES reaches 1.2 V and normal operation resuming below 0.2 V.
11 CSG passive Current sense ground serving as the low-side reference for the current sense resistor.
12 CS input Current measurement connection for the re-circulating diode, sensed through an external resistor and an internal sample-and-hold at the end of the buck off time.
13 SW passive Switching node that connects to the source terminal of the external MOSFET switch.
14 HG output High-side gate drive output that connects to the gate terminal of the external MOSFET switch.
15 BOOT power_in Bootstrap capacitor input that requires an external capacitor between BOOT and SW, charged from VCC through an internal diode during the buck off time.
16 VCC power_out Bias regulator output that tracks VIN up to 7.8 V typical and requires a 0.1-µF to 10-µF decoupling capacitor, with an external supply of 8.3 V to 13 V accepted to reduce dissipation.
17 EP passive Exposed pad that is electrically isolated and must be soldered to the ground plane to reduce thermal resistance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, VOUT to GND VIN, VOUT 45 V 5
BOOT to GND BOOT 60 V 5
SW to GND SW -2 45 V 5
VCC to GND VCC -0.3 16 V 5
HG to SW HG -0.3 V 5
EN to GND EN 14 V 5
BOOT to SW BOOT-SW -0.3 16 V 5
CS, CSG to GND CS, CSG -0.3 0.3 V 5
All other inputs to GND -0.3 7 V 5
Junction temperature TJ 150 °C 5
Storage temperature Tstg -65 150 °C 5
VIN voltage VIN 4.5 42 V 5
VCC voltage (externally supplied) VCC 8.3 13 V 5
Operation junction temperature TJ -40 125 °C 5
Junction-to-ambient thermal resistance RθJA 40 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 6 °C/W 5
VIN operating current IBIAS 4.5 mA VFB = 1.3 V 6
VIN standby current ISTANDBY 3 mA VEN = 1 V 6
VIN shutdown current ISHUTDOWN 24 µA VEN = 0 V 6
VCC regulation VVCC(Reg) 7.4 7.8 8.2 V VVCC = open 6
VCC sourcing current limit 25 30 mA VVCC = 0 6
VCC undervoltage lockout threshold VVCC(UV) 3.7 4 4.2 V Positive going VVCC 6
VCC undervoltage hysteresis 200 mV 6
EN shutdown threshold 320 400 480 mV VEN rising 6
EN shutdown hysteresis 100 mV VEN falling 6
EN standby threshold 1.1 1.2 1.3 V VEN rising 6
EN standby hysteresis 120 mV VEN falling 6
EN pullup current source 5 µA VEN = 0 V 6
SS pullup current 8 11 13 µA Source VSS = 0 V 6
FB to SS offset 150 mV VFB = 1.3 V 6
FB reference voltage VREF 1.187 1.205 1.223 V Measured at FB pin, FB = COMP 6
FB input bias current 18 100 nA VFB = 1.2 V 6
Nominal oscillator frequency (LM25088-2) fnom1 180 200 220 kHz RRT = 31.6 kΩ 6
Nominal oscillator frequency (LM25088-2) fnom2 430 500 565 kHz RRT = 11.3 kΩ 6
Forced HG off time THG(OFF) 185 280 365 ns 6
Minimum HG on time TON(MIN) 55 ns VVIN = 36 V 6
SYNC positive threshold 2.3 V 7
SYNC pulse width 15 150 ns 7
Cycle-by-cycle sense voltage threshold VCS(TH) 112 120 136 mV VRAMP = 0 V 7
Cycle-by-cycle current limit delay 280 ns VRAMP = 2.5 V 7
Buck switch VDS protection 1.5 V VIN to SW 7
RES threshold upper (rising) Vresup 1.1 1.2 1.3 V VCS = 0.125 7
RES threshold lower (falling) Vresdown 0.1 0.2 0.3 V 7
Charge source current Icharge 40 50 65 µA VCS ≥ 0.125 7
Discharge sink current Idischarge 20 27 34 µA VCS < 0.125 7
Discharge sink current (post fault) Irampdown 0.8 1.2 1.6 µA 7
RAMP current 1 IRAMP1 135 165 195 µA VVIN = 36 V, VOUT = 10 V 7
RAMP current 2 IRAMP2 18 25 30 µA VVIN = 10 V, VOUT = 10 V 7
RAMP output low voltage 200 mV VVIN = 36 V, VOUT = 10 V 7
HG low-state output voltage VOLH 115 215 mV IHG = 100 mA 7
HG High-state output voltage VOHH 240 mV IHG = -100 mA, VOHH = VBOOT, VHG 7
HG rise time 12 ns Cload = 1000 pF 7
HG fall time 6 ns Cload = 1000 pF 7
Peak HG Source Current IOHH 1.5 A VHG = 0V 7
Peak HG sink current IOLH 2 A VHG = VVCC 7
BOOT UVLO 3 V BOOT to SW 7
Thermal shutdown temperature TSD 165 °C Junction temperature rising 7
Thermal shutdown hysteresis 25 °C Junction temperature falling 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper power ground connections (CSS, RT, CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to topside copper area covering the entire underside of the device. Plac 30

CAD (KiCad official)

  • Symbol: LM25088MHX-2
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm25088mhx-2-etched.step / lm25088mhx-2-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm25088mhx-2.step / lm25088mhx-2.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (40 pp, sha256 ab400bb1a40c7ec0, retrieved 2026-11-02, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF