Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LAN9221-ABZJ

Microchip Tech · Ethernet ICs · QFN-56(8x8)

LAN9221-ABZJ from Microchip Tech, in a QFN-56(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD33REG power_in +3.3V power supply for the internal +1.8V regulator.
2 VDD18CORE power_out +1.8V from the internal core regulator; must be tied to pin 37, needs a 0.01uF decoupling capacitor plus a 4.7uF bulk capacitor (<2 Ohm ESR), and must not supply other external devices.
3 GPIO0/nLED1 bidirectional General purpose I/O data (push-pull, open-drain or input via GPIO_CFG) multiplexed with nLED1 open-drain speed indicator, driven low at 100Mb operation.
4 GPIO1/nLED2 bidirectional General purpose I/O data multiplexed with nLED2 open-drain link and activity indicator, driven low on valid link and pulsed high for 80mS on activity.
5 GPIO2/nLED3 bidirectional General purpose I/O data multiplexed with nLED3 open-drain full-duplex indicator, driven low in full-duplex mode.
6 A7 input Host address input bit 7, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored for A[7:3] when FIFO_SEL is high).
7 A6 input Host address input bit 6, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high).
8 A5 input Host address input bit 5, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high).
9 A4 input Host address input bit 4, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high).
10 A3 input Host address input bit 3, used with A[7:1] to select internal CSRs and TX/RX FIFOs (ignored when FIFO_SEL is high).
11 A2 input Host address input bit 2, used with A[7:1] to select internal CSRs and TX/RX FIFOs.
12 A1 input Host address input bit 1, used with A[7:1] to select internal CSRs and TX/RX FIFOs.
13 FIFO_SEL input When driven high all accesses are to the RX or TX Data FIFOs and the A[7:3] address inputs are ignored.
14 TEST input Reserved for internal test; has a 50uA typical internal pull-down, must be grounded or pulled low when VDDVARIO is below 3.0V, and may float at 3.3V.
15 nRD input Active-low read strobe indicating a read cycle.
16 nWR input Active-low write strobe indicating a write cycle; qualified with nCS it also wakes the device from a reduced power state.
17 nCS input Active-low chip select qualifying read and write operations; qualified with nWR it also wakes the device from a reduced power state.
18 VDDVARIO power_in Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2).
19 D15 bidirectional Host bi-directional data bit 15.
20 D14 bidirectional Host bi-directional data bit 14.
21 D13 bidirectional Host bi-directional data bit 13.
22 D12 bidirectional Host bi-directional data bit 12.
23 D11 bidirectional Host bi-directional data bit 11.
24 VDDVARIO power_in Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2).
25 D10 bidirectional Host bi-directional data bit 10.
26 D9 bidirectional Host bi-directional data bit 9.
27 D8 bidirectional Host bi-directional data bit 8.
28 D7 bidirectional Host bi-directional data bit 7.
29 D6 bidirectional Host bi-directional data bit 6.
30 VDDVARIO power_in Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2).
31 D5 bidirectional Host bi-directional data bit 5.
32 D4 bidirectional Host bi-directional data bit 4.
33 D3 bidirectional Host bi-directional data bit 3.
34 D2 bidirectional Host bi-directional data bit 2.
35 D1 bidirectional Host bi-directional data bit 1.
36 D0 bidirectional Host bi-directional data bit 0.
37 VDD18CORE power_out +1.8V from the internal core regulator; must be tied to pin 2, needs a 0.01uF decoupling capacitor, and must not supply other external devices.
38 EEDIO/GPO3 bidirectional Serial EEPROM data I/O (optional) or general purpose output 3 / TX_EN / TX_CLK monitor on the internal MII; cannot function as a general-purpose input.
39 EECS output Serial EEPROM chip select.
40 EECLK/GPO4 output Serial EEPROM clock or general purpose output 4 / RX_DV / RX_CLK monitor; has internal pull-up, must not be pulled or driven low, must be left unconnected if the EEPROM is unused, and needs an external pull-up below 3.0V VDDVARIO.
41 PME output Wakeup indicator asserted on a detected wake event, with programmable polarity and buffer type (push-pull or open-drain).
42 nRESET input Active-low reset input for all logic and registers, with weak internal pull-up; must be pulled high externally or driven when VDDVARIO is below 3.0V.
43 IRQ output Programmable interrupt request with programmable polarity, source and buffer type (push-pull or open-drain).
44 TPO- output Ethernet transmit negative output (normal); becomes receive negative input when reversed by HP Auto-MDIX.
45 TPO+ output Ethernet transmit positive output (normal); becomes receive positive input when reversed by HP Auto-MDIX.
46 VDD33A power_in +3.3V analog power supply.
47 TPI- input Ethernet receive negative input (normal); becomes transmit negative output when reversed by HP Auto-MDIX.
48 TPI+ input Ethernet receive positive input (normal); becomes transmit positive input/output when reversed by HP Auto-MDIX.
49 VDD33A power_in +3.3V analog power supply.
50 EXRES passive PHY external bias resistor pin; must be connected to ground through a 12.4K ohm 1% resistor.
51 VDD33A power_in +3.3V analog power supply.
52 AMDIX_EN input Auto-MDIX enable with internal pull-up: pull high or leave unconnected to enable, pull low to disable; needs an external resistor below 3.0V VDDVARIO.
53 VDD18A power_in +1.8V analog power supply; must be connected externally to VDD18CORE.
54 XTAL2 output External 25MHz crystal output; leave unconnected when XTAL1/CLKIN is driven by a single-ended oscillator.
55 XTAL1/CLKIN input External 25MHz crystal input, or single-ended TTL oscillator input (CLKIN).
56 VDDVARIO power_in Variable voltage I/O logic power supply (1.8V to 3.3V range per Section 7.2).
57 VSS power_in Common ground exposed pad on bottom of package; must be connected to ground.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-56(8x8)
Category Communication Interface Chip/UART/485/232
Pins 57

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDDVARIO, VDD33REG, VDD33A absolute maximum 0 3.6 V Note 7-1 125
Positive voltage on signal pins with respect to ground 6 V Note 7-2 125
Negative voltage on signal pins with respect to ground -0.5 V Note 7-3 125
Positive voltage on XTAL1/CLKIN with respect to ground 4.6 V 125
Positive voltage on XTAL2 with respect to ground 2.5 V 125
Storage temperature -65 150 oC 125
HBM ESD performance -5 5 kV HBM 125
Ambient operating temperature in still air, commercial version TA 0 70 oC Commercial version, Note 7-4 125
Ambient operating temperature in still air, industrial version TA -40 85 oC Industrial version, Note 7-4 125
Supply voltage VDDVARIO operating VDDVARIO 1.62 3.6 V 125
Supply voltage VDD33REG, VDD33A operating 3 3.3 3.6 V +3.3V +/-300mV 125
Low input level, VIS type input buffer VILI -0.3 V VDDVARIO=3.3V +/-300mV 129
High input level, VIS type input buffer VIHI 5.5 V VDDVARIO=3.3V +/-300mV 129
Negative-going threshold, VIS type input buffer VILT 1.01 1.18 1.35 V Schmitt Trigger, VDDVARIO=3.3V +/-300mV 129
Positive-going threshold, VIS type input buffer VIHT 1.4 1.61 1.81 V Schmitt Trigger, VDDVARIO=3.3V +/-300mV 129
Schmitt trigger hysteresis (VIHT - VILT) VHYS 350 423 492 mV VDDVARIO=3.3V +/-300mV 129
Input leakage IIH -10 10 uA VIN = VSS or VDDVARIO; Note 7-9 129
Input leakage, total for device IIH 120 uA VIN = 5.5V; Note 7-9, Note 7-10 129
Low input level, ICLK input buffer VILCK -0.3 0.5 V 129
High input level, ICLK input buffer VIHCK 1.4 3.6 V 129
Low output level, VO12 type buffer VOL 0.4 V IOL = 12mA 129
Low output level, VOD12 type buffer VOL 0.4 V IOL = 12mA 129
Low output level, VOD8 type buffer VOL 0.4 V IOL = 8mA 129
Low output level, VO8 type buffer VOL 0.4 V IOL = 8mA 129
Peak differential output voltage high VPPH 950 1050 mVpk Note 7-11 132
Peak differential output voltage low VPPL -950 -1050 mVpk Note 7-11; values as printed (MIN -950, MAX -1050) 132
Signal amplitude symmetry VSS 98 102 % Note 7-11 132
Signal rise and fall time TRF 3 5 nS Note 7-11 132
Rise and fall time symmetry TRFS 0.5 nS Note 7-11 132
Duty cycle distortion DCD 35 50 65 % Note 7-12 132
Overshoot and undershoot VOS -5 % 132
Transmitter peak differential output voltage VOUT 2.2 2.5 2.8 V Note 7-14 132
Receiver differential squelch threshold VDS 300 420 585 mV 132
Frequency tolerance at 25oC Ftol -50 50 PPM @25oC; Note 7-15 133
Frequency stability over temperature Ftemp -50 50 PPM Note 7-15 133
Total allowable PPM budget -50 50 PPM Note 7-17 133
Equivalent series resistance R1 50 Ohm 133
Drive level PW 300 uW 133
Power supply current VDDVARIO maximum 12 mA VDDVARIO=3.3V +300mV; supply voltage 3.6V 128
+3.3V regulator supply current VDD33REG maximum 85 mA Supply voltage 3.6V; VDDVARIO=3.3V +300mV 128
+3.3V analog supply current VDD33A maximum 48 mA Supply voltage 3.6V; VDDVARIO=3.3V +300mV 128
Power supply turn on time tpon 50 ms Table 6-9 122
Power supply turn off time tpoff 500 ms Table 6-9 122
Crystal frequency Ffund 25 MHz Fundamental mode 133
Shunt capacitance CO 7 pF Crystal 133
Load capacitance CL 20 pF Crystal 133
XTAL1/CLKIN pin capacitance 3 pF Note 7-20 133
XTAL2 pin capacitance 3 pF Note 7-20 133

CAD (KiCad official)

  • Symbol: LAN9221-ABZJ
  • Footprint: Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm
  • 3D model: QFN-56(8x8) (KiCad packages3D, STEP)
  • 3D model files: lan9221-abzj-etched.step / lan9221-abzj-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lan9221-abzj.step / lan9221-abzj.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (141 pp, sha256 e55ed0f7c6ba0abd, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF