main
Ray
Publish 0.1.0
4e30731
LAN91C111-NU
Microchip Tech · Ethernet Transceivers · TQFP-128(14x14)
LAN91C111-NU from Microchip Tech, in a TQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | +3.3V power supply pin. |
| 2 | nCSOUT | output | Chip select output for external registers, active on accesses to the lower eight addresses when bank 7 is selected. |
| 3 | IOS0 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 4 | IOS1 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 5 | IOS2 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 6 | ENEEP | input | Enables serial EEPROM accesses when high or open and must be grounded if no EEPROM is connected. |
| 7 | EEDO | output | Serial EEPROM data output connected to the DI input of the EEPROM. |
| 8 | EEDI | input | Serial EEPROM data input connected to the DO output of the EEPROM, with an internal pulldown. |
| 9 | EESK | output | EEPROM clock output used to shift data in and out of the serial EEPROM. |
| 10 | EECS | output | Serial EEPROM chip select output used for selection and command framing. |
| 11 | AVDD | power_in | +3.3V analog power supply pin. |
| 12 | RBIAS | passive | An external resistor between this pin and GND sets the output current for the TP transmit outputs. |
| 13 | AGND | power_in | Analog ground pin. |
| 14 | TPO+ | output | Twisted pair transmit output, positive. |
| 15 | TPO- | output | Twisted pair transmit output, negative. |
| 16 | AVDD | power_in | +3.3V analog power supply pin. |
| 17 | TPI+ | bidirectional | Twisted pair receive input, positive. |
| 18 | TPI- | bidirectional | Twisted pair receive input, negative. |
| 19 | AGND | power_in | Analog ground pin. |
| 20 | nLNK | input | General-purpose input conveying link status (EPHSR bit 14), with an internal pullup. |
| 21 | LBK | output | Output that is active when the LOOP bit (TCR bit 1) is set. |
| 22 | nLEDA | output | PHY LED output, open drain with 24mA sink. |
| 23 | nLEDB | output | PHY LED output, open drain with 24mA sink. |
| 24 | GND | power_in | Ground pin. |
| 25 | MDI | input | MII management data input, with an internal pulldown. |
| 26 | MDO | output | MII management data output. |
| 27 | MCLK | output | MII management clock output. |
| 28 | nCNTRL | output | General purpose control output pin (O12 buffer). |
| 29 | INTR0 | output | Active high interrupt output used to interrupt the host on a status event. |
| 30 | RESET | input | When asserted high for at least 100ns, performs an internal MAC and PHY reset. |
| 31 | nRD | input | Read strobe input used in asynchronous bus interfaces. |
| 32 | nWR | input | Write strobe input used in asynchronous bus interfaces. |
| 33 | VDD | power_in | +3.3V power supply pin. |
| 34 | nDATACS | input | Data path chip select; when low the data path can be accessed for 32-bit bursts regardless of AEN and A1-A15. |
| 35 | nCYCLE | input | Active low signal controlling EISA burst mode synchronous bus cycles. |
| 36 | W/nR | input | Defines the direction of synchronous cycles: write when high, read when low. |
| 37 | nADS | input | Rising edge latches A1-A15 and AEN for systems requiring address latching. |
| 38 | ARDY | output | Open drain output used to extend asynchronous bus accesses (OD16, 16mA sink). |
| 39 | GND | power_in | Ground pin. |
| 40 | nVLBUS | input | When low, the synchronous bus interface is configured for VL Bus accesses; it has an internal pullup. |
| 41 | AEN | input | Address qualifier; address decoding is enabled only when AEN is low. |
| 42 | LCLK | input | Local bus clock for synchronous buses, with a maximum frequency of 50 MHz. |
| 43 | nSRDY | output | Synchronous ready output used to extend accesses when nVLBUS=0, synchronous to LCLK. |
| 44 | VDD | power_in | +3.3V power supply pin. |
| 45 | nLDEV | output | Active low when AEN is low and A4-A15 decode to the programmed base address (O16 buffer). |
| 46 | nRDYRTN | input | Input used to complete synchronous read cycles, sampled on falling LCLK edges in EISA burst mode. |
| 47 | X25OUT | output | 25 MHz clock output to an external PHY. |
| 48 | D31 | bidirectional | Bit 31 of the 32-bit data bus, with weak internal pullup; 12mA source and 24mA sink. |
| 49 | D30 | bidirectional | Bit 30 of the 32-bit data bus, with weak internal pullup. |
| 50 | D29 | bidirectional | Bit 29 of the 32-bit data bus, with weak internal pullup. |
| 51 | D28 | bidirectional | Bit 28 of the 32-bit data bus, with weak internal pullup. |
| 52 | GND | power_in | Ground pin. |
| 53 | D27 | bidirectional | Bit 27 of the 32-bit data bus, with weak internal pullup. |
| 54 | D26 | bidirectional | Bit 26 of the 32-bit data bus, with weak internal pullup. |
| 55 | D25 | bidirectional | Bit 25 of the 32-bit data bus, with weak internal pullup. |
| 56 | D24 | bidirectional | Bit 24 of the 32-bit data bus, with weak internal pullup. |
| 57 | GND | power_in | Ground pin. |
| 58 | D23 | bidirectional | Bit 23 of the 32-bit data bus, with weak internal pullup. |
| 59 | D22 | bidirectional | Bit 22 of the 32-bit data bus, with weak internal pullup. |
| 60 | D21 | bidirectional | Bit 21 of the 32-bit data bus, with weak internal pullup. |
| 61 | D20 | bidirectional | Bit 20 of the 32-bit data bus, with weak internal pullup. |
| 62 | VDD | power_in | +3.3V power supply pin. |
| 63 | D19 | bidirectional | Bit 19 of the 32-bit data bus, with weak internal pullup. |
| 64 | D18 | bidirectional | Bit 18 of the 32-bit data bus, with weak internal pullup. |
| 65 | D17 | bidirectional | Bit 17 of the 32-bit data bus, with weak internal pullup. |
| 66 | D16 | bidirectional | Bit 16 of the 32-bit data bus, with weak internal pullup. |
| 67 | GND | power_in | Ground pin. |
| 68 | D15 | bidirectional | Bit 15 of the 32-bit data bus, with weak internal pullup; only D0-D15 are used in 16-bit systems. |
| 69 | D14 | bidirectional | Bit 14 of the 32-bit data bus, with weak internal pullup. |
| 70 | D13 | bidirectional | Bit 13 of the 32-bit data bus, with weak internal pullup. |
| 71 | D12 | bidirectional | Bit 12 of the 32-bit data bus, with weak internal pullup. |
| 72 | GND | power_in | Ground pin. |
| 73 | D11 | bidirectional | Bit 11 of the 32-bit data bus, with weak internal pullup. |
| 74 | D10 | bidirectional | Bit 10 of the 32-bit data bus, with weak internal pullup. |
| 75 | D9 | bidirectional | Bit 9 of the 32-bit data bus, with weak internal pullup. |
| 76 | D8 | bidirectional | Bit 8 of the 32-bit data bus, with weak internal pullup. |
| 77 | VDD | power_in | +3.3V power supply pin. |
| 78 | A1 | input | Address input used for internal register selection (5V tolerant). |
| 79 | A2 | input | Address input used for internal register selection (5V tolerant). |
| 80 | A3 | input | Address input used for internal register selection (5V tolerant). |
| 81 | A4 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 82 | A5 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 83 | A6 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 84 | A7 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 85 | A8 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 86 | A9 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 87 | A10 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 88 | A11 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 89 | A12 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 90 | A13 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 91 | A14 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 92 | A15 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 93 | GND | power_in | Ground pin. |
| 94 | nBE0 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 95 | nBE1 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 96 | nBE2 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 97 | nBE3 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 98 | VDD | power_in | +3.3V power supply pin. |
| 99 | D7 | bidirectional | Bit 7 of the 32-bit data bus, with weak internal pullup. |
| 100 | D6 | bidirectional | Bit 6 of the 32-bit data bus, with weak internal pullup. |
| 101 | D5 | bidirectional | Bit 5 of the 32-bit data bus, with weak internal pullup. |
| 102 | D4 | bidirectional | Bit 4 of the 32-bit data bus, with weak internal pullup. |
| 103 | GND | power_in | Ground pin. |
| 104 | D3 | bidirectional | Bit 3 of the 32-bit data bus, with weak internal pullup. |
| 105 | D2 | bidirectional | Bit 2 of the 32-bit data bus, with weak internal pullup. |
| 106 | D1 | bidirectional | Bit 1 of the 32-bit data bus, with weak internal pullup. |
| 107 | D0 | bidirectional | Bit 0 of the 32-bit data bus, with weak internal pullup. |
| 108 | GND | power_in | Ground pin. |
| 109 | TX25 | input | Transmit clock input from MII at nibble rate (25MHz for 100Mbps, 2.5MHz for 10Mbps), with an internal pullup. |
| 110 | VDD | power_in | +3.3V power supply pin. |
| 111 | TXEN100 | output | Output to MII PHY that envelopes 100 Mbps transmission (O12 buffer). |
| 112 | COL100 | input | Collision detect input from MII PHY, with an internal pulldown. |
| 113 | TXD3 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 114 | TXD2 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 115 | TXD1 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 116 | TXD0 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 117 | GND | power_in | Ground pin. |
| 118 | RX25 | input | Receive clock input from MII PHY at nibble rate (25MHz for 100Mbps, 2.5MHz for 10Mbps), with an internal pullup. |
| 119 | CRS100 | input | Carrier sense input from MII PHY used for deferral and backoff, with an internal pulldown. |
| 120 | VDD | power_in | +3.3V power supply pin. |
| 121 | RXD3 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 122 | RXD2 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 123 | RXD1 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 124 | RXD0 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 125 | RX_DV | input | Receive data valid input from MII PHY used for receive data framing, with an internal pulldown. |
| 126 | RX_ER | input | Receive error input from PHY that causes the received packet to be discarded, with an internal pulldown. |
| 127 | XTAL1 | input | Connected to a 25 MHz crystal; if a TTL clock is supplied instead, it is connected here with XTAL2 left open. |
| 128 | XTAL2 | output | Output of the internal crystal amplifier, connected to a 25 MHz crystal across XTAL1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-128(14x14) |
| Category | Communication Interface Chip |
| Pins | 128 |
CAD (KiCad official)
- Symbol:
LAN91C111-NU - Footprint:
Package_QFP:TQFP-128_14x14mm_P0.4mm - 3D model: TQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files:
lan91c111-nu-etched.step/lan91c111-nu-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lan91c111-nu.step/lan91c111-nu.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (125 pp, sha256
fcbbe864a0f58951, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LAN91C111-NU
**Microchip Tech** · Ethernet Transceivers · TQFP-128(14x14)
LAN91C111-NU from Microchip Tech, in a TQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | +3.3V power supply pin. |
| 2 | nCSOUT | output | Chip select output for external registers, active on accesses to the lower eight addresses when bank 7 is selected. |
| 3 | IOS0 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 4 | IOS1 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 5 | IOS2 | input | External switch input that selects between predefined EEPROM configurations, with an internal pullup. |
| 6 | ENEEP | input | Enables serial EEPROM accesses when high or open and must be grounded if no EEPROM is connected. |
| 7 | EEDO | output | Serial EEPROM data output connected to the DI input of the EEPROM. |
| 8 | EEDI | input | Serial EEPROM data input connected to the DO output of the EEPROM, with an internal pulldown. |
| 9 | EESK | output | EEPROM clock output used to shift data in and out of the serial EEPROM. |
| 10 | EECS | output | Serial EEPROM chip select output used for selection and command framing. |
| 11 | AVDD | power_in | +3.3V analog power supply pin. |
| 12 | RBIAS | passive | An external resistor between this pin and GND sets the output current for the TP transmit outputs. |
| 13 | AGND | power_in | Analog ground pin. |
| 14 | TPO+ | output | Twisted pair transmit output, positive. |
| 15 | TPO- | output | Twisted pair transmit output, negative. |
| 16 | AVDD | power_in | +3.3V analog power supply pin. |
| 17 | TPI+ | bidirectional | Twisted pair receive input, positive. |
| 18 | TPI- | bidirectional | Twisted pair receive input, negative. |
| 19 | AGND | power_in | Analog ground pin. |
| 20 | nLNK | input | General-purpose input conveying link status (EPHSR bit 14), with an internal pullup. |
| 21 | LBK | output | Output that is active when the LOOP bit (TCR bit 1) is set. |
| 22 | nLEDA | output | PHY LED output, open drain with 24mA sink. |
| 23 | nLEDB | output | PHY LED output, open drain with 24mA sink. |
| 24 | GND | power_in | Ground pin. |
| 25 | MDI | input | MII management data input, with an internal pulldown. |
| 26 | MDO | output | MII management data output. |
| 27 | MCLK | output | MII management clock output. |
| 28 | nCNTRL | output | General purpose control output pin (O12 buffer). |
| 29 | INTR0 | output | Active high interrupt output used to interrupt the host on a status event. |
| 30 | RESET | input | When asserted high for at least 100ns, performs an internal MAC and PHY reset. |
| 31 | nRD | input | Read strobe input used in asynchronous bus interfaces. |
| 32 | nWR | input | Write strobe input used in asynchronous bus interfaces. |
| 33 | VDD | power_in | +3.3V power supply pin. |
| 34 | nDATACS | input | Data path chip select; when low the data path can be accessed for 32-bit bursts regardless of AEN and A1-A15. |
| 35 | nCYCLE | input | Active low signal controlling EISA burst mode synchronous bus cycles. |
| 36 | W/nR | input | Defines the direction of synchronous cycles: write when high, read when low. |
| 37 | nADS | input | Rising edge latches A1-A15 and AEN for systems requiring address latching. |
| 38 | ARDY | output | Open drain output used to extend asynchronous bus accesses (OD16, 16mA sink). |
| 39 | GND | power_in | Ground pin. |
| 40 | nVLBUS | input | When low, the synchronous bus interface is configured for VL Bus accesses; it has an internal pullup. |
| 41 | AEN | input | Address qualifier; address decoding is enabled only when AEN is low. |
| 42 | LCLK | input | Local bus clock for synchronous buses, with a maximum frequency of 50 MHz. |
| 43 | nSRDY | output | Synchronous ready output used to extend accesses when nVLBUS=0, synchronous to LCLK. |
| 44 | VDD | power_in | +3.3V power supply pin. |
| 45 | nLDEV | output | Active low when AEN is low and A4-A15 decode to the programmed base address (O16 buffer). |
| 46 | nRDYRTN | input | Input used to complete synchronous read cycles, sampled on falling LCLK edges in EISA burst mode. |
| 47 | X25OUT | output | 25 MHz clock output to an external PHY. |
| 48 | D31 | bidirectional | Bit 31 of the 32-bit data bus, with weak internal pullup; 12mA source and 24mA sink. |
| 49 | D30 | bidirectional | Bit 30 of the 32-bit data bus, with weak internal pullup. |
| 50 | D29 | bidirectional | Bit 29 of the 32-bit data bus, with weak internal pullup. |
| 51 | D28 | bidirectional | Bit 28 of the 32-bit data bus, with weak internal pullup. |
| 52 | GND | power_in | Ground pin. |
| 53 | D27 | bidirectional | Bit 27 of the 32-bit data bus, with weak internal pullup. |
| 54 | D26 | bidirectional | Bit 26 of the 32-bit data bus, with weak internal pullup. |
| 55 | D25 | bidirectional | Bit 25 of the 32-bit data bus, with weak internal pullup. |
| 56 | D24 | bidirectional | Bit 24 of the 32-bit data bus, with weak internal pullup. |
| 57 | GND | power_in | Ground pin. |
| 58 | D23 | bidirectional | Bit 23 of the 32-bit data bus, with weak internal pullup. |
| 59 | D22 | bidirectional | Bit 22 of the 32-bit data bus, with weak internal pullup. |
| 60 | D21 | bidirectional | Bit 21 of the 32-bit data bus, with weak internal pullup. |
| 61 | D20 | bidirectional | Bit 20 of the 32-bit data bus, with weak internal pullup. |
| 62 | VDD | power_in | +3.3V power supply pin. |
| 63 | D19 | bidirectional | Bit 19 of the 32-bit data bus, with weak internal pullup. |
| 64 | D18 | bidirectional | Bit 18 of the 32-bit data bus, with weak internal pullup. |
| 65 | D17 | bidirectional | Bit 17 of the 32-bit data bus, with weak internal pullup. |
| 66 | D16 | bidirectional | Bit 16 of the 32-bit data bus, with weak internal pullup. |
| 67 | GND | power_in | Ground pin. |
| 68 | D15 | bidirectional | Bit 15 of the 32-bit data bus, with weak internal pullup; only D0-D15 are used in 16-bit systems. |
| 69 | D14 | bidirectional | Bit 14 of the 32-bit data bus, with weak internal pullup. |
| 70 | D13 | bidirectional | Bit 13 of the 32-bit data bus, with weak internal pullup. |
| 71 | D12 | bidirectional | Bit 12 of the 32-bit data bus, with weak internal pullup. |
| 72 | GND | power_in | Ground pin. |
| 73 | D11 | bidirectional | Bit 11 of the 32-bit data bus, with weak internal pullup. |
| 74 | D10 | bidirectional | Bit 10 of the 32-bit data bus, with weak internal pullup. |
| 75 | D9 | bidirectional | Bit 9 of the 32-bit data bus, with weak internal pullup. |
| 76 | D8 | bidirectional | Bit 8 of the 32-bit data bus, with weak internal pullup. |
| 77 | VDD | power_in | +3.3V power supply pin. |
| 78 | A1 | input | Address input used for internal register selection (5V tolerant). |
| 79 | A2 | input | Address input used for internal register selection (5V tolerant). |
| 80 | A3 | input | Address input used for internal register selection (5V tolerant). |
| 81 | A4 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 82 | A5 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 83 | A6 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 84 | A7 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 85 | A8 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 86 | A9 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 87 | A10 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 88 | A11 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 89 | A12 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 90 | A13 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 91 | A14 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 92 | A15 | input | Address input decoded to determine access to the registers (5V tolerant). |
| 93 | GND | power_in | Ground pin. |
| 94 | nBE0 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 95 | nBE1 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 96 | nBE2 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 97 | nBE3 | input | Byte enable input that determines access width and the register(s) accessed; ignored when nDATACS is low. |
| 98 | VDD | power_in | +3.3V power supply pin. |
| 99 | D7 | bidirectional | Bit 7 of the 32-bit data bus, with weak internal pullup. |
| 100 | D6 | bidirectional | Bit 6 of the 32-bit data bus, with weak internal pullup. |
| 101 | D5 | bidirectional | Bit 5 of the 32-bit data bus, with weak internal pullup. |
| 102 | D4 | bidirectional | Bit 4 of the 32-bit data bus, with weak internal pullup. |
| 103 | GND | power_in | Ground pin. |
| 104 | D3 | bidirectional | Bit 3 of the 32-bit data bus, with weak internal pullup. |
| 105 | D2 | bidirectional | Bit 2 of the 32-bit data bus, with weak internal pullup. |
| 106 | D1 | bidirectional | Bit 1 of the 32-bit data bus, with weak internal pullup. |
| 107 | D0 | bidirectional | Bit 0 of the 32-bit data bus, with weak internal pullup. |
| 108 | GND | power_in | Ground pin. |
| 109 | TX25 | input | Transmit clock input from MII at nibble rate (25MHz for 100Mbps, 2.5MHz for 10Mbps), with an internal pullup. |
| 110 | VDD | power_in | +3.3V power supply pin. |
| 111 | TXEN100 | output | Output to MII PHY that envelopes 100 Mbps transmission (O12 buffer). |
| 112 | COL100 | input | Collision detect input from MII PHY, with an internal pulldown. |
| 113 | TXD3 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 114 | TXD2 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 115 | TXD1 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 116 | TXD0 | output | Transmit data nibble output to MII PHY (O12 buffer). |
| 117 | GND | power_in | Ground pin. |
| 118 | RX25 | input | Receive clock input from MII PHY at nibble rate (25MHz for 100Mbps, 2.5MHz for 10Mbps), with an internal pullup. |
| 119 | CRS100 | input | Carrier sense input from MII PHY used for deferral and backoff, with an internal pulldown. |
| 120 | VDD | power_in | +3.3V power supply pin. |
| 121 | RXD3 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 122 | RXD2 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 123 | RXD1 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 124 | RXD0 | input | Received data nibble input from MII PHY, with an internal pullup. |
| 125 | RX_DV | input | Receive data valid input from MII PHY used for receive data framing, with an internal pulldown. |
| 126 | RX_ER | input | Receive error input from PHY that causes the received packet to be discarded, with an internal pulldown. |
| 127 | XTAL1 | input | Connected to a 25 MHz crystal; if a TTL clock is supplied instead, it is connected here with XTAL2 left open. |
| 128 | XTAL2 | output | Output of the internal crystal amplifier, connected to a 25 MHz crystal across XTAL1. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-128(14x14) |
| Category | Communication Interface Chip |
| Pins | 128 |
## CAD (KiCad official)
- Symbol: `LAN91C111-NU`
- Footprint: `Package_QFP:TQFP-128_14x14mm_P0.4mm`
- 3D model: TQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files: `lan91c111-nu-etched.step` / `lan91c111-nu-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lan91c111-nu.step` / `lan91c111-nu.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/lan91c111-nu-datasheet.pdf) (125 pp, sha256 `fcbbe864a0f58951`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lan91c111-nu-datasheet.pdf)