Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LM25088MHX-2
Texas Instruments · DC-DC Controllers · HTSSOP-16-EP
LM25088MHX-2 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | IC supply voltage with an operating range of 4.5 V to 42 V. |
| 2 | EN | input | Below 0.4 V puts the regulator in low power state, 0.4 V to 1.2 V selects standby, and above 1.2 V enables the controller; a 5-µA pullup forces it high when left open. |
| 3 | SS | passive | Soft-start pin charged by an internal 11-µA source to set start-up rate, held low in standby, VCC UV and thermal shutdown, and usable for tracking below the 1.2-V reference. |
| 4 | RAMP | passive | An external capacitor between RAMP and GND sets the emulated current ramp slope, with a recommended range of 100 pF to 2000 pF. |
| 5 | RT/SYNC | input | A single resistor to GND sets the oscillator from 50 kHz to 1 MHz, and an external sync signal higher in frequency than the programmed rate can be applied through a small coupling capacitor. |
| 6 | GND | power_in | Ground return for the controller. |
| 7 | COMP | output | Output of the internal error amplifier, to which the loop compensation network must be connected between COMP and FB. |
| 8 | FB | input | Inverting input of the internal error amplifier with a regulation threshold of 1.205 V. |
| 9 | OUT | input | Output voltage connection that must be connected directly to the regulated output voltage. |
| 10 | RES | passive | Hiccup mode restart capacitor pin (LM25088-2 only) that times hiccup current limiting, with the HG drive disabled when RES reaches 1.2 V and normal operation resuming below 0.2 V. |
| 11 | CSG | passive | Current sense ground serving as the low-side reference for the current sense resistor. |
| 12 | CS | input | Current measurement connection for the re-circulating diode, sensed through an external resistor and an internal sample-and-hold at the end of the buck off time. |
| 13 | SW | passive | Switching node that connects to the source terminal of the external MOSFET switch. |
| 14 | HG | output | High-side gate drive output that connects to the gate terminal of the external MOSFET switch. |
| 15 | BOOT | power_in | Bootstrap capacitor input that requires an external capacitor between BOOT and SW, charged from VCC through an internal diode during the buck off time. |
| 16 | VCC | power_out | Bias regulator output that tracks VIN up to 7.8 V typical and requires a 0.1-µF to 10-µF decoupling capacitor, with an external supply of 8.3 V to 13 V accepted to reduce dissipation. |
| 17 | EP | passive | Exposed pad that is electrically isolated and must be soldered to the ground plane to reduce thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, VOUT to GND | VIN, VOUT | 45 | V | 5 | |||
| BOOT to GND | BOOT | 60 | V | 5 | |||
| SW to GND | SW | -2 | 45 | V | 5 | ||
| VCC to GND | VCC | -0.3 | 16 | V | 5 | ||
| HG to SW | HG | -0.3 | V | 5 | |||
| EN to GND | EN | 14 | V | 5 | |||
| BOOT to SW | BOOT-SW | -0.3 | 16 | V | 5 | ||
| CS, CSG to GND | CS, CSG | -0.3 | 0.3 | V | 5 | ||
| All other inputs to GND | -0.3 | 7 | V | 5 | |||
| Junction temperature | TJ | 150 | °C | 5 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| VIN voltage | VIN | 4.5 | 42 | V | 5 | ||
| VCC voltage (externally supplied) | VCC | 8.3 | 13 | V | 5 | ||
| Operation junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 40 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 6 | °C/W | 5 | |||
| VIN operating current | IBIAS | 4.5 | mA | VFB = 1.3 V | 6 | ||
| VIN standby current | ISTANDBY | 3 | mA | VEN = 1 V | 6 | ||
| VIN shutdown current | ISHUTDOWN | 24 | µA | VEN = 0 V | 6 | ||
| VCC regulation | VVCC(Reg) | 7.4 | 7.8 | 8.2 | V | VVCC = open | 6 |
| VCC sourcing current limit | 25 | 30 | mA | VVCC = 0 | 6 | ||
| VCC undervoltage lockout threshold | VVCC(UV) | 3.7 | 4 | 4.2 | V | Positive going VVCC | 6 |
| VCC undervoltage hysteresis | 200 | mV | 6 | ||||
| EN shutdown threshold | 320 | 400 | 480 | mV | VEN rising | 6 | |
| EN shutdown hysteresis | 100 | mV | VEN falling | 6 | |||
| EN standby threshold | 1.1 | 1.2 | 1.3 | V | VEN rising | 6 | |
| EN standby hysteresis | 120 | mV | VEN falling | 6 | |||
| EN pullup current source | 5 | µA | VEN = 0 V | 6 | |||
| SS pullup current | 8 | 11 | 13 | µA | Source VSS = 0 V | 6 | |
| FB to SS offset | 150 | mV | VFB = 1.3 V | 6 | |||
| FB reference voltage | VREF | 1.187 | 1.205 | 1.223 | V | Measured at FB pin, FB = COMP | 6 |
| FB input bias current | 18 | 100 | nA | VFB = 1.2 V | 6 | ||
| Nominal oscillator frequency (LM25088-2) | fnom1 | 180 | 200 | 220 | kHz | RRT = 31.6 kΩ | 6 |
| Nominal oscillator frequency (LM25088-2) | fnom2 | 430 | 500 | 565 | kHz | RRT = 11.3 kΩ | 6 |
| Forced HG off time | THG(OFF) | 185 | 280 | 365 | ns | 6 | |
| Minimum HG on time | TON(MIN) | 55 | ns | VVIN = 36 V | 6 | ||
| SYNC positive threshold | 2.3 | V | 7 | ||||
| SYNC pulse width | 15 | 150 | ns | 7 | |||
| Cycle-by-cycle sense voltage threshold | VCS(TH) | 112 | 120 | 136 | mV | VRAMP = 0 V | 7 |
| Cycle-by-cycle current limit delay | 280 | ns | VRAMP = 2.5 V | 7 | |||
| Buck switch VDS protection | 1.5 | V | VIN to SW | 7 | |||
| RES threshold upper (rising) | Vresup | 1.1 | 1.2 | 1.3 | V | VCS = 0.125 | 7 |
| RES threshold lower (falling) | Vresdown | 0.1 | 0.2 | 0.3 | V | 7 | |
| Charge source current | Icharge | 40 | 50 | 65 | µA | VCS ≥ 0.125 | 7 |
| Discharge sink current | Idischarge | 20 | 27 | 34 | µA | VCS < 0.125 | 7 |
| Discharge sink current (post fault) | Irampdown | 0.8 | 1.2 | 1.6 | µA | 7 | |
| RAMP current 1 | IRAMP1 | 135 | 165 | 195 | µA | VVIN = 36 V, VOUT = 10 V | 7 |
| RAMP current 2 | IRAMP2 | 18 | 25 | 30 | µA | VVIN = 10 V, VOUT = 10 V | 7 |
| RAMP output low voltage | 200 | mV | VVIN = 36 V, VOUT = 10 V | 7 | |||
| HG low-state output voltage | VOLH | 115 | 215 | mV | IHG = 100 mA | 7 | |
| HG High-state output voltage | VOHH | 240 | mV | IHG = -100 mA, VOHH = VBOOT, VHG | 7 | ||
| HG rise time | 12 | ns | Cload = 1000 pF | 7 | |||
| HG fall time | 6 | ns | Cload = 1000 pF | 7 | |||
| Peak HG Source Current | IOHH | 1.5 | A | VHG = 0V | 7 | ||
| Peak HG sink current | IOLH | 2 | A | VHG = VVCC | 7 | ||
| BOOT UVLO | 3 | V | BOOT to SW | 7 | |||
| Thermal shutdown temperature | TSD | 165 | °C | Junction temperature rising | 7 | ||
| Thermal shutdown hysteresis | 25 | °C | Junction temperature falling | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | power ground connections (CSS, RT, CRAMP) directly to the regulator GND pin. Connect the GND pin and PGND pins together through to topside copper area covering the entire underside of the device. Plac | 30 |
CAD (KiCad official)
- Symbol:
LM25088MHX-2 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm25088mhx-2-etched.step/lm25088mhx-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm25088mhx-2.step/lm25088mhx-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
ab400bb1a40c7ec0, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).