by adom
Microchip LAN7800 — single-chip SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet controller with integrated USB device controller + PHY, Ethernet MAC, and Gigabit PHY. QFN-48 in 7x7 mm (Y9X) and 6x6 mm (VSX).
master
John Lauer
Variants -HV-SB-RR (16 vias + 296-ball User.9 layer + roundrect pads, one footprint) and -LE (baseline copy with its ow…
7bfa24d
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219
{
"part": "LAN7800",
"package": "QFN-48 7x7mm",
"source": "adom/lan7800",
"generator": "adom-footprint 1.0.22 (heatsink / solderballs verbs)",
"deviceset": "one Fusion deviceset; each variant is a device bound to its own STEP so Change Package swaps footprint + 3D together",
"variants": [
{
"suffix": "",
"device": "baseline",
"kicad_mod": "lan7800-qfn48-7x7-y9x.kicad_mod",
"footprintName": "QFN-48 7x7mm",
"step": "QFN-48_7x7mm.step",
"changed": "nothing; the page footprint as-is (49 SMD pads)",
"stepAliases": [
"LAN7800.step",
"LAN7800.step"
]
},
{
"suffix": "-HV",
"device": "heatsink vias",
"kicad_mod": "lan7800-qfn48-7x7-y9x-HV.kicad_mod",
"footprintName": "QFN-48 7x7mm-HV",
"step": "QFN-48_7x7mm-HV.step",
"changed": "+16 thru_hole pads under pad 49 (1.2 mm pitch, 0.3 mm drill, 0.6 mm OD, 0.45 mm inset), on copper + mask layers only (*.Cu *.Mask); nothing on a drawing layer",
"viaPadNumber": "49",
"viaPadNumberNote": "KiCad: pads sharing a number share the net, so the vias are on the EP net with no symbol change and DRC is clean. EAGLE needs unique pad names: adom-lbr should emit them as [email protected]@16 (EAGLE's own multi-pad convention) and connect all 17 to the EP pin.",
"vias": [
{
"x": -1.8,
"y": -1.8
},
{
"x": -0.6,
"y": -1.8
},
{
"x": 0.6,
"y": -1.8
},
{
"x": 1.8,
"y": -1.8
},
{
"x": -1.8,
"y": -0.6
},
{
"x": -0.6,
"y": -0.6
},
{
"x": 0.6,
"y": -0.6
},
{
"x": 1.8,
"y": -0.6
},
{
"x": -1.8,
"y": 0.6
},
{
"x": -0.6,
"y": 0.6
},
{
"x": 0.6,
"y": 0.6
},
{
"x": 1.8,
"y": 0.6
},
{
"x": -1.8,
"y": 1.8
},
{
"x": -0.6,
"y": 1.8
},
{
"x": 0.6,
"y": 1.8
},
{
"x": 1.8,
"y": 1.8
}
],
"via": {
"annularDiameter": 0.6,
"drill": 0.3,
"net": "same as pad 49",
"plated": true,
"ringWidth": 0.15
},
"pitch": 1.2,
"insetFromPadEdge": 0.44999999999999996,
"stepAliases": [
"LAN7800.heatsink-vias.step",
"LAN7800-HV.step"
]
},
{
"suffix": "-SB",
"device": "solder balls",
"kicad_mod": "lan7800-qfn48-7x7-y9x-SB.kicad_mod",
"footprintName": "QFN-48 7x7mm-SB",
"step": "QFN-48_7x7mm-SB.step",
"changed": "+296 filled fp_circle \u00d80.30 mm on KiCad layer User.9 (Adom.SolderBalls), one per 300um jet-paste ball at 0.25 mm pitch; copper unchanged",
"ballLayer": {
"kicad": "User.9",
"name": "Adom.SolderBalls",
"eagleLayer": 101,
"note": "a .kicad_mod cannot carry a layer NAME (that lives in the board's layer table), so the layer is User.9 in the file and this manifest is the sidecar that names it; adom-lbr maps User.9 -> 101 Adom.SolderBalls",
"hiddenByDefault": true
},
"ball": {
"alloy": "63Sn/37Pb, Indium 12.8HF flux, type 6 powder, 80% metal",
"diameter": 0.3,
"pitch": 0.25,
"shape": "hemisphere, flat face on the pad"
},
"count": 296,
"ballsJson": "lan7800-qfn48-7x7-y9x-SB.solder-balls.json",
"stepAliases": [
"LAN7800.solder-balls.step",
"LAN7800-SB.step"
]
},
{
"suffix": "-RR",
"device": "rounded pads",
"kicad_mod": "lan7800-qfn48-7x7-y9x-RR.kicad_mod",
"footprintName": "QFN-48 7x7mm-RR",
"step": "QFN-48_7x7mm-RR.step",
"stepAliases": [
"LAN7800-RR.step",
"QFN-48_7x7mm.step (same chip body as baseline)"
],
"changed": "every SMD pad shape -> KiCad roundrect: signal pads roundrect_rratio 0.25 (the KiCad/IPC default; EAGLE/Fusion roundness 50 = percent of the pad's smaller side), exposed pad 49 roundrect_rratio 0.1 (roundness 20); copper positions and sizes unchanged. Note: the baseline's signal pads were `oval` (semicircular ends), so -RR is LESS rounded at the ends than baseline, not more; it matches Altium's default rounded-rectangle style.",
"padShape": {
"signal": {
"shape": "roundrect",
"rratio": 0.25,
"eagleRoundness": 50
},
"exposedPad": {
"shape": "roundrect",
"rratio": 0.1,
"eagleRoundness": 20
}
}
},
{
"suffix": "-LE",
"device": "laser-etched model",
"kicad_mod": "lan7800-qfn48-7x7-y9x-LE.kicad_mod",
"footprintName": "QFN-48 7x7mm-LE",
"step": "QFN-48_7x7mm-LE.step",
"stepAliases": [
"LAN7800-LE.step"
],
"changed": "footprint identical to baseline (own package name so adom-lbr gets a distinct package); the 3D model carries the laser-etched part number (step2glb)"
},
{
"suffix": "-HV-SB-RR",
"device": "heatsink vias + solder balls + rounded pads",
"kicad_mod": "lan7800-qfn48-7x7-y9x-HV-SB-RR.kicad_mod",
"footprintName": "QFN-48 7x7mm-HV-SB-RR",
"step": "QFN-48_7x7mm-HV-SB-RR.step",
"stepAliases": [
"LAN7800-HV-SB-RR.step"
],
"changed": "= -RR pads (roundrect rratio 0.25, EP 0.1) + the 16 heatsink vias as thru_hole pads on 49 + the 296-ball Adom.SolderBalls layer on User.9; the 3D model is the CHIP-ONLY laser-etched body (no via or ball solids: Fusion generates vias from the pads on the board, and nobody wants balls rendered)",
"vias": 16,
"balls": 296,
"padShape": {
"signal": {
"shape": "roundrect",
"rratio": 0.25,
"eagleRoundness": 50
},
"exposedPad": {
"shape": "roundrect",
"rratio": 0.1,
"eagleRoundness": 20
}
},
"ballLayer": {
"kicad": "User.9",
"name": "Adom.SolderBalls",
"eagleLayer": 101,
"hiddenByDefault": true
}
}
],
"notes": [
"-SB carries no vias, but its balls still keep 0.55 mm clear of the STANDARD via positions (the keep-out is derived from the exposed-pad geometry, not from vias present in the file), so -SB and the layered file both have 296 balls and a board can gain the vias later without moving paste. The vias+balls combination is lan7800-qfn48-7x7-y9x.layers.kicad_mod if a fourth device is ever wanted.",
"Re-running `adom-footprint heatsink` / `solderballs` on a variant is idempotent."
],
"stepPairing": "Fusion bridge binds a STEP to a PACKAGE by name: stem == package name (case-insensitive after normalisation, spaces -> _), then deviceset+device (LAN7800-HV), then deviceset. Use `step`; `stepAliases` are the older descriptive names and do not pair on their own.",
"pin1": {
"corner": "top-left",
"order": "ccw",
"description": "Datasheet DS00001992 Figure 3-1 (top view): pin 1 top-left; pins 1..12 run DOWN the left edge, 13..24 along the bottom left-to-right, 25..36 UP the right edge, 37..48 along the top right-to-left. Pad 1 at KiCad (-3.5, -2.75); silk pin-1 dot at (-3.5, -3.5).",
"verified": "2026-08-30 against the datasheet figure and the 6x6 VSX footprint on this page (same orientation); the STEP's pin-1 dimple (top-left) now matches with model rotate 0 0 0",
"history": "Before 2026-08-30 the y9x footprint was rotated 90 degrees (pad 1 bottom-left, 1..12 along the bottom); fixed by rotating pads (size w/h swapped) and silk/courtyard/comment geometry with (x, y) -> (-y, x) in KiCad's Y-down frame; text and the STEP binding were left as they were."
},
"baselineFixes": [
"2026-08-30: F.CrtYd grown from the 7x7 body (\u00b13.5, which cut through the pads) to \u00b14.25 mm = pads (\u00b14.0) + 0.25 mm IPC nominal; lint courtyard_too_small cleared.",
"2026-08-30: F.Fab body outline added: 7x7 fp_poly with a 1 mm pin-1 chamfer at the top-left corner."
]
}