by adom
A 12,960-LED addressable wall for the Adom workcell: 9 identical 160x160mm tiles (1,440 Dialight 587-1024-147F 2020 LEDs each, RP2040 + USB-C per tile) on a LrgLrg 576x576 scaffold. Remote Adom users each own a pixel.
09550a2
Component register — LED Grid Wall tile (rev A)
| Ref prefix | Part | Role | Wiki page | CAD status |
|---|---|---|---|---|
| D1..D1440 | Dialight 587-1024-147F | 2020 addressable RGB LED (WS2812-compatible, 5mA/ch, no ext cap) | adom/587-1024-147f | page being authored (symbol/footprint/STEP/GLB + provenance) |
| U1 | RP2040 | MCU, 4x PIO WS2812 chains, USB CDC | ray/rp2040 | full CAD ✓ |
| U2 | W25Q128FVSIG | 128Mbit QSPI flash, SOIC-8-208mil | adom/w25q128fvsig | full CAD ✓ |
| U3 | AP2112K-3.3 | 5V→3.3V LDO 600mA SOT-23-5 | adom/ap2112k-3.3 | full CAD ✓ |
| U4 | SN74AHCT125PWR | quad 3.3→5V data buffer, TSSOP-14 | adom/sn74ahct125pwr | full CAD ✓ |
| J1 | TYPE-C-31-M-12 | USB-C 16-pin receptacle (data+power) | adom/type-c-31-m-12 (private, adom org) | full CAD ✓ |
| MP1..MP4 | MachineContactLarge | 5V/GND power entry from scaffold (~20A each) | adom/machinecontactlarge | full CAD ✓ |
| Y1 | X322512MSB4SI | 12MHz crystal SMD3225, CL=20pF | adom/x322512msb4si | GLB only — needs sym/mod/STEP added (KiCad-official footprint) |
| C* | 0402B104J160CT 100nF, 0402X105K250CT 1uF, CL21A476MQYNNNE 47uF, 0402N330J500CT 33pF | decoupling/bulk/crystal load | Adom Basic Parts | full CAD ✓ |
| R* | 0402 27R (CR0402-FX-27R4GLF?) / 5.1k / 10k / 1k | USB series, CC pulldowns, pullups | Adom Basic Parts | full CAD ✓ |
Notes
- Mouser sourcing for the LED: 645-587-1024-147F (20,947 in stock 2026-09-28, $0.37@500). Worldsemi WS2812B-2020 (existing basic part) is out of stock at LCSC/Adom and not Mouser-distributed.
- 3D discrepancy on adom/ws2812b-2020 filed as issue #1581 (not used in this design).
- USB-C page is private to adom org; fine for an internal build. Mark public later if the tile page goes public.
Amendment 2026-09-29 — I2C mesh additions
| MC1..MC2 | MachineContactMedium | I2C SDA/SCL tile interconnect | adom/machinecontactmedium | full CAD ✓ | | R(ADR) | 10k 0402 (CR0402-FX-1002GLF) | address strap pull-ups GPIO4-7 | Adom Basic Parts | ✓ | | R(I2C) | 22k 0402 (CR0402-FX-2232GLF) | I2C bus pull-ups SDA/SCL | Adom Basic Parts | ✓ | | ADR0..3 | 2-pad 0402 solder jumper (bare pads, no part) | tile address straps | board project only | n/a | Architecture: tiles mesh by I2C (400kHz); master tile (address 0) is the only USB-C uplink to the control panel. One board design for all 9 tiles.
# Component register — LED Grid Wall tile (rev A)
| Ref prefix | Part | Role | Wiki page | CAD status |
|---|---|---|---|---|
| D1..D1440 | Dialight 587-1024-147F | 2020 addressable RGB LED (WS2812-compatible, 5mA/ch, no ext cap) | adom/587-1024-147f | **page being authored** (symbol/footprint/STEP/GLB + provenance) |
| U1 | RP2040 | MCU, 4x PIO WS2812 chains, USB CDC | ray/rp2040 | full CAD ✓ |
| U2 | W25Q128FVSIG | 128Mbit QSPI flash, SOIC-8-208mil | adom/w25q128fvsig | full CAD ✓ |
| U3 | AP2112K-3.3 | 5V→3.3V LDO 600mA SOT-23-5 | adom/ap2112k-3.3 | full CAD ✓ |
| U4 | SN74AHCT125PWR | quad 3.3→5V data buffer, TSSOP-14 | adom/sn74ahct125pwr | full CAD ✓ |
| J1 | TYPE-C-31-M-12 | USB-C 16-pin receptacle (data+power) | adom/type-c-31-m-12 (private, adom org) | full CAD ✓ |
| MP1..MP4 | MachineContactLarge | 5V/GND power entry from scaffold (~20A each) | adom/machinecontactlarge | full CAD ✓ |
| Y1 | X322512MSB4SI | 12MHz crystal SMD3225, CL=20pF | adom/x322512msb4si | GLB only — **needs sym/mod/STEP added** (KiCad-official footprint) |
| C* | 0402B104J160CT 100nF, 0402X105K250CT 1uF, CL21A476MQYNNNE 47uF, 0402N330J500CT 33pF | decoupling/bulk/crystal load | Adom Basic Parts | full CAD ✓ |
| R* | 0402 27R (CR0402-FX-27R4GLF?) / 5.1k / 10k / 1k | USB series, CC pulldowns, pullups | Adom Basic Parts | full CAD ✓ |
## Notes
- Mouser sourcing for the LED: 645-587-1024-147F (20,947 in stock 2026-09-28, $0.37@500).
Worldsemi WS2812B-2020 (existing basic part) is out of stock at LCSC/Adom and not Mouser-distributed.
- 3D discrepancy on adom/ws2812b-2020 filed as issue #1581 (not used in this design).
- USB-C page is private to adom org; fine for an internal build. Mark public later if the tile page goes public.
## Amendment 2026-09-29 — I2C mesh additions
| MC1..MC2 | MachineContactMedium | I2C SDA/SCL tile interconnect | adom/machinecontactmedium | full CAD ✓ |
| R(ADR) | 10k 0402 (CR0402-FX-1002GLF) | address strap pull-ups GPIO4-7 | Adom Basic Parts | ✓ |
| R(I2C) | 22k 0402 (CR0402-FX-2232GLF) | I2C bus pull-ups SDA/SCL | Adom Basic Parts | ✓ |
| ADR0..3 | 2-pad 0402 solder jumper (bare pads, no part) | tile address straps | board project only | n/a |
Architecture: tiles mesh by I2C (400kHz); master tile (address 0) is the only USB-C uplink
to the control panel. One board design for all 9 tiles.