3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLM20134MHE
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM20134MHE from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS/TRK | bidirectional | Soft-start or tracking control input, where an internal 5 µA source charges the external capacitor and an external source below 800 mV overrides the internal reference. |
| 2 | FB | input | Feedback input to the inverting input of the error amplifier, where the internal 800 mV reference sets the regulation voltage at this pin. |
| 3 | PGOOD | output | Open-drain power good output that indicates the output is regulating within tolerance, with a pull-up of 10 kΩ to 100 kΩ recommended. |
| 4 | COMP | passive | External compensation pin, where an RC network (and optional CC2) connects to compensate the device. |
| 5 | NC | unconnected | This pin must be connected to GND to ensure proper operation. |
| 6 | PVIN | power_in | Input voltage to the internal power switches, operating from 2.95 V to 5.5 V, with pins 6 and 7 connected together at the device and a low-ESR capacitor placed nearby. |
| 7 | PVIN | power_in | Input voltage to the internal power switches, operating from 2.95 V to 5.5 V, with pins 6 and 7 connected together at the device and a low-ESR capacitor placed nearby. |
| 8 | SW | output | PWM output of the internal power switches (switch node), with pins 8 and 9 connected together. |
| 9 | SW | output | PWM output of the internal power switches (switch node), with pins 8 and 9 connected together. |
| 10 | PGND | power_in | Power ground for the internal power switches. |
| 11 | PGND | power_in | Power ground for the internal power switches. |
| 12 | EN | input | Precision enable input with a 1.18 V typical rising threshold and 66 mV hysteresis, which should be connected to PVIN if not used. |
| 13 | VCC | power_out | Internal 2.7 V sub-regulator output that should be bypassed with a 1 µF ceramic capacitor. |
| 14 | AVIN | power_in | Analog input supply that generates the internal bias and must be connected to VIN through a low-pass RC filter. |
| 15 | AGND | power_in | Quiet analog ground for the internal bias circuitry, which should be connected to PGND under the exposed pad. |
| 16 | SYNC | input | Frequency synchronization input accepting an external clock from 500 kHz to 1.5 MHz, with logic high above 2.0 V and logic low below 0.8 V, and the device runs at about 410 kHz if left open. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback pin voltage | VFB | 0.788 | 0.8 | 0.812 | V | VIN = 2.95V to 5.5V | 4 |
| Switch Current Limit Threshold | ICL | 5.8 | 6.4 | 7.9 | A | VIN = 3.3V | 4 |
| High-Side Switch On Resistance | RDS_ON | 36 | 55 | mΩ | ISW = 3.5A | 4 | |
| Low-Side Switch On Resistance | RDS_ON | 32 | 52 | mΩ | ISW = 3.5A | 4 | |
| Operating Quiescent Current | IQ | 3.5 | 6 | mA | Non-switching, VFB = VCOMP | 4 | |
| Shutdown Quiescent current | ISD | 90 | 180 | µA | VEN = 0V | 4 | |
| VIN Under Voltage Lockout Rising | VUVLO | 2.45 | 2.7 | 2.95 | V | 4 | |
| VIN Under Voltage Lockout Hysteresis | VUVLO_HYS | 45 | 100 | mV | Falling VIN | 4 | |
| VCC Voltage | VVCC | 2.45 | 2.7 | 2.95 | V | IVCC = 0 µA | 4 |
| Soft-Start Pin Source Current | ISS | 2 | 4.5 | 7 | µA | VSS/TRK = 0V | 4 |
| SS/TRK Accuracy, VSS - VFB | VTRACK | -10 | 3 | 15 | mV | VSS/TRK = 0.4V | 4 |
| Oscillator Frequency | FOSC | 360 | 410 | 460 | kHz | VSYNC = Static | 4 |
| Maximum SYNC Frequency | FOSCH | 1500 | kHz | 4 | |||
| Minimum SYNC Frequency | FOSCL | 460 | kHz | 4 | |||
| SYNC pin Logic High | VIH_SYNC | 2 | V | 4 | |||
| SYNC pin Logic Low | VIL_SYNC | 0.8 | V | 4 | |||
| Maximum Duty Cycle | DCMAX | 85 | % | ILOAD = 0A | 4 | ||
| Minimum On Time | TON_TIME | 100 | ns | 4 | |||
| Feedback pin bias current | IFB | 1 | 100 | nA | VFB = 0.8V | 4 | |
| COMP Output Source Current | ICOMP_SRC | 80 | 100 | µA | VFB = VCOMP = 0.6V | 4 | |
| COMP Output Sink Current | ICOMP_SNK | 80 | 100 | µA | VFB = 1.0V, VCOMP = 0.6V | 4 | |
| Error Amplifier Transconductance | gm | 450 | 510 | 600 | µmho | ICOMP = ± 50 µA | 4 |
| Over Voltage Protection Rising Threshold | VOVP | 105 | 108 | 111 | % | With respect to VFB | 4 |
| Over Voltage Protection Hysteresis | VOVP_HYS | 2 | 3 | % | 4 | ||
| PGOOD Rising Threshold | VPGTH | 92 | 94 | 96 | % | With respect to VFB | 4 |
| PGOOD Falling Hysteresis | VPGHYS | 2 | 3 | % | 4 | ||
| PGOOD Low Sink Current | IOL | 0.6 | 1 | mA | VPGOOD = 0.4V | 4 | |
| PGOOD High Leakage Current | IOH | 5 | 100 | nA | VPGOOD = 5V | 4 | |
| EN Pin Turn on Threshold | VIH_EN | 1.08 | 1.18 | 1.28 | V | VEN Rising | 4 |
| Voltages from the indicated pins to GND (AVIN, PVIN, EN, PGOOD, SS/TRK, COMP, FB, SW, SYNC) | -0.3 | 6 | V | Pins to GND | 3 | ||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| Power Dissipation | 2.6 | W | TA = 25°C, θJA = 38°C/W, TJ_MAX = 125°C (footnote 2) | 3 | |||
| Lead Temperature (Soldering, 10 sec) | 260 | °C | Soldering, 10 sec | 3 | |||
| Minimum ESD Rating | -2 | 2 | kV | Human body model, 100 pF through 1.5 kΩ | 3 | ||
| PVIN, AVIN to GND | 2.95 | 5.5 | V | 3 | |||
| Junction Temperature (operating) | -40 | 125 | °C | 3 | |||
| Junction to Ambient Thermal Resistance | θJA | 38 | °C/W | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 2. Minimize the copper area of the switch node. Since the LM20134 has the SW pins on opposite sides of the | 22 |
CAD (KiCad official)
- Symbol:
LM20134MHE - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm20134mhe-etched.step/lm20134mhe-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm20134mhe.step/lm20134mhe.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (34 pp, sha256
97bd99f958fd8986, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).