main
History Download
Ray Publish 0.1.0 898a13a

LM20134MHE

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM20134MHE from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SS/TRK bidirectional Soft-start or tracking control input, where an internal 5 µA source charges the external capacitor and an external source below 800 mV overrides the internal reference.
2 FB input Feedback input to the inverting input of the error amplifier, where the internal 800 mV reference sets the regulation voltage at this pin.
3 PGOOD output Open-drain power good output that indicates the output is regulating within tolerance, with a pull-up of 10 kΩ to 100 kΩ recommended.
4 COMP passive External compensation pin, where an RC network (and optional CC2) connects to compensate the device.
5 NC unconnected This pin must be connected to GND to ensure proper operation.
6 PVIN power_in Input voltage to the internal power switches, operating from 2.95 V to 5.5 V, with pins 6 and 7 connected together at the device and a low-ESR capacitor placed nearby.
7 PVIN power_in Input voltage to the internal power switches, operating from 2.95 V to 5.5 V, with pins 6 and 7 connected together at the device and a low-ESR capacitor placed nearby.
8 SW output PWM output of the internal power switches (switch node), with pins 8 and 9 connected together.
9 SW output PWM output of the internal power switches (switch node), with pins 8 and 9 connected together.
10 PGND power_in Power ground for the internal power switches.
11 PGND power_in Power ground for the internal power switches.
12 EN input Precision enable input with a 1.18 V typical rising threshold and 66 mV hysteresis, which should be connected to PVIN if not used.
13 VCC power_out Internal 2.7 V sub-regulator output that should be bypassed with a 1 µF ceramic capacitor.
14 AVIN power_in Analog input supply that generates the internal bias and must be connected to VIN through a low-pass RC filter.
15 AGND power_in Quiet analog ground for the internal bias circuitry, which should be connected to PGND under the exposed pad.
16 SYNC input Frequency synchronization input accepting an external clock from 500 kHz to 1.5 MHz, with logic high above 2.0 V and logic low below 0.8 V, and the device runs at about 410 kHz if left open.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Feedback pin voltage VFB 0.788 0.8 0.812 V VIN = 2.95V to 5.5V 4
Switch Current Limit Threshold ICL 5.8 6.4 7.9 A VIN = 3.3V 4
High-Side Switch On Resistance RDS_ON 36 55 mΩ ISW = 3.5A 4
Low-Side Switch On Resistance RDS_ON 32 52 mΩ ISW = 3.5A 4
Operating Quiescent Current IQ 3.5 6 mA Non-switching, VFB = VCOMP 4
Shutdown Quiescent current ISD 90 180 µA VEN = 0V 4
VIN Under Voltage Lockout Rising VUVLO 2.45 2.7 2.95 V 4
VIN Under Voltage Lockout Hysteresis VUVLO_HYS 45 100 mV Falling VIN 4
VCC Voltage VVCC 2.45 2.7 2.95 V IVCC = 0 µA 4
Soft-Start Pin Source Current ISS 2 4.5 7 µA VSS/TRK = 0V 4
SS/TRK Accuracy, VSS - VFB VTRACK -10 3 15 mV VSS/TRK = 0.4V 4
Oscillator Frequency FOSC 360 410 460 kHz VSYNC = Static 4
Maximum SYNC Frequency FOSCH 1500 kHz 4
Minimum SYNC Frequency FOSCL 460 kHz 4
SYNC pin Logic High VIH_SYNC 2 V 4
SYNC pin Logic Low VIL_SYNC 0.8 V 4
Maximum Duty Cycle DCMAX 85 % ILOAD = 0A 4
Minimum On Time TON_TIME 100 ns 4
Feedback pin bias current IFB 1 100 nA VFB = 0.8V 4
COMP Output Source Current ICOMP_SRC 80 100 µA VFB = VCOMP = 0.6V 4
COMP Output Sink Current ICOMP_SNK 80 100 µA VFB = 1.0V, VCOMP = 0.6V 4
Error Amplifier Transconductance gm 450 510 600 µmho ICOMP = ± 50 µA 4
Over Voltage Protection Rising Threshold VOVP 105 108 111 % With respect to VFB 4
Over Voltage Protection Hysteresis VOVP_HYS 2 3 % 4
PGOOD Rising Threshold VPGTH 92 94 96 % With respect to VFB 4
PGOOD Falling Hysteresis VPGHYS 2 3 % 4
PGOOD Low Sink Current IOL 0.6 1 mA VPGOOD = 0.4V 4
PGOOD High Leakage Current IOH 5 100 nA VPGOOD = 5V 4
EN Pin Turn on Threshold VIH_EN 1.08 1.18 1.28 V VEN Rising 4
Voltages from the indicated pins to GND (AVIN, PVIN, EN, PGOOD, SS/TRK, COMP, FB, SW, SYNC) -0.3 6 V Pins to GND 3
Storage Temperature -65 150 °C 3
Junction Temperature 150 °C 3
Power Dissipation 2.6 W TA = 25°C, θJA = 38°C/W, TJ_MAX = 125°C (footnote 2) 3
Lead Temperature (Soldering, 10 sec) 260 °C Soldering, 10 sec 3
Minimum ESD Rating -2 2 kV Human body model, 100 pF through 1.5 kΩ 3
PVIN, AVIN to GND 2.95 5.5 V 3
Junction Temperature (operating) -40 125 °C 3
Junction to Ambient Thermal Resistance θJA 38 °C/W 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 2. Minimize the copper area of the switch node. Since the LM20134 has the SW pins on opposite sides of the 22

CAD (KiCad official)

  • Symbol: LM20134MHE
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm20134mhe-etched.step / lm20134mhe-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm20134mhe.step / lm20134mhe.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (34 pp, sha256 97bd99f958fd8986, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF