main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs l6564tdtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers l6564tdtr: viewers · Ray
l6564tdtr-etched.fit.json l6564tdtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6564tdtr-etched.glb l6564tdtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6564tdtr-etched.step l6564tdtr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
l6564tdtr.glb Publish 0.1.0 · Ray
l6564tdtr.kicad_mod Publish 0.1.0 · Ray
l6564tdtr.kicad_sym Publish 0.1.0 · Ray
l6564tdtr.lbr Publish 0.1.0 · Ray
l6564tdtr.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json l6564tdtr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md l6564tdtr: laser-etched CAD + chip hero (factory 2.0.0 backfill) · Ray

L6564TDTR

STMicroelectronics · AC-DC Controllers and Regulators · SSOP-10-150mil

L6564TDTR from STMicroelectronics, in a SSOP-10-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 INV input Inverting input of the internal error amplifier. Output voltage of the PFC pre-regulator is fed into this pin through a resistor divider. High-impedance input; internal reference is 2.5 V (typ).
2 COMP output Error amplifier output. A compensation network between this pin and INV sets the voltage loop stability. Gate driver is inhibited (burst-mode) when VCOMP falls below ~2.4 V.
3 MULT input Main input to the multiplier. Connected to the rectified mains voltage via a resistor divider to provide the sinusoidal reference for the current loop and to derive RMS mains information. Linear range 0-3 V; internal clamp ~9.5 V.
4 CS input PWM comparator current-sense input. MOSFET current is sensed through a shunt and applied here; compared to an internal reference to terminate the on-time. A second 1.7 V comparator detects abnormal currents (inductor saturation) and triggers a safety hiccup.
5 VFF input Voltage feedforward input to the multiplier for the 1/V^2 function. A capacitor and parallel resistor (100 kΩ min to 2 MΩ max) from this pin to GND complete the peak-holding circuit that derives RMS mains information. Also feeds the brownout comparator: <0.8 V shuts down the IC (not latched); restart above 0.88 V.
6 PFC_OK input PFC pre-regulator output-voltage monitoring / disable input. Senses PFC output through a resistor divider. Above 2.5 V the IC stops switching (OVP); if simultaneously VINV<1.66 V a feedback failure is latched off. Below 0.23 V the IC is shut down; restart above 0.27 V (usable as remote on/off).
7 ZCD input Boost-inductor demagnetization sensing input for transition-mode operation. A negative-going edge triggers MOSFET turn-on. Max ZCD current -10 mA (source) / 10 mA (sink).
8 GND power_in Ground. Common current return for both the signal part of the IC and the gate driver.
9 GD output Gate driver output. Totem-pole stage capable of 600 mA source / 800 mA sink for MOSFET or IGBT drive. High-level clamped at ~12 V to prevent excessive gate voltages; active pull-down during UVLO.
10 Vcc power_in Supply voltage for both the signal part of the IC and the gate driver. Operating range 10.3-22.5 V after turn-on; turn-on threshold ~12 V, turn-off ~9.5 V, internal Zener clamp ~25 V. A ~0.1 µF bypass to GND is recommended.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SSOP-10-150mil
Category PMIC
Pins 10

Ordering variants

Same part, different packaging or reel option.

  • L6564TDTR

CAD (KiCad official)

  • Symbol: L6564TDTR
  • Footprint: Package_SO:SSOP-10_3.9x4.9mm_P1.00mm
  • 3D model: SSOP-10-150mil (KiCad packages3D, STEP)
  • 3D model files: l6564tdtr-etched.step / l6564tdtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l6564tdtr.step / l6564tdtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (33 pp, sha256 d9194e06a2a0df36, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF