main
Ray
Publish 0.1.0
eef0288
LAN9221-ABZJ
Microchip Tech · Ethernet ICs · QFN-56(8x8)
LAN9221-ABZJ from Microchip Tech, in a QFN-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD33REG | power_in | +3.3V power supply for the internal +1.8V regulator. |
| 2 | VDD18CORE | power_out | +1.8V from the internal core regulator; must be tied to pin 37, needs a 0.01uF decoupling capacitor plus a 4.7uF bulk capacitor (<2 Ohm ESR), and must not supply other external devices. |
| 3 | GPIO0/nLED1 | bidirectional | General purpose I/O data (push-pull, open-drain or input via GPIO_CFG) multiplexed with nLED1 open-drain speed indicator, driven low at 100Mb operation. |
| 4 | GPIO1/nLED2 | bidirectional | General purpose I/O data multiplexed with nLED2 open-drain link and activity indicator, driven low on valid link and pulsed high for 80mS on activity. |
| 5 | GPIO2/nLED3 | bidirectional | General purpose I/O data multiplexed with nLED3 open-drain full-duplex indicator, driven low in full-duplex mode. |
| 6 | A7 | input | Host address input bit 7, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored for A[7:3] when FIFO_SEL is high). |
| 7 | A6 | input | Host address input bit 6, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 8 | A5 | input | Host address input bit 5, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 9 | A4 | input | Host address input bit 4, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 10 | A3 | input | Host address input bit 3, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 11 | A2 | input | Host address input bit 2, used with A[7:1] to select internal CSRs and TX/RX FIFOs. |
| 12 | A1 | input | Host address input bit 1, used with A[7:1] to select internal CSRs and TX/RX FIFOs. |
| 13 | FIFO_SEL | input | When driven high all accesses are to the RX or TX Data FIFOs and the A[7:3] address inputs are ignored. |
| 14 | TEST | input | Reserved for internal test; has a 50uA typical internal pull-down, must be grounded or pulled low when VDDVARIO is below 3.0V, and may float at 3.3V. |
| 15 | nRD | input | Active-low read strobe indicating a read cycle. |
| 16 | nWR | input | Active-low write strobe indicating a write cycle; qualified with nCS it also wakes the device from a reduced power state. |
| 17 | nCS | input | Active-low chip select qualifying read and write operations; qualified with nWR it also wakes the device from a reduced power state. |
| 18 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 19 | D15 | bidirectional | Host bi-directional data bit 15. |
| 20 | D14 | bidirectional | Host bi-directional data bit 14. |
| 21 | D13 | bidirectional | Host bi-directional data bit 13. |
| 22 | D12 | bidirectional | Host bi-directional data bit 12. |
| 23 | D11 | bidirectional | Host bi-directional data bit 11. |
| 24 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 25 | D10 | bidirectional | Host bi-directional data bit 10. |
| 26 | D9 | bidirectional | Host bi-directional data bit 9. |
| 27 | D8 | bidirectional | Host bi-directional data bit 8. |
| 28 | D7 | bidirectional | Host bi-directional data bit 7. |
| 29 | D6 | bidirectional | Host bi-directional data bit 6. |
| 30 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 31 | D5 | bidirectional | Host bi-directional data bit 5. |
| 32 | D4 | bidirectional | Host bi-directional data bit 4. |
| 33 | D3 | bidirectional | Host bi-directional data bit 3. |
| 34 | D2 | bidirectional | Host bi-directional data bit 2. |
| 35 | D1 | bidirectional | Host bi-directional data bit 1. |
| 36 | D0 | bidirectional | Host bi-directional data bit 0. |
| 37 | VDD18CORE | power_out | +1.8V from the internal core regulator; must be tied to pin 2, needs a 0.01uF decoupling capacitor, and must not supply other external devices. |
| 38 | EEDIO/GPO3 | bidirectional | Serial EEPROM data I/O (optional) or general purpose output 3 / TX_EN / TX_CLK monitor on the internal MII; cannot function as a general-purpose input. |
| 39 | EECS | output | Serial EEPROM chip select. |
| 40 | EECLK/GPO4 | output | Serial EEPROM clock or general purpose output 4 / RX_DV / RX_CLK monitor; has internal pull-up, must not be pulled or driven low, must be left unconnected if the EEPROM is unused, and needs an external pull-up below 3.0V VDDVARIO. |
| 41 | PME | output | Wakeup indicator asserted on a detected wake event, with programmable polarity and buffer type (push-pull or open-drain). |
| 42 | nRESET | input | Active-low reset input for all logic and registers, with weak internal pull-up; must be pulled high externally or driven when VDDVARIO is below 3.0V. |
| 43 | IRQ | output | Programmable interrupt request with programmable polarity, source and buffer type (push-pull or open-drain). |
| 44 | TPO- | output | Ethernet transmit negative output (normal); becomes receive negative input when reversed by HP Auto-MDIX. |
| 45 | TPO+ | output | Ethernet transmit positive output (normal); becomes receive positive input when reversed by HP Auto-MDIX. |
| 46 | VDD33A | power_in | +3.3V analog power supply. |
| 47 | TPI- | input | Ethernet receive negative input (normal); becomes transmit negative output when reversed by HP Auto-MDIX. |
| 48 | TPI+ | input | Ethernet receive positive input (normal); becomes transmit positive input/output when reversed by HP Auto-MDIX. |
| 49 | VDD33A | power_in | +3.3V analog power supply. |
| 50 | EXRES | passive | PHY external bias resistor pin; must be connected to ground through a 12.4K ohm 1% resistor. |
| 51 | VDD33A | power_in | +3.3V analog power supply. |
| 52 | AMDIX_EN | input | Auto-MDIX enable with internal pull-up: pull high or leave unconnected to enable, pull low to disable; needs an external resistor below 3.0V VDDVARIO. |
| 53 | VDD18A | power_in | +1.8V analog power supply; must be connected externally to VDD18CORE. |
| 54 | XTAL2 | output | External 25MHz crystal output; leave unconnected when XTAL1/CLKIN is driven by a single-ended oscillator. |
| 55 | XTAL1/CLKIN | input | External 25MHz crystal input, or single-ended TTL oscillator input (CLKIN). |
| 56 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 57 | VSS | power_in | Common ground exposed pad on bottom of package; must be connected to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-56(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 57 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDVARIO, VDD33REG, VDD33A absolute maximum | 0 | 3.6 | V | Note 7-1 | 125 | ||
| Positive voltage on signal pins with respect to ground | 6 | V | Note 7-2 | 125 | |||
| Negative voltage on signal pins with respect to ground | -0.5 | V | Note 7-3 | 125 | |||
| Positive voltage on XTAL1/CLKIN with respect to ground | 4.6 | V | 125 | ||||
| Positive voltage on XTAL2 with respect to ground | 2.5 | V | 125 | ||||
| Storage temperature | -65 | 150 | oC | 125 | |||
| HBM ESD performance | -5 | 5 | kV | HBM | 125 | ||
| Ambient operating temperature in still air, commercial version | TA | 0 | 70 | oC | Commercial version, Note 7-4 | 125 | |
| Ambient operating temperature in still air, industrial version | TA | -40 | 85 | oC | Industrial version, Note 7-4 | 125 | |
| Supply voltage VDDVARIO operating | VDDVARIO | 1.62 | 3.6 | V | 125 | ||
| Supply voltage VDD33REG, VDD33A operating | 3 | 3.3 | 3.6 | V | +3.3V +/-300mV | 125 | |
| Low input level, VIS type input buffer | VILI | -0.3 | V | VDDVARIO=3.3V +/-300mV | 129 | ||
| High input level, VIS type input buffer | VIHI | 5.5 | V | VDDVARIO=3.3V +/-300mV | 129 | ||
| Negative-going threshold, VIS type input buffer | VILT | 1.01 | 1.18 | 1.35 | V | Schmitt Trigger, VDDVARIO=3.3V +/-300mV | 129 |
| Positive-going threshold, VIS type input buffer | VIHT | 1.4 | 1.61 | 1.81 | V | Schmitt Trigger, VDDVARIO=3.3V +/-300mV | 129 |
| Schmitt trigger hysteresis (VIHT - VILT) | VHYS | 350 | 423 | 492 | mV | VDDVARIO=3.3V +/-300mV | 129 |
| Input leakage | IIH | -10 | 10 | uA | VIN = VSS or VDDVARIO; Note 7-9 | 129 | |
| Input leakage, total for device | IIH | 120 | uA | VIN = 5.5V; Note 7-9, Note 7-10 | 129 | ||
| Low input level, ICLK input buffer | VILCK | -0.3 | 0.5 | V | 129 | ||
| High input level, ICLK input buffer | VIHCK | 1.4 | 3.6 | V | 129 | ||
| Low output level, VO12 type buffer | VOL | 0.4 | V | IOL = 12mA | 129 | ||
| Low output level, VOD12 type buffer | VOL | 0.4 | V | IOL = 12mA | 129 | ||
| Low output level, VOD8 type buffer | VOL | 0.4 | V | IOL = 8mA | 129 | ||
| Low output level, VO8 type buffer | VOL | 0.4 | V | IOL = 8mA | 129 | ||
| Peak differential output voltage high | VPPH | 950 | 1050 | mVpk | Note 7-11 | 132 | |
| Peak differential output voltage low | VPPL | -950 | -1050 | mVpk | Note 7-11; values as printed (MIN -950, MAX -1050) | 132 | |
| Signal amplitude symmetry | VSS | 98 | 102 | % | Note 7-11 | 132 | |
| Signal rise and fall time | TRF | 3 | 5 | nS | Note 7-11 | 132 | |
| Rise and fall time symmetry | TRFS | 0.5 | nS | Note 7-11 | 132 | ||
| Duty cycle distortion | DCD | 35 | 50 | 65 | % | Note 7-12 | 132 |
| Overshoot and undershoot | VOS | -5 | % | 132 | |||
| Transmitter peak differential output voltage | VOUT | 2.2 | 2.5 | 2.8 | V | Note 7-14 | 132 |
| Receiver differential squelch threshold | VDS | 300 | 420 | 585 | mV | 132 | |
| Frequency tolerance at 25oC | Ftol | -50 | 50 | PPM | @25oC; Note 7-15 | 133 | |
| Frequency stability over temperature | Ftemp | -50 | 50 | PPM | Note 7-15 | 133 | |
| Total allowable PPM budget | -50 | 50 | PPM | Note 7-17 | 133 | ||
| Equivalent series resistance | R1 | 50 | Ohm | 133 | |||
| Drive level | PW | 300 | uW | 133 | |||
| Power supply current VDDVARIO maximum | 12 | mA | VDDVARIO=3.3V +300mV; supply voltage 3.6V | 128 | |||
| +3.3V regulator supply current VDD33REG maximum | 85 | mA | Supply voltage 3.6V; VDDVARIO=3.3V +300mV | 128 | |||
| +3.3V analog supply current VDD33A maximum | 48 | mA | Supply voltage 3.6V; VDDVARIO=3.3V +300mV | 128 | |||
| Power supply turn on time | tpon | 50 | ms | Table 6-9 | 122 | ||
| Power supply turn off time | tpoff | 500 | ms | Table 6-9 | 122 | ||
| Crystal frequency | Ffund | 25 | MHz | Fundamental mode | 133 | ||
| Shunt capacitance | CO | 7 | pF | Crystal | 133 | ||
| Load capacitance | CL | 20 | pF | Crystal | 133 | ||
| XTAL1/CLKIN pin capacitance | 3 | pF | Note 7-20 | 133 | |||
| XTAL2 pin capacitance | 3 | pF | Note 7-20 | 133 |
CAD (KiCad official)
- Symbol:
LAN9221-ABZJ - Footprint:
Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm - 3D model: QFN-56(8x8) (KiCad packages3D, STEP)
- 3D model files:
lan9221-abzj-etched.step/lan9221-abzj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lan9221-abzj.step/lan9221-abzj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (141 pp, sha256
e55ed0f7c6ba0abd, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LAN9221-ABZJ
**Microchip Tech** · Ethernet ICs · QFN-56(8x8)
LAN9221-ABZJ from Microchip Tech, in a QFN-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD33REG | power_in | +3.3V power supply for the internal +1.8V regulator. |
| 2 | VDD18CORE | power_out | +1.8V from the internal core regulator; must be tied to pin 37, needs a 0.01uF decoupling capacitor plus a 4.7uF bulk capacitor (<2 Ohm ESR), and must not supply other external devices. |
| 3 | GPIO0/nLED1 | bidirectional | General purpose I/O data (push-pull, open-drain or input via GPIO_CFG) multiplexed with nLED1 open-drain speed indicator, driven low at 100Mb operation. |
| 4 | GPIO1/nLED2 | bidirectional | General purpose I/O data multiplexed with nLED2 open-drain link and activity indicator, driven low on valid link and pulsed high for 80mS on activity. |
| 5 | GPIO2/nLED3 | bidirectional | General purpose I/O data multiplexed with nLED3 open-drain full-duplex indicator, driven low in full-duplex mode. |
| 6 | A7 | input | Host address input bit 7, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored for A[7:3] when FIFO_SEL is high). |
| 7 | A6 | input | Host address input bit 6, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 8 | A5 | input | Host address input bit 5, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 9 | A4 | input | Host address input bit 4, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 10 | A3 | input | Host address input bit 3, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high). |
| 11 | A2 | input | Host address input bit 2, used with A[7:1] to select internal CSRs and TX/RX FIFOs. |
| 12 | A1 | input | Host address input bit 1, used with A[7:1] to select internal CSRs and TX/RX FIFOs. |
| 13 | FIFO_SEL | input | When driven high all accesses are to the RX or TX Data FIFOs and the A[7:3] address inputs are ignored. |
| 14 | TEST | input | Reserved for internal test; has a 50uA typical internal pull-down, must be grounded or pulled low when VDDVARIO is below 3.0V, and may float at 3.3V. |
| 15 | nRD | input | Active-low read strobe indicating a read cycle. |
| 16 | nWR | input | Active-low write strobe indicating a write cycle; qualified with nCS it also wakes the device from a reduced power state. |
| 17 | nCS | input | Active-low chip select qualifying read and write operations; qualified with nWR it also wakes the device from a reduced power state. |
| 18 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 19 | D15 | bidirectional | Host bi-directional data bit 15. |
| 20 | D14 | bidirectional | Host bi-directional data bit 14. |
| 21 | D13 | bidirectional | Host bi-directional data bit 13. |
| 22 | D12 | bidirectional | Host bi-directional data bit 12. |
| 23 | D11 | bidirectional | Host bi-directional data bit 11. |
| 24 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 25 | D10 | bidirectional | Host bi-directional data bit 10. |
| 26 | D9 | bidirectional | Host bi-directional data bit 9. |
| 27 | D8 | bidirectional | Host bi-directional data bit 8. |
| 28 | D7 | bidirectional | Host bi-directional data bit 7. |
| 29 | D6 | bidirectional | Host bi-directional data bit 6. |
| 30 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 31 | D5 | bidirectional | Host bi-directional data bit 5. |
| 32 | D4 | bidirectional | Host bi-directional data bit 4. |
| 33 | D3 | bidirectional | Host bi-directional data bit 3. |
| 34 | D2 | bidirectional | Host bi-directional data bit 2. |
| 35 | D1 | bidirectional | Host bi-directional data bit 1. |
| 36 | D0 | bidirectional | Host bi-directional data bit 0. |
| 37 | VDD18CORE | power_out | +1.8V from the internal core regulator; must be tied to pin 2, needs a 0.01uF decoupling capacitor, and must not supply other external devices. |
| 38 | EEDIO/GPO3 | bidirectional | Serial EEPROM data I/O (optional) or general purpose output 3 / TX_EN / TX_CLK monitor on the internal MII; cannot function as a general-purpose input. |
| 39 | EECS | output | Serial EEPROM chip select. |
| 40 | EECLK/GPO4 | output | Serial EEPROM clock or general purpose output 4 / RX_DV / RX_CLK monitor; has internal pull-up, must not be pulled or driven low, must be left unconnected if the EEPROM is unused, and needs an external pull-up below 3.0V VDDVARIO. |
| 41 | PME | output | Wakeup indicator asserted on a detected wake event, with programmable polarity and buffer type (push-pull or open-drain). |
| 42 | nRESET | input | Active-low reset input for all logic and registers, with weak internal pull-up; must be pulled high externally or driven when VDDVARIO is below 3.0V. |
| 43 | IRQ | output | Programmable interrupt request with programmable polarity, source and buffer type (push-pull or open-drain). |
| 44 | TPO- | output | Ethernet transmit negative output (normal); becomes receive negative input when reversed by HP Auto-MDIX. |
| 45 | TPO+ | output | Ethernet transmit positive output (normal); becomes receive positive input when reversed by HP Auto-MDIX. |
| 46 | VDD33A | power_in | +3.3V analog power supply. |
| 47 | TPI- | input | Ethernet receive negative input (normal); becomes transmit negative output when reversed by HP Auto-MDIX. |
| 48 | TPI+ | input | Ethernet receive positive input (normal); becomes transmit positive input/output when reversed by HP Auto-MDIX. |
| 49 | VDD33A | power_in | +3.3V analog power supply. |
| 50 | EXRES | passive | PHY external bias resistor pin; must be connected to ground through a 12.4K ohm 1% resistor. |
| 51 | VDD33A | power_in | +3.3V analog power supply. |
| 52 | AMDIX_EN | input | Auto-MDIX enable with internal pull-up: pull high or leave unconnected to enable, pull low to disable; needs an external resistor below 3.0V VDDVARIO. |
| 53 | VDD18A | power_in | +1.8V analog power supply; must be connected externally to VDD18CORE. |
| 54 | XTAL2 | output | External 25MHz crystal output; leave unconnected when XTAL1/CLKIN is driven by a single-ended oscillator. |
| 55 | XTAL1/CLKIN | input | External 25MHz crystal input, or single-ended TTL oscillator input (CLKIN). |
| 56 | VDDVARIO | power_in | Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2). |
| 57 | VSS | power_in | Common ground exposed pad on bottom of package; must be connected to ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-56(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 57 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDVARIO, VDD33REG, VDD33A absolute maximum | | 0 | | 3.6 | V | Note 7-1 | 125 |
| Positive voltage on signal pins with respect to ground | | | | 6 | V | Note 7-2 | 125 |
| Negative voltage on signal pins with respect to ground | | -0.5 | | | V | Note 7-3 | 125 |
| Positive voltage on XTAL1/CLKIN with respect to ground | | | | 4.6 | V | | 125 |
| Positive voltage on XTAL2 with respect to ground | | | | 2.5 | V | | 125 |
| Storage temperature | | -65 | | 150 | oC | | 125 |
| HBM ESD performance | | -5 | | 5 | kV | HBM | 125 |
| Ambient operating temperature in still air, commercial version | TA | 0 | | 70 | oC | Commercial version, Note 7-4 | 125 |
| Ambient operating temperature in still air, industrial version | TA | -40 | | 85 | oC | Industrial version, Note 7-4 | 125 |
| Supply voltage VDDVARIO operating | VDDVARIO | 1.62 | | 3.6 | V | | 125 |
| Supply voltage VDD33REG, VDD33A operating | | 3 | 3.3 | 3.6 | V | +3.3V +/-300mV | 125 |
| Low input level, VIS type input buffer | VILI | -0.3 | | | V | VDDVARIO=3.3V +/-300mV | 129 |
| High input level, VIS type input buffer | VIHI | | | 5.5 | V | VDDVARIO=3.3V +/-300mV | 129 |
| Negative-going threshold, VIS type input buffer | VILT | 1.01 | 1.18 | 1.35 | V | Schmitt Trigger, VDDVARIO=3.3V +/-300mV | 129 |
| Positive-going threshold, VIS type input buffer | VIHT | 1.4 | 1.61 | 1.81 | V | Schmitt Trigger, VDDVARIO=3.3V +/-300mV | 129 |
| Schmitt trigger hysteresis (VIHT - VILT) | VHYS | 350 | 423 | 492 | mV | VDDVARIO=3.3V +/-300mV | 129 |
| Input leakage | IIH | -10 | | 10 | uA | VIN = VSS or VDDVARIO; Note 7-9 | 129 |
| Input leakage, total for device | IIH | | | 120 | uA | VIN = 5.5V; Note 7-9, Note 7-10 | 129 |
| Low input level, ICLK input buffer | VILCK | -0.3 | | 0.5 | V | | 129 |
| High input level, ICLK input buffer | VIHCK | 1.4 | | 3.6 | V | | 129 |
| Low output level, VO12 type buffer | VOL | | | 0.4 | V | IOL = 12mA | 129 |
| Low output level, VOD12 type buffer | VOL | | | 0.4 | V | IOL = 12mA | 129 |
| Low output level, VOD8 type buffer | VOL | | | 0.4 | V | IOL = 8mA | 129 |
| Low output level, VO8 type buffer | VOL | | | 0.4 | V | IOL = 8mA | 129 |
| Peak differential output voltage high | VPPH | 950 | | 1050 | mVpk | Note 7-11 | 132 |
| Peak differential output voltage low | VPPL | -950 | | -1050 | mVpk | Note 7-11; values as printed (MIN -950, MAX -1050) | 132 |
| Signal amplitude symmetry | VSS | 98 | | 102 | % | Note 7-11 | 132 |
| Signal rise and fall time | TRF | 3 | | 5 | nS | Note 7-11 | 132 |
| Rise and fall time symmetry | TRFS | | | 0.5 | nS | Note 7-11 | 132 |
| Duty cycle distortion | DCD | 35 | 50 | 65 | % | Note 7-12 | 132 |
| Overshoot and undershoot | VOS | | | -5 | % | | 132 |
| Transmitter peak differential output voltage | VOUT | 2.2 | 2.5 | 2.8 | V | Note 7-14 | 132 |
| Receiver differential squelch threshold | VDS | 300 | 420 | 585 | mV | | 132 |
| Frequency tolerance at 25oC | Ftol | -50 | | 50 | PPM | @25oC; Note 7-15 | 133 |
| Frequency stability over temperature | Ftemp | -50 | | 50 | PPM | Note 7-15 | 133 |
| Total allowable PPM budget | | -50 | | 50 | PPM | Note 7-17 | 133 |
| Equivalent series resistance | R1 | | | 50 | Ohm | | 133 |
| Drive level | PW | 300 | | | uW | | 133 |
| Power supply current VDDVARIO maximum | | | | 12 | mA | VDDVARIO=3.3V +300mV; supply voltage 3.6V | 128 |
| +3.3V regulator supply current VDD33REG maximum | | | | 85 | mA | Supply voltage 3.6V; VDDVARIO=3.3V +300mV | 128 |
| +3.3V analog supply current VDD33A maximum | | | | 48 | mA | Supply voltage 3.6V; VDDVARIO=3.3V +300mV | 128 |
| Power supply turn on time | tpon | | | 50 | ms | Table 6-9 | 122 |
| Power supply turn off time | tpoff | | | 500 | ms | Table 6-9 | 122 |
| Crystal frequency | Ffund | | 25 | | MHz | Fundamental mode | 133 |
| Shunt capacitance | CO | | 7 | | pF | Crystal | 133 |
| Load capacitance | CL | | 20 | | pF | Crystal | 133 |
| XTAL1/CLKIN pin capacitance | | | 3 | | pF | Note 7-20 | 133 |
| XTAL2 pin capacitance | | | 3 | | pF | Note 7-20 | 133 |
## CAD (KiCad official)
- Symbol: `LAN9221-ABZJ`
- Footprint: `Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm`
- 3D model: QFN-56(8x8) (KiCad packages3D, STEP)
- 3D model files: `lan9221-abzj-etched.step` / `lan9221-abzj-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lan9221-abzj.step` / `lan9221-abzj.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/lan9221-abzj-datasheet.pdf) (141 pp, sha256 `e55ed0f7c6ba0abd`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lan9221-abzj-datasheet.pdf)