main
Ray
Publish 0.1.0
544a865
L6562ATDTR
STMicroelectronics · AC-DC Controllers & Regulators · SO-8
L6562ATDTR from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INV | input | Inverting input of the error amplifier, fed from the output divider, which doubles as a not-latched ON/OFF control where a voltage below 0.2 V shuts the IC down and it restarts above 0.45 V. |
| 2 | COMP | output | Output of the error amplifier, with a compensation network between this pin and INV to ensure voltage loop stability, high power factor and low THD, clamped between 2.25 V (lower) and 5.7 V (upper) typical. |
| 3 | MULT | input | Main input to the multiplier, connected to the rectified mains voltage via a resistor divider to provide the sinusoidal current reference, with a linear operation range of 0 to 3 V. |
| 4 | CS | input | Input to the PWM comparator that senses the MOSFET current through a resistor and sets turn-off, with 200 ns leading-edge blanking for improved noise immunity. |
| 5 | ZCD | input | Boost inductor demagnetization sensing input for transition-mode operation, where a negative-going edge triggers MOSFET turn-on, with a zero current detector maximum current of ±10 mA. |
| 6 | GND | power_in | Ground, serving as the current return for both the signal part of the IC and the gate driver. |
| 7 | GD | output | Gate driver totem-pole output able to drive power MOSFETs and IGBTs with 600 mA peak source and 800 mA peak sink current, with the high-level voltage clamped at about 12 V. |
| 8 | Vcc | power_in | Supply voltage of both the signal part of the IC and the gate driver, with the operating range given as 10.5 V to 22.5 V and the upper limit extended to 22 V minimum. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating range | VCC | 10.5 | 22.5 | V | After turn-on | 6 | |
| Turn-on threshold | VccOn | 11.7 | 12.5 | 13.3 | V | 6 | |
| Turn-off threshold | VccOff | 9.5 | 10 | 10.5 | V | 6 | |
| Hysteresis | Hys | 2.2 | 2.8 | V | 6 | ||
| Zener voltage | VZ | 22.5 | 25 | 28 | V | ICC = 20 mA | 6 |
| Start-up current | Istart-up | 30 | 60 | µA | Before turn-on, VCC = 11 V | 6 | |
| Quiescent current | Iq | 2.5 | 3.9 | mA | After turn-on | 6 | |
| Operating supply current | ICC | 3.5 | 5.5 | mA | @ 70 kHz | 6 | |
| Quiescent current during OVP | Iq | 1.7 | 2.2 | mA | During OVP (either static or dynamic) or VINV ≤ 150 mV | 6 | |
| Input bias current | IMULT | -1 | µA | VMULT = 0 to 4 V | 6 | ||
| Linear operation range | VMULT | 0 | 3 | V | 6 | ||
| Output max slope | 1 | 1.1 | V/V | VMULT = 0 to 1 V, VCOMP = Upper clamp | 6 | ||
| Gain | K | 0.32 | 0.38 | 0.47 | V | VMULT = 1 V, VCOMP = 4 V | 6 |
| Voltage feedback input threshold | VINV | 2.475 | 2.5 | 2.525 | V | TJ = 25 °C | 6 |
| Voltage feedback input threshold | VINV | 2.44 | 2.545 | V | 10.5 V < VCC < 22.5 V | 6 | |
| Line regulation | 2 | 5 | mV | VCC = 10.5 V to 22.5 V | 6 | ||
| Voltage gain | Gv | 60 | 80 | dB | Open loop | 6 | |
| Gain-bandwidth product | GB | 1 | MHz | 6 | |||
| Source current | ICOMP | -2 | -3.5 | -5 | mA | VCOMP = 4 V, VINV = 2.4 V | 6 |
| Sink current | ICOMP | 2.5 | 4.5 | mA | VCOMP = 4 V, VINV = 2.6 V | 6 | |
| Upper clamp voltage | VCOMP | 5.1 | 5.7 | 6 | V | ISOURCE = 0.5 mA | 6 |
| Lower clamp voltage | VCOMP | 2.1 | 2.25 | 2.4 | V | ISINK = 0.5 mA | 6 |
| Disable threshold | VINVdis | 150 | 200 | 250 | mV | 6 | |
| Restart threshold | VINVen | 380 | 450 | 520 | mV | 6 | |
| Dynamic OVP triggering current | IOVP | 19.5 | 27 | 30.5 | µA | 7 | |
| Hysteresis | Hys | 20 | µA | 7 | |||
| Static OVP threshold | 2.1 | 2.25 | 2.4 | V | 7 | ||
| Input bias current | ICS | -1 | µA | VCS = 0 | 7 | ||
| Leading edge blanking | tLEB | 100 | 200 | 300 | ns | 7 | |
| Delay to output | td(H-L) | 175 | ns | 7 | |||
| Current sense clamp | VCS | 1 | 1.08 | 1.16 | V | VCOMP = Upper clamp, Vmult = 1.5 V | 7 |
| Current sense offset | Vcsoffset | 25 | mV | VMULT = 0 | 7 | ||
| Current sense offset | Vcsoffset | 5 | mV | VMULT = 2.5 V | 7 | ||
| Upper clamp voltage | VZCDH | 5 | 5.7 | 6.5 | V | IZCD = 2.5 mA | 7 |
| Lower clamp voltage | VZCDL | -0.5 | 0 | 0.5 | V | IZCD = -2.5 mA | 7 |
| Arming voltage | VZCDA | 1.4 | V | Positive-going edge | 7 | ||
| Triggering voltage | VZCDT | 0.7 | V | Negative-going edge | 7 | ||
| Input bias current | IZCDb | 2 | µA | VZCD = 1 to 4.5 V | 7 | ||
| Source current capability | IZCDsrc | -1.5 | mA | 7 | |||
| Sink current capability | IZCDsnk | 1.5 | mA | 7 | |||
| Start timer period | tSTART | 75 | 190 | 300 | µs | 7 | |
| Output low voltage | VOL | 0.6 | 1.2 | V | Isink = 100 mA | 7 | |
| Output high voltage | VOH | 9.5 | 10.3 | V | Isource = 5 mA | 7 | |
| Peak source current | Isrcpk | -0.6 | A | 7 | |||
| Peak sink current | Isnkpk | 0.8 | A | 7 | |||
| Voltage fall time | tf | 30 | 70 | ns | 7 | ||
| Voltage rise time | tr | 60 | 130 | ns | 7 | ||
| Output clamp voltage | VOclamp | 10 | 12 | 15 | V | Isource = 5 mA; Vcc = 20 V | 7 |
| UVLO saturation | 1.1 | V | Vcc = 0 to VCCon, Isink = 2 mA | 7 | |||
| Max thermal resistance junction-to-ambient (SO8) | RthJA | 150 | °C/W | 5 | |||
| Power dissipation (SO8) | PTOT | 0.65 | W | @ TA = 50 °C | 5 | ||
| Junction temperature operating range | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | TSTG | -55 | 150 | °C | 5 | ||
| Analog inputs and outputs | -0.3 | 8 | V | Pins 1 to 4 | 5 | ||
| Zero current detector max current | IZCD | -10 | 10 | mA | 5 |
CAD (KiCad official)
- Symbol:
L6562ATDTR - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
l6562atdtr-etched.step/l6562atdtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l6562atdtr.step/l6562atdtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (25 pp, sha256
0a6466f9da6298f1, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# L6562ATDTR
**STMicroelectronics** · AC-DC Controllers & Regulators · SO-8
L6562ATDTR from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INV | input | Inverting input of the error amplifier, fed from the output divider, which doubles as a not-latched ON/OFF control where a voltage below 0.2 V shuts the IC down and it restarts above 0.45 V. |
| 2 | COMP | output | Output of the error amplifier, with a compensation network between this pin and INV to ensure voltage loop stability, high power factor and low THD, clamped between 2.25 V (lower) and 5.7 V (upper) typical. |
| 3 | MULT | input | Main input to the multiplier, connected to the rectified mains voltage via a resistor divider to provide the sinusoidal current reference, with a linear operation range of 0 to 3 V. |
| 4 | CS | input | Input to the PWM comparator that senses the MOSFET current through a resistor and sets turn-off, with 200 ns leading-edge blanking for improved noise immunity. |
| 5 | ZCD | input | Boost inductor demagnetization sensing input for transition-mode operation, where a negative-going edge triggers MOSFET turn-on, with a zero current detector maximum current of ±10 mA. |
| 6 | GND | power_in | Ground, serving as the current return for both the signal part of the IC and the gate driver. |
| 7 | GD | output | Gate driver totem-pole output able to drive power MOSFETs and IGBTs with 600 mA peak source and 800 mA peak sink current, with the high-level voltage clamped at about 12 V. |
| 8 | Vcc | power_in | Supply voltage of both the signal part of the IC and the gate driver, with the operating range given as 10.5 V to 22.5 V and the upper limit extended to 22 V minimum. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating range | VCC | 10.5 | | 22.5 | V | After turn-on | 6 |
| Turn-on threshold | VccOn | 11.7 | 12.5 | 13.3 | V | | 6 |
| Turn-off threshold | VccOff | 9.5 | 10 | 10.5 | V | | 6 |
| Hysteresis | Hys | 2.2 | | 2.8 | V | | 6 |
| Zener voltage | VZ | 22.5 | 25 | 28 | V | ICC = 20 mA | 6 |
| Start-up current | Istart-up | | 30 | 60 | µA | Before turn-on, VCC = 11 V | 6 |
| Quiescent current | Iq | | 2.5 | 3.9 | mA | After turn-on | 6 |
| Operating supply current | ICC | | 3.5 | 5.5 | mA | @ 70 kHz | 6 |
| Quiescent current during OVP | Iq | | 1.7 | 2.2 | mA | During OVP (either static or dynamic) or VINV ≤ 150 mV | 6 |
| Input bias current | IMULT | -1 | | | µA | VMULT = 0 to 4 V | 6 |
| Linear operation range | VMULT | 0 | | 3 | V | | 6 |
| Output max slope | | | 1 | 1.1 | V/V | VMULT = 0 to 1 V, VCOMP = Upper clamp | 6 |
| Gain | K | 0.32 | 0.38 | 0.47 | V | VMULT = 1 V, VCOMP = 4 V | 6 |
| Voltage feedback input threshold | VINV | 2.475 | 2.5 | 2.525 | V | TJ = 25 °C | 6 |
| Voltage feedback input threshold | VINV | 2.44 | | 2.545 | V | 10.5 V < VCC < 22.5 V | 6 |
| Line regulation | | | 2 | 5 | mV | VCC = 10.5 V to 22.5 V | 6 |
| Voltage gain | Gv | 60 | | 80 | dB | Open loop | 6 |
| Gain-bandwidth product | GB | | 1 | | MHz | | 6 |
| Source current | ICOMP | -2 | -3.5 | -5 | mA | VCOMP = 4 V, VINV = 2.4 V | 6 |
| Sink current | ICOMP | 2.5 | | 4.5 | mA | VCOMP = 4 V, VINV = 2.6 V | 6 |
| Upper clamp voltage | VCOMP | 5.1 | 5.7 | 6 | V | ISOURCE = 0.5 mA | 6 |
| Lower clamp voltage | VCOMP | 2.1 | 2.25 | 2.4 | V | ISINK = 0.5 mA | 6 |
| Disable threshold | VINVdis | 150 | 200 | 250 | mV | | 6 |
| Restart threshold | VINVen | 380 | 450 | 520 | mV | | 6 |
| Dynamic OVP triggering current | IOVP | 19.5 | 27 | 30.5 | µA | | 7 |
| Hysteresis | Hys | | 20 | | µA | | 7 |
| Static OVP threshold | | 2.1 | 2.25 | 2.4 | V | | 7 |
| Input bias current | ICS | -1 | | | µA | VCS = 0 | 7 |
| Leading edge blanking | tLEB | 100 | 200 | 300 | ns | | 7 |
| Delay to output | td(H-L) | | 175 | | ns | | 7 |
| Current sense clamp | VCS | 1 | 1.08 | 1.16 | V | VCOMP = Upper clamp, Vmult = 1.5 V | 7 |
| Current sense offset | Vcsoffset | | 25 | | mV | VMULT = 0 | 7 |
| Current sense offset | Vcsoffset | | 5 | | mV | VMULT = 2.5 V | 7 |
| Upper clamp voltage | VZCDH | 5 | 5.7 | 6.5 | V | IZCD = 2.5 mA | 7 |
| Lower clamp voltage | VZCDL | -0.5 | 0 | 0.5 | V | IZCD = -2.5 mA | 7 |
| Arming voltage | VZCDA | | 1.4 | | V | Positive-going edge | 7 |
| Triggering voltage | VZCDT | | 0.7 | | V | Negative-going edge | 7 |
| Input bias current | IZCDb | | 2 | | µA | VZCD = 1 to 4.5 V | 7 |
| Source current capability | IZCDsrc | -1.5 | | | mA | | 7 |
| Sink current capability | IZCDsnk | 1.5 | | | mA | | 7 |
| Start timer period | tSTART | 75 | 190 | 300 | µs | | 7 |
| Output low voltage | VOL | | 0.6 | 1.2 | V | Isink = 100 mA | 7 |
| Output high voltage | VOH | 9.5 | | 10.3 | V | Isource = 5 mA | 7 |
| Peak source current | Isrcpk | -0.6 | | | A | | 7 |
| Peak sink current | Isnkpk | | | 0.8 | A | | 7 |
| Voltage fall time | tf | | 30 | 70 | ns | | 7 |
| Voltage rise time | tr | | 60 | 130 | ns | | 7 |
| Output clamp voltage | VOclamp | 10 | 12 | 15 | V | Isource = 5 mA; Vcc = 20 V | 7 |
| UVLO saturation | | | | 1.1 | V | Vcc = 0 to VCCon, Isink = 2 mA | 7 |
| Max thermal resistance junction-to-ambient (SO8) | RthJA | | | 150 | °C/W | | 5 |
| Power dissipation (SO8) | PTOT | | | 0.65 | W | @ TA = 50 °C | 5 |
| Junction temperature operating range | TJ | -40 | | 150 | °C | | 5 |
| Storage temperature | TSTG | -55 | | 150 | °C | | 5 |
| Analog inputs and outputs | | -0.3 | | 8 | V | Pins 1 to 4 | 5 |
| Zero current detector max current | IZCD | -10 | | 10 | mA | | 5 |
## CAD (KiCad official)
- Symbol: `L6562ATDTR`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `l6562atdtr-etched.step` / `l6562atdtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l6562atdtr.step` / `l6562atdtr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/l6562atdtr.pdf) (25 pp, sha256 `0a6466f9da6298f1`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/l6562atdtr-datasheet.pdf)