3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLGS51065EP
Legend-Si · DC-DC Converters · ESOP-8
LGS51065EP from Legend-Si, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Test pin, to be left floating. |
| 2 | EN | input | BUCK enable input that enables the step-down output when high and turns it off when low or left open; it is 3.3V logic level (high threshold 1.4V, low threshold 0.6V), so do not connect high voltage. |
| 3 | GND | power_in | Chip system ground. |
| 4 | VIN | power_in | Input voltage pin (recommended 12V to 65V) with an external input capacitor, not recommended to exceed 100uF. |
| 5 | SW | output | Internal power switch node connected to the external power inductor, Schottky diode and the CBST capacitor. |
| 6 | BST | passive | Power supply for the high-side gate drive; a high quality 100nF ceramic capacitor must be connected between BST and SW. |
| 7 | 3V3 | power_out | LDO regulated fixed 3.3V output rated 10mA, requiring at least 2.2uF external capacitance to ground. |
| 8 | FB | input | Step-down feedback input with multi-mode adaptation: FB impedance to ground above 20K selects constant voltage mode (1V reference, resistor divider) and below 2K selects constant current mode (0.2V across the LED current sense resistor), latched once at power-up. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Legend-Si |
| Package | ESOP-8 |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Pin to GND voltage VI,SW | VI,SW | -0.3 | 65 | V | 3 | ||
| Pin to GND voltage 3V3,E,FB | 3V3,E,FB | -0.3 | 6 | V | 3 | ||
| Pin to GND voltage BST | BST | -0.3 | V | 3 | |||
| Storage temperature | Tstg | -65 | 150 | ℃ | 3 | ||
| Operating temperature | -40 | 125 | ℃ | 3 | |||
| ESD rating HBM | -2000 | 2000 | V | 3 | |||
| ESD rating CDM | -1500 | 1500 | V | 3 | |||
| ESD rating MM | -200 | 200 | V | 3 | |||
| Recommended input voltage range | VI | 12 | 65 | V | 4 | ||
| Input undervoltage lock, rising edge | VUVLO | 12 | 13 | V | Rising edge | 4 | |
| Input undervoltage lock, fall edge | VUVLO | 10 | 10.5 | V | Fall edge | 4 | |
| Quiescent current | IQ | 65 | μA | E =0 | 4 | ||
| BUCK module quiescent current | IQ-BUCK | 125 | μA | E =1, VI =24V, VOUT=5V | 4 | ||
| BUCK top tube RDS(ON) | RDS(ON)BUCK_TOP | 600 | mΩ | TJ=25℃ | 4 | ||
| FB feedback voltage, CV mode | VFB.CV | 1 | V | Voltage stabilized output mode | 4 | ||
| FB feedback voltage, CC mode | VFB.CC | 0.2 | V | Constant current output mode | 4 | ||
| Maximum duty cycle | DMAX | 85 | % | 4 | |||
| Peak SW current limit | ILIMT_SW | 900 | mA | VI =48V | 4 | ||
| FB bias current | IFB.BIASA | 10 | nA | 4 | |||
| LDO output voltage range | VOUT.LDO | 3.2 | 3.3 | 3.6 | V | 4 | |
| LDO output current | IOUT.LDO | 10 | mA | 4 | |||
| LDO protective current limiting | ILIMIT.LDO | 15 | mA | Short to GND | 4 | ||
| Input I/O high logic threshold | VI/O_H | 1.4 | V | Pin E | 4 | ||
| Input I/O low logic threshold | VI/O_L | 0.6 | V | Pin E | 4 | ||
| Over temperature protection threshold | TOTP-R | 150 | ℃ | TJ Rising | 4 | ||
| Release of over temperature protection | TOTP-F | 130 | ℃ | TJ Falling | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | (PI 5) and G D (PI 2) pins to minimize highfrequency noise. ■ For the high current path, use a large copper clad | 20 |
CAD (KiCad official)
- Symbol:
LGS51065EP - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
lgs51065ep-etched.step/lgs51065ep-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lgs51065ep.step/lgs51065ep.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Legend-Si datasheet (22 pp, sha256
74742a5500784094, retrieved 2026-11-04, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).