main
Ray
Publish 0.1.0
4a1581a
LIS2HH12TR
STMicroelectronics · Accelerometers · LGA-12(2x2)
LIS2HH12TR from STMicroelectronics, in a LGA-12(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL/SPC | input | I2C serial clock (SCL) or SPI serial port clock (SPC), which must be pulled up to Vdd_IO through an external resistor when used for I2C. |
| 2 | CS | input | Selects the interface mode: high (1) gives SPI idle mode with I2C enabled, low (0) gives SPI communication with I2C disabled, and it must be tied high to Vdd_IO to use I2C. |
| 3 | SDO/SA0 | tri_state | Serves as the I2C least significant bit of the device address (SA0) or the SPI serial data output (SDO), with the address 0011101b when tied to supply and 0011110b when tied to ground. |
| 4 | SDA/SDI/SDO | bidirectional | Serves as the I2C serial data line (SDA), which must be pulled up to Vdd_IO through an external resistor, or as SPI serial data input (SDI) or 3-wire interface serial data output (SDO). |
| 5 | RES | passive | Reserved pin that must be connected to GND. |
| 6 | GND | power_in | 0 V supply ground pin. |
| 7 | GND | power_in | 0 V supply ground pin. |
| 8 | GND | power_in | 0 V supply ground pin. |
| 9 | Vdd | power_in | Main power supply, with an operational range of 1.71 V to 3.6 V (2.5 V typical calibration point). |
| 10 | Vdd_IO | power_in | Power supply for the I/O pins, from 1.71 V up to Vdd+0.1 V, and it can remain powered while Vdd is removed without blocking the communication buses. |
| 11 | INT2 | output | Interrupt pin 2 output from the sensor's interrupt generator. |
| 12 | INT1 | output | Interrupt pin 1 output from the sensor's interrupt generator. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LGA-12(2x2) |
| Category | Sensors |
| Pins | 12 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Self-test positive difference | ST | 70 | 1500 | mg | OUTPUT(ST2,ST1=01) - OUTPUT(ST2,ST1=00) | 10 | |
| Operating temperature range | Top | -40 | 85 | °C | 11 | ||
| Supply voltage | Vdd | 1.71 | 2.5 | 3.6 | V | 11 | |
| I/O pins supply voltage | Vdd_IO | 1.71 | V | maximum printed as Vdd+0.1 V | 11 | ||
| Zero-g level offset accuracy | TyOff | -30 | 30 | mg | Typical zero-g level offset accuracy | 10 | |
| Zero-g level change vs. temperature | TCOff | -0.25 | 0.25 | mg/°C | Delta from 25 °C | 10 | |
| SPI SPC clock cycle | tc(SPC) | 100 | ns | 12 | |||
| SPI SPC clock frequency | fc(SPC) | 10 | MHz | 12 | |||
| SPI CS setup time | tsu(CS) | 6 | ns | 12 | |||
| SPI CS hold time | th(CS) | 8 | ns | 12 | |||
| SPI SDI input setup time | tsu(SI) | 5 | ns | 12 | |||
| SPI SDI input hold time | th(SI) | 15 | ns | 12 | |||
| SPI SDO valid output time | tv(SO) | 50 | ns | 12 | |||
| SPI SDO output hold time | th(SO) | 9 | ns | 12 | |||
| SPI SDO output disable time | tdis(SO) | 50 | ns | 12 | |||
| SCL clock frequency | f(SCL) | 0 | 100 | kHz | I2C standard mode | 13 | |
| SCL clock frequency | f(SCL) | 0 | 400 | kHz | I2C fast mode | 13 | |
| SCL clock low time | tw(SCLL) | 4.7 | µs | I2C standard mode | 13 | ||
| SCL clock low time | tw(SCLL) | 1.3 | µs | I2C fast mode | 13 | ||
| SCL clock high time | tw(SCLH) | 4 | µs | I2C standard mode | 13 | ||
| SCL clock high time | tw(SCLH) | 0.6 | µs | I2C fast mode | 13 | ||
| SDA setup time | tsu(SDA) | 250 | ns | I2C standard mode | 13 | ||
| SDA setup time | tsu(SDA) | 100 | ns | I2C fast mode | 13 | ||
| SDA data hold time | th(SDA) | 0.01 | 3.45 | µs | I2C standard mode | 13 | |
| SDA data hold time | th(SDA) | 0.01 | 0.9 | µs | I2C fast mode | 13 | |
| START condition hold time | th(ST) | 4 | µs | I2C standard mode | 13 | ||
| START condition hold time | th(ST) | 0.6 | µs | I2C fast mode | 13 | ||
| Repeated START condition setup time | tsu(SR) | 4.7 | µs | I2C standard mode | 13 | ||
| Repeated START condition setup time | tsu(SR) | 0.6 | µs | I2C fast mode | 13 | ||
| STOP condition setup time | tsu(SP) | 4 | µs | I2C standard mode | 13 | ||
| STOP condition setup time | tsu(SP) | 0.6 | µs | I2C fast mode | 13 | ||
| Bus free time between STOP and START condition | tw(SP:SR) | 4.7 | µs | I2C standard mode | 13 | ||
| Bus free time between STOP and START condition | tw(SP:SR) | 1.3 | µs | I2C fast mode | 13 | ||
| Supply voltage | Vdd | -0.3 | 4.8 | V | 14 | ||
| I/O pins supply voltage | Vdd_IO | -0.3 | 4.8 | V | 14 | ||
| Input voltage on any control pin | Vin | -0.3 | V | CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0; maximum printed as Vdd_IO +0.3 V | 14 | ||
| Acceleration (powered) | APOW | 3000 | g | any axis, powered, Vdd = 2.5 V, 0.5 ms | 14 | ||
| Acceleration (powered) | APOW | 10000 | g | any axis, powered, Vdd = 2.5 V, 0.2 ms | 14 | ||
| Acceleration (unpowered) | AUNP | 3000 | g | any axis, unpowered, 0.5 ms | 14 | ||
| Acceleration (unpowered) | AUNP | 10000 | g | any axis, unpowered, 0.2 ms | 14 | ||
| Operating temperature range | TOP | -40 | 85 | °C | 14 | ||
| Storage temperature range | TSTG | -40 | 125 | °C | 14 | ||
| Electrostatic discharge protection | ESD | 2 | kV | HBM | 14 | ||
| Sensitivity | So | 0.061 | mg/digit | @ FS ±2.0 g | 10 | ||
| Sensitivity | So | 0.122 | mg/digit | @ FS ±4.0 g | 10 | ||
| Sensitivity | So | 0.244 | mg/digit | @ FS ±8.0 g | 10 | ||
| Sensitivity change vs. temperature | TCSo | 0.01 | %/°C | 10 | |||
| Turn-on time, samples discarded | Ton | 1 | # of samples | CTRL4 (23h) (BW_SCALE_ODR) = 0 | 10 | ||
| Current consumption in active mode | IddA | 180 | µA | ODR 100-800 Hz | 11 | ||
| Current consumption in active mode | IddA | 110 | µA | ODR 50 Hz | 11 | ||
| Current consumption in active mode | IddA | 50 | µA | ODR 10 Hz | 11 | ||
| Current consumption in power-down mode | IddPdn | 5 | µA | 11 | |||
| Boot time | Tboot | 20 | ms | Time from Vdd on until all configuration and calibration parameters are loaded | 11 | ||
| Temperature sensor output change vs. temperature | TSDr | 8 | digit/°C | 11-bit resolution | 11 | ||
| Temperature refresh rate | TODR | 10 | Hz | 11 |
CAD (KiCad official)
- Symbol:
LIS2HH12TR - Footprint:
Package_LGA:LGA-12_2x2mm_P0.5mm - 3D model: LGA-12(2x2) (KiCad packages3D, STEP)
- 3D model files:
lis2hh12tr-etched.step/lis2hh12tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lis2hh12tr.step/lis2hh12tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (47 pp, sha256
f73c1d52de1bf963, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LIS2HH12TR
**STMicroelectronics** · Accelerometers · LGA-12(2x2)
LIS2HH12TR from STMicroelectronics, in a LGA-12(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL/SPC | input | I2C serial clock (SCL) or SPI serial port clock (SPC), which must be pulled up to Vdd_IO through an external resistor when used for I2C. |
| 2 | CS | input | Selects the interface mode: high (1) gives SPI idle mode with I2C enabled, low (0) gives SPI communication with I2C disabled, and it must be tied high to Vdd_IO to use I2C. |
| 3 | SDO/SA0 | tri_state | Serves as the I2C least significant bit of the device address (SA0) or the SPI serial data output (SDO), with the address 0011101b when tied to supply and 0011110b when tied to ground. |
| 4 | SDA/SDI/SDO | bidirectional | Serves as the I2C serial data line (SDA), which must be pulled up to Vdd_IO through an external resistor, or as SPI serial data input (SDI) or 3-wire interface serial data output (SDO). |
| 5 | RES | passive | Reserved pin that must be connected to GND. |
| 6 | GND | power_in | 0 V supply ground pin. |
| 7 | GND | power_in | 0 V supply ground pin. |
| 8 | GND | power_in | 0 V supply ground pin. |
| 9 | Vdd | power_in | Main power supply, with an operational range of 1.71 V to 3.6 V (2.5 V typical calibration point). |
| 10 | Vdd_IO | power_in | Power supply for the I/O pins, from 1.71 V up to Vdd+0.1 V, and it can remain powered while Vdd is removed without blocking the communication buses. |
| 11 | INT2 | output | Interrupt pin 2 output from the sensor's interrupt generator. |
| 12 | INT1 | output | Interrupt pin 1 output from the sensor's interrupt generator. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LGA-12(2x2) |
| Category | Sensors |
| Pins | 12 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Self-test positive difference | ST | 70 | | 1500 | mg | OUTPUT(ST2,ST1=01) - OUTPUT(ST2,ST1=00) | 10 |
| Operating temperature range | Top | -40 | | 85 | °C | | 11 |
| Supply voltage | Vdd | 1.71 | 2.5 | 3.6 | V | | 11 |
| I/O pins supply voltage | Vdd_IO | 1.71 | | | V | maximum printed as Vdd+0.1 V | 11 |
| Zero-g level offset accuracy | TyOff | -30 | | 30 | mg | Typical zero-g level offset accuracy | 10 |
| Zero-g level change vs. temperature | TCOff | -0.25 | | 0.25 | mg/°C | Delta from 25 °C | 10 |
| SPI SPC clock cycle | tc(SPC) | 100 | | | ns | | 12 |
| SPI SPC clock frequency | fc(SPC) | | | 10 | MHz | | 12 |
| SPI CS setup time | tsu(CS) | 6 | | | ns | | 12 |
| SPI CS hold time | th(CS) | 8 | | | ns | | 12 |
| SPI SDI input setup time | tsu(SI) | 5 | | | ns | | 12 |
| SPI SDI input hold time | th(SI) | 15 | | | ns | | 12 |
| SPI SDO valid output time | tv(SO) | | | 50 | ns | | 12 |
| SPI SDO output hold time | th(SO) | 9 | | | ns | | 12 |
| SPI SDO output disable time | tdis(SO) | | | 50 | ns | | 12 |
| SCL clock frequency | f(SCL) | 0 | | 100 | kHz | I2C standard mode | 13 |
| SCL clock frequency | f(SCL) | 0 | | 400 | kHz | I2C fast mode | 13 |
| SCL clock low time | tw(SCLL) | 4.7 | | | µs | I2C standard mode | 13 |
| SCL clock low time | tw(SCLL) | 1.3 | | | µs | I2C fast mode | 13 |
| SCL clock high time | tw(SCLH) | 4 | | | µs | I2C standard mode | 13 |
| SCL clock high time | tw(SCLH) | 0.6 | | | µs | I2C fast mode | 13 |
| SDA setup time | tsu(SDA) | 250 | | | ns | I2C standard mode | 13 |
| SDA setup time | tsu(SDA) | 100 | | | ns | I2C fast mode | 13 |
| SDA data hold time | th(SDA) | 0.01 | | 3.45 | µs | I2C standard mode | 13 |
| SDA data hold time | th(SDA) | 0.01 | | 0.9 | µs | I2C fast mode | 13 |
| START condition hold time | th(ST) | 4 | | | µs | I2C standard mode | 13 |
| START condition hold time | th(ST) | 0.6 | | | µs | I2C fast mode | 13 |
| Repeated START condition setup time | tsu(SR) | 4.7 | | | µs | I2C standard mode | 13 |
| Repeated START condition setup time | tsu(SR) | 0.6 | | | µs | I2C fast mode | 13 |
| STOP condition setup time | tsu(SP) | 4 | | | µs | I2C standard mode | 13 |
| STOP condition setup time | tsu(SP) | 0.6 | | | µs | I2C fast mode | 13 |
| Bus free time between STOP and START condition | tw(SP:SR) | 4.7 | | | µs | I2C standard mode | 13 |
| Bus free time between STOP and START condition | tw(SP:SR) | 1.3 | | | µs | I2C fast mode | 13 |
| Supply voltage | Vdd | -0.3 | | 4.8 | V | | 14 |
| I/O pins supply voltage | Vdd_IO | -0.3 | | 4.8 | V | | 14 |
| Input voltage on any control pin | Vin | -0.3 | | | V | CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0; maximum printed as Vdd_IO +0.3 V | 14 |
| Acceleration (powered) | APOW | | | 3000 | g | any axis, powered, Vdd = 2.5 V, 0.5 ms | 14 |
| Acceleration (powered) | APOW | | | 10000 | g | any axis, powered, Vdd = 2.5 V, 0.2 ms | 14 |
| Acceleration (unpowered) | AUNP | | | 3000 | g | any axis, unpowered, 0.5 ms | 14 |
| Acceleration (unpowered) | AUNP | | | 10000 | g | any axis, unpowered, 0.2 ms | 14 |
| Operating temperature range | TOP | -40 | | 85 | °C | | 14 |
| Storage temperature range | TSTG | -40 | | 125 | °C | | 14 |
| Electrostatic discharge protection | ESD | | | 2 | kV | HBM | 14 |
| Sensitivity | So | | 0.061 | | mg/digit | @ FS ±2.0 g | 10 |
| Sensitivity | So | | 0.122 | | mg/digit | @ FS ±4.0 g | 10 |
| Sensitivity | So | | 0.244 | | mg/digit | @ FS ±8.0 g | 10 |
| Sensitivity change vs. temperature | TCSo | | 0.01 | | %/°C | | 10 |
| Turn-on time, samples discarded | Ton | | 1 | | # of samples | CTRL4 (23h) (BW_SCALE_ODR) = 0 | 10 |
| Current consumption in active mode | IddA | | 180 | | µA | ODR 100-800 Hz | 11 |
| Current consumption in active mode | IddA | | 110 | | µA | ODR 50 Hz | 11 |
| Current consumption in active mode | IddA | | 50 | | µA | ODR 10 Hz | 11 |
| Current consumption in power-down mode | IddPdn | | 5 | | µA | | 11 |
| Boot time | Tboot | | 20 | | ms | Time from Vdd on until all configuration and calibration parameters are loaded | 11 |
| Temperature sensor output change vs. temperature | TSDr | | 8 | | digit/°C | 11-bit resolution | 11 |
| Temperature refresh rate | TODR | | 10 | | Hz | | 11 |
## CAD (KiCad official)
- Symbol: `LIS2HH12TR`
- Footprint: `Package_LGA:LGA-12_2x2mm_P0.5mm`
- 3D model: LGA-12(2x2) (KiCad packages3D, STEP)
- 3D model files: `lis2hh12tr-etched.step` / `lis2hh12tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lis2hh12tr.step` / `lis2hh12tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/content/ccc/resource/technical/document/datasheet/c9/16/f2/79/ca/31/47/89/DM00096789.pdf/files/DM00096789.pdf/jcr:content/translations/en.DM00096789.pdf) (47 pp, sha256 `f73c1d52de1bf963`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lis2hh12tr-datasheet.pdf)