main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers l6562atdtr: viewers · Ray
l6562atdtr-etched.glb Publish 0.1.0 · Ray
l6562atdtr-etched.step l6562atdtr: factory component page (tier=mfr) · Ray
l6562atdtr-hero.glb l6562atdtr: hero GLB from the etched model (keeps the MPN mark) · Ray
l6562atdtr-hero.overlay.json Publish 0.1.0 · Ray
l6562atdtr.glb Publish 0.1.0 · Ray
l6562atdtr.kicad_mod Publish 0.1.0 · Ray
l6562atdtr.kicad_sym Publish 0.1.0 · Ray
l6562atdtr.lbr Publish 0.1.0 · Ray
l6562atdtr.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 8 pins · Ray

L6562ATDTR

STMicroelectronics · AC-DC Controllers & Regulators · SO-8

L6562ATDTR from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 INV input Inverting input of the error amplifier, fed from the output divider, which doubles as a not-latched ON/OFF control where a voltage below 0.2 V shuts the IC down and it restarts above 0.45 V.
2 COMP output Output of the error amplifier, with a compensation network between this pin and INV to ensure voltage loop stability, high power factor and low THD, clamped between 2.25 V (lower) and 5.7 V (upper) typical.
3 MULT input Main input to the multiplier, connected to the rectified mains voltage via a resistor divider to provide the sinusoidal current reference, with a linear operation range of 0 to 3 V.
4 CS input Input to the PWM comparator that senses the MOSFET current through a resistor and sets turn-off, with 200 ns leading-edge blanking for improved noise immunity.
5 ZCD input Boost inductor demagnetization sensing input for transition-mode operation, where a negative-going edge triggers MOSFET turn-on, with a zero current detector maximum current of ±10 mA.
6 GND power_in Ground, serving as the current return for both the signal part of the IC and the gate driver.
7 GD output Gate driver totem-pole output able to drive power MOSFETs and IGBTs with 600 mA peak source and 800 mA peak sink current, with the high-level voltage clamped at about 12 V.
8 Vcc power_in Supply voltage of both the signal part of the IC and the gate driver, with the operating range given as 10.5 V to 22.5 V and the upper limit extended to 22 V minimum.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SO-8
Category Power Supply Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating range VCC 10.5 22.5 V After turn-on 6
Turn-on threshold VccOn 11.7 12.5 13.3 V 6
Turn-off threshold VccOff 9.5 10 10.5 V 6
Hysteresis Hys 2.2 2.8 V 6
Zener voltage VZ 22.5 25 28 V ICC = 20 mA 6
Start-up current Istart-up 30 60 µA Before turn-on, VCC = 11 V 6
Quiescent current Iq 2.5 3.9 mA After turn-on 6
Operating supply current ICC 3.5 5.5 mA @ 70 kHz 6
Quiescent current during OVP Iq 1.7 2.2 mA During OVP (either static or dynamic) or VINV ≤ 150 mV 6
Input bias current IMULT -1 µA VMULT = 0 to 4 V 6
Linear operation range VMULT 0 3 V 6
Output max slope 1 1.1 V/V VMULT = 0 to 1 V, VCOMP = Upper clamp 6
Gain K 0.32 0.38 0.47 V VMULT = 1 V, VCOMP = 4 V 6
Voltage feedback input threshold VINV 2.475 2.5 2.525 V TJ = 25 °C 6
Voltage feedback input threshold VINV 2.44 2.545 V 10.5 V < VCC < 22.5 V 6
Line regulation 2 5 mV VCC = 10.5 V to 22.5 V 6
Voltage gain Gv 60 80 dB Open loop 6
Gain-bandwidth product GB 1 MHz 6
Source current ICOMP -2 -3.5 -5 mA VCOMP = 4 V, VINV = 2.4 V 6
Sink current ICOMP 2.5 4.5 mA VCOMP = 4 V, VINV = 2.6 V 6
Upper clamp voltage VCOMP 5.1 5.7 6 V ISOURCE = 0.5 mA 6
Lower clamp voltage VCOMP 2.1 2.25 2.4 V ISINK = 0.5 mA 6
Disable threshold VINVdis 150 200 250 mV 6
Restart threshold VINVen 380 450 520 mV 6
Dynamic OVP triggering current IOVP 19.5 27 30.5 µA 7
Hysteresis Hys 20 µA 7
Static OVP threshold 2.1 2.25 2.4 V 7
Input bias current ICS -1 µA VCS = 0 7
Leading edge blanking tLEB 100 200 300 ns 7
Delay to output td(H-L) 175 ns 7
Current sense clamp VCS 1 1.08 1.16 V VCOMP = Upper clamp, Vmult = 1.5 V 7
Current sense offset Vcsoffset 25 mV VMULT = 0 7
Current sense offset Vcsoffset 5 mV VMULT = 2.5 V 7
Upper clamp voltage VZCDH 5 5.7 6.5 V IZCD = 2.5 mA 7
Lower clamp voltage VZCDL -0.5 0 0.5 V IZCD = -2.5 mA 7
Arming voltage VZCDA 1.4 V Positive-going edge 7
Triggering voltage VZCDT 0.7 V Negative-going edge 7
Input bias current IZCDb 2 µA VZCD = 1 to 4.5 V 7
Source current capability IZCDsrc -1.5 mA 7
Sink current capability IZCDsnk 1.5 mA 7
Start timer period tSTART 75 190 300 µs 7
Output low voltage VOL 0.6 1.2 V Isink = 100 mA 7
Output high voltage VOH 9.5 10.3 V Isource = 5 mA 7
Peak source current Isrcpk -0.6 A 7
Peak sink current Isnkpk 0.8 A 7
Voltage fall time tf 30 70 ns 7
Voltage rise time tr 60 130 ns 7
Output clamp voltage VOclamp 10 12 15 V Isource = 5 mA; Vcc = 20 V 7
UVLO saturation 1.1 V Vcc = 0 to VCCon, Isink = 2 mA 7
Max thermal resistance junction-to-ambient (SO8) RthJA 150 °C/W 5
Power dissipation (SO8) PTOT 0.65 W @ TA = 50 °C 5
Junction temperature operating range TJ -40 150 °C 5
Storage temperature TSTG -55 150 °C 5
Analog inputs and outputs -0.3 8 V Pins 1 to 4 5
Zero current detector max current IZCD -10 10 mA 5

CAD (KiCad official)

  • Symbol: L6562ATDTR
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SO-8 (KiCad packages3D, STEP)
  • 3D model files: l6562atdtr-etched.step / l6562atdtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l6562atdtr.step / l6562atdtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (25 pp, sha256 0a6466f9da6298f1, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF