main
Ray
Publish 0.1.0
3ee162e
L6470H
STMicroelectronics · Stepper Motor Driver · HTSSOP-28
L6470H from STMicroelectronics, in a HTSSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT1A | power_out | Full bridge A output 1. |
| 2 | VSA | power_in | Full bridge A power supply pin; it must be connected to VSB. |
| 3 | STBY\RST | input | Standby and reset pin; LOW logic level resets the logic and puts the device into Standby mode, and if not used it should be connected to VDD. |
| 4 | SW | input | External switch input pin; if not used it should be connected to VDD. |
| 5 | ADCIN | input | Internal analog-to-digital converter input. |
| 6 | VREG | power_out | Internal 3 V voltage regulator output and 3.3 V external logic supply. |
| 7 | OSCIN | input | Oscillator pin 1 to connect an external oscillator or clock source; it should be left floating if unused. |
| 8 | OSCOUT | output | Oscillator pin 2 to connect an external oscillator; when the internal oscillator is used it can supply 2/4/8/16 MHz. |
| 9 | AGND | power_in | Analog ground. |
| 10 | CP | output | Charge pump oscillator output. |
| 11 | VBOOT | power_in | Bootstrap voltage needed for driving the high-side power DMOS of both bridges (A and B). |
| 12 | VSB | power_in | Full bridge B power supply pin; it must be connected to VSA. |
| 13 | PGND | power_in | Power ground pin. |
| 14 | OUT1B | power_out | Full bridge B output 1. |
| 15 | OUT2B | power_out | Full bridge B output 2. |
| 16 | VSB | power_in | Full bridge B power supply pin; it must be connected to VSA. |
| 17 | VDD | power_in | Logic outputs supply voltage (pull-up reference). |
| 18 | SDO | output | Data output pin for the serial interface. |
| 19 | CK | input | Serial interface clock input. |
| 20 | SDI | input | Data input pin for the serial interface. |
| 21 | DGND | power_in | Digital ground. |
| 22 | BUSY\SYNC | output | Open drain output forced low while a command is executed; otherwise it can be configured to generate a synchronization signal. |
| 23 | CS | input | Chip select input pin for the serial interface. |
| 24 | FLAG | output | Open drain status flag output that is pulled to GND when a programmed alarm condition occurs. |
| 25 | STCK | input | Step-clock input. |
| 26 | VSA | power_in | Full bridge A power supply pin; it must be connected to VSB. |
| 27 | PGND | power_in | Power ground pin. |
| 28 | OUT2A | power_out | Full bridge A output 2. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | HTSSOP-28 |
| Category | Motor Driver ICs |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic interface supply voltage | VDD | 5.5 | V | 9 | |||
| Motor supply voltage | VS | 48 | V | VSA = VSB = VS | 9 | ||
| Differential voltage between AGND, PGND and DGND | VGND,diff | -0.3 | 0.3 | V | 9 | ||
| Bootstrap peak voltage | Vboot | 55 | V | 9 | |||
| Internal voltage regulator output pin and logic supply voltage | VREG | 3.6 | V | 9 | |||
| Integrated ADC input voltage range (ADCIN pin) | VADCIN | -0.3 | 3.6 | V | 9 | ||
| OCSIN and OSCOUT pin voltage range | VOSC | -0.3 | 3.6 | V | 9 | ||
| Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins | Vout_diff | 48 | V | VSA = VSB = VS | 9 | ||
| Logic inputs voltage range | VLOGIC | -0.3 | 5.5 | V | 9 | ||
| R.m.s. output current | Iout | 3 | A | 9 | |||
| Pulsed output current | Iout_peak | 7 | A | TPULSE < 1 ms | 9 | ||
| Operating junction temperature | TOP | -40 | 150 | °C | 9 | ||
| Storage temperature range | Ts | -55 | 150 | °C | 9 | ||
| Total power dissipation | Ptot | 5 | W | TA = 25 ºC; HTSSOP28 mounted on EVAL6470H | 9 | ||
| Motor supply voltage | VS | 8 | 45 | V | VSA = VSB = VS | 10 | |
| Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins | Vout_diff | 45 | V | VSA = VSB = VS | 10 | ||
| Logic supply voltage | VREG,in | 3.2 | 3.3 | V | VREG voltage imposed by external source | 10 | |
| Integrated ADC input voltage (ADCIN pin) | VADC | 0 | V | ADCIN pin; upper limit VREG | 10 | ||
| Thermal resistance junction ambient | RthJA | 22 | °C/W | HTSSOP28 mounted on EVAL6470H rev 1.0 board | 10 | ||
| UVLO turn-on threshold | VSthOn | 7.5 | 8.2 | 8.9 | V | 11 | |
| UVLO turn-off threshold | VSthOff | 6.6 | 7.2 | 7.8 | V | 11 | |
| UVLO threshold hysteresis | VSthHyst | 0.7 | 1 | 1.3 | V | 11 | |
| Quiescent motor supply current | Iq | 0.5 | 0.65 | mA | Internal oscillator selected; VREG = 3.3 V ext.; CP floating | 11 | |
| Thermal warning temperature | Tj(WRN) | 130 | °C | 11 | |||
| Thermal shutdown temperature | Tj(SD) | 160 | °C | 11 | |||
| Voltage swing for charge pump oscillator | Vpump | 10 | V | 11 | |||
| Minimum charge pump oscillator frequency | fpump,min | 660 | kHz | 11 | |||
| Maximum charge pump oscillator frequency | fpump,max | 800 | kHz | 11 | |||
| Average boot current | Iboot | 1.1 | 1.4 | mA | fsw,A = fsw,B = 15.6 kHz; POW_SR = '10' | 11 | |
| High-side switch on-resistance | RDS(on) | 0.37 | ohm | Tj = 25 °C, Iout = 3 A | 11 | ||
| High-side switch on-resistance | RDS(on) | 0.51 | ohm | Tj = 125 °C, Iout = 3 A | 11 | ||
| Low-side switch on-resistance | RDS(on) | 0.18 | ohm | Tj = 25 °C, Iout = 3 A | 11 | ||
| Low-side switch on-resistance | RDS(on) | 0.23 | ohm | Tj = 125 °C, Iout = 3 A | 11 | ||
| High-side diode forward ON voltage | VSD,HS | 1 | 1.1 | V | Iout = 1 A | 12 | |
| Low-side diode forward ON voltage | VSD,LS | 1 | 1.1 | V | Iout = 1 A | 12 | |
| High-side diode reverse recovery time | trrHS | 30 | ns | Iout = 1 A | 12 | ||
| Low-side diode reverse recovery time | trrLS | 100 | ns | Iout = 1 A | 12 | ||
| Low logic level input voltage | VIL | 0.8 | V | 12 | |||
| High logic level input voltage | VIH | 2 | V | 12 | |||
| Low logic level output voltage | VOL | 0.3 | V | VDD = 3.3 V, IOL = 4 mA | 13 | ||
| High logic level output voltage | VOH | 2.4 | V | VDD = 3.3 V, IOH = 4 mA | 13 | ||
| High logic level output voltage | VOH | 4.7 | V | VDD = 5 V, IOH = 4 mA | 13 | ||
| CS pull-up and STBY pull-down resistors | RPU/RPD | 335 | 430 | 565 | k | CS = GND; STBY/RST = 5 V | 13 |
| Internal logic supply current | Ilogic | 3.7 | 4.3 | mA | 3.3 V VREG externally supplied, internal oscillator | 13 | |
| Standby mode internal logic supply current | Ilogic,STBY | 2 | 2.5 | µA | 3.3 V VREG externally supplied | 13 | |
| Step-clock input frequency | fSTCK | 2 | MHz | 13 | |||
| Internal oscillator frequency | fosc,i | -3 | 3 | % | Tj = 25 °C, VREG = 3.3 V | 13 | |
| Internal oscillator frequency | fosc,i | 16 | MHz | Tj = 25 °C, VREG = 3.3 V | 13 | ||
| Programmable external oscillator frequency | fosc,e | 8 | 32 | MHz | 13 | ||
| OSCOUT clock source high level voltage | VOSCOUTH | 2.4 | V | Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA | 13 | ||
| OSCOUT clock source low level voltage | VOSCOUTL | 0.3 | V | Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA | 13 | ||
| Maximum SPI clock frequency | fCK,MAX | 5 | MHz | 13 | |||
| SPI clock rise and fall time | trCK/tfCK | 25 | ns | CL = 30 pF | 13 | ||
| SPI clock high and low time | thCK/tlCK | 75 | ns | 13 | |||
| Chip select setup time | tsetCS | 350 | ns | 13 | |||
| Chip select hold time | tholCS | 10 | ns | 13 | |||
| Deselect time | tdisCS | 800 | ns | 13 | |||
| Data input setup time | tsetSDI | 25 | ns | 13 | |||
| Data input hold time | tholSDI | 20 | ns | 13 | |||
| Data output enable time | tenSDO | 38 | ns | 14 | |||
| Data output disable time | tdisSDO | 47 | ns | 14 | |||
| Data output valid time | tvSDO | 57 | ns | 14 | |||
| Data output hold time | tholSDO | 37 | ns | 14 | |||
| SW input pull-up resistance | RPUSW | 60 | 85 | 110 | k | SW = GND | 14 |
| Programmable PWM frequency | fPWM | 2.8 | 62.5 | kHz | fosc = 16 MHz | 14 | |
| Programmable PWM frequency | fPWM | 5.6 | 125 | kHz | fosc = 32 MHz | 14 | |
| PWM resolution | NPWM | 8 | bit | 14 | |||
| Quiescent motor supply current in standby conditions | IqSTBY | 26 | 34 | µA | VS = 8 V | 14 | |
| Quiescent motor supply current in standby conditions | IqSTBY | 30 | 36 | µA | VS = 36 V | 14 | |
| Minimum standby time | tSTBY,min | 10 | s | 14 | |||
| Logic power-on and wake-up time | tlogicwu | 38 | 45 | µs | 14 | ||
| Voltage regulator output voltage | VREG | 2.9 | 3 | 3.2 | V | 14 | |
| Voltage regulator output current | IREG | 40 | mA | 14 | |||
| Voltage regulator output voltage drop | VREG,drop | 50 | mV | IREG = 40 mA | 14 | ||
| Voltage regulator standby output current | IREG,STBY | 10 | mA | 14 | |||
| Analog-to-digital converter resolution | NADC | 5 | bit | 14 |
CAD (KiCad official)
- Symbol:
L6470H - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: HTSSOP-28 (KiCad packages3D, STEP)
- 3D model files:
l6470h-etched.step/l6470h-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l6470h.step/l6470h.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (73 pp, sha256
4b94ab59eec71372, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# L6470H
**STMicroelectronics** · Stepper Motor Driver · HTSSOP-28
L6470H from STMicroelectronics, in a HTSSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT1A | power_out | Full bridge A output 1. |
| 2 | VSA | power_in | Full bridge A power supply pin; it must be connected to VSB. |
| 3 | STBY\RST | input | Standby and reset pin; LOW logic level resets the logic and puts the device into Standby mode, and if not used it should be connected to VDD. |
| 4 | SW | input | External switch input pin; if not used it should be connected to VDD. |
| 5 | ADCIN | input | Internal analog-to-digital converter input. |
| 6 | VREG | power_out | Internal 3 V voltage regulator output and 3.3 V external logic supply. |
| 7 | OSCIN | input | Oscillator pin 1 to connect an external oscillator or clock source; it should be left floating if unused. |
| 8 | OSCOUT | output | Oscillator pin 2 to connect an external oscillator; when the internal oscillator is used it can supply 2/4/8/16 MHz. |
| 9 | AGND | power_in | Analog ground. |
| 10 | CP | output | Charge pump oscillator output. |
| 11 | VBOOT | power_in | Bootstrap voltage needed for driving the high-side power DMOS of both bridges (A and B). |
| 12 | VSB | power_in | Full bridge B power supply pin; it must be connected to VSA. |
| 13 | PGND | power_in | Power ground pin. |
| 14 | OUT1B | power_out | Full bridge B output 1. |
| 15 | OUT2B | power_out | Full bridge B output 2. |
| 16 | VSB | power_in | Full bridge B power supply pin; it must be connected to VSA. |
| 17 | VDD | power_in | Logic outputs supply voltage (pull-up reference). |
| 18 | SDO | output | Data output pin for the serial interface. |
| 19 | CK | input | Serial interface clock input. |
| 20 | SDI | input | Data input pin for the serial interface. |
| 21 | DGND | power_in | Digital ground. |
| 22 | BUSY\SYNC | output | Open drain output forced low while a command is executed; otherwise it can be configured to generate a synchronization signal. |
| 23 | CS | input | Chip select input pin for the serial interface. |
| 24 | FLAG | output | Open drain status flag output that is pulled to GND when a programmed alarm condition occurs. |
| 25 | STCK | input | Step-clock input. |
| 26 | VSA | power_in | Full bridge A power supply pin; it must be connected to VSB. |
| 27 | PGND | power_in | Power ground pin. |
| 28 | OUT2A | power_out | Full bridge A output 2. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | HTSSOP-28 |
| Category | Motor Driver ICs |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic interface supply voltage | VDD | | | 5.5 | V | | 9 |
| Motor supply voltage | VS | | | 48 | V | VSA = VSB = VS | 9 |
| Differential voltage between AGND, PGND and DGND | VGND,diff | -0.3 | | 0.3 | V | | 9 |
| Bootstrap peak voltage | Vboot | | | 55 | V | | 9 |
| Internal voltage regulator output pin and logic supply voltage | VREG | | | 3.6 | V | | 9 |
| Integrated ADC input voltage range (ADCIN pin) | VADCIN | -0.3 | | 3.6 | V | | 9 |
| OCSIN and OSCOUT pin voltage range | VOSC | -0.3 | | 3.6 | V | | 9 |
| Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins | Vout_diff | | | 48 | V | VSA = VSB = VS | 9 |
| Logic inputs voltage range | VLOGIC | -0.3 | | 5.5 | V | | 9 |
| R.m.s. output current | Iout | | | 3 | A | | 9 |
| Pulsed output current | Iout_peak | | | 7 | A | TPULSE < 1 ms | 9 |
| Operating junction temperature | TOP | -40 | | 150 | °C | | 9 |
| Storage temperature range | Ts | -55 | | 150 | °C | | 9 |
| Total power dissipation | Ptot | | | 5 | W | TA = 25 ºC; HTSSOP28 mounted on EVAL6470H | 9 |
| Motor supply voltage | VS | 8 | | 45 | V | VSA = VSB = VS | 10 |
| Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins | Vout_diff | | | 45 | V | VSA = VSB = VS | 10 |
| Logic supply voltage | VREG,in | 3.2 | | 3.3 | V | VREG voltage imposed by external source | 10 |
| Integrated ADC input voltage (ADCIN pin) | VADC | 0 | | | V | ADCIN pin; upper limit VREG | 10 |
| Thermal resistance junction ambient | RthJA | | 22 | | °C/W | HTSSOP28 mounted on EVAL6470H rev 1.0 board | 10 |
| UVLO turn-on threshold | VSthOn | 7.5 | 8.2 | 8.9 | V | | 11 |
| UVLO turn-off threshold | VSthOff | 6.6 | 7.2 | 7.8 | V | | 11 |
| UVLO threshold hysteresis | VSthHyst | 0.7 | 1 | 1.3 | V | | 11 |
| Quiescent motor supply current | Iq | | 0.5 | 0.65 | mA | Internal oscillator selected; VREG = 3.3 V ext.; CP floating | 11 |
| Thermal warning temperature | Tj(WRN) | | 130 | | °C | | 11 |
| Thermal shutdown temperature | Tj(SD) | | 160 | | °C | | 11 |
| Voltage swing for charge pump oscillator | Vpump | | 10 | | V | | 11 |
| Minimum charge pump oscillator frequency | fpump,min | 660 | | | kHz | | 11 |
| Maximum charge pump oscillator frequency | fpump,max | | | 800 | kHz | | 11 |
| Average boot current | Iboot | | 1.1 | 1.4 | mA | fsw,A = fsw,B = 15.6 kHz; POW_SR = '10' | 11 |
| High-side switch on-resistance | RDS(on) | | 0.37 | | ohm | Tj = 25 °C, Iout = 3 A | 11 |
| High-side switch on-resistance | RDS(on) | | 0.51 | | ohm | Tj = 125 °C, Iout = 3 A | 11 |
| Low-side switch on-resistance | RDS(on) | | 0.18 | | ohm | Tj = 25 °C, Iout = 3 A | 11 |
| Low-side switch on-resistance | RDS(on) | | 0.23 | | ohm | Tj = 125 °C, Iout = 3 A | 11 |
| High-side diode forward ON voltage | VSD,HS | 1 | 1.1 | | V | Iout = 1 A | 12 |
| Low-side diode forward ON voltage | VSD,LS | 1 | 1.1 | | V | Iout = 1 A | 12 |
| High-side diode reverse recovery time | trrHS | | 30 | | ns | Iout = 1 A | 12 |
| Low-side diode reverse recovery time | trrLS | | 100 | | ns | Iout = 1 A | 12 |
| Low logic level input voltage | VIL | | | 0.8 | V | | 12 |
| High logic level input voltage | VIH | 2 | | | V | | 12 |
| Low logic level output voltage | VOL | | | 0.3 | V | VDD = 3.3 V, IOL = 4 mA | 13 |
| High logic level output voltage | VOH | 2.4 | | | V | VDD = 3.3 V, IOH = 4 mA | 13 |
| High logic level output voltage | VOH | 4.7 | | | V | VDD = 5 V, IOH = 4 mA | 13 |
| CS pull-up and STBY pull-down resistors | RPU/RPD | 335 | 430 | 565 | k | CS = GND; STBY/RST = 5 V | 13 |
| Internal logic supply current | Ilogic | | 3.7 | 4.3 | mA | 3.3 V VREG externally supplied, internal oscillator | 13 |
| Standby mode internal logic supply current | Ilogic,STBY | | 2 | 2.5 | µA | 3.3 V VREG externally supplied | 13 |
| Step-clock input frequency | fSTCK | | | 2 | MHz | | 13 |
| Internal oscillator frequency | fosc,i | -3 | | 3 | % | Tj = 25 °C, VREG = 3.3 V | 13 |
| Internal oscillator frequency | fosc,i | | 16 | | MHz | Tj = 25 °C, VREG = 3.3 V | 13 |
| Programmable external oscillator frequency | fosc,e | 8 | | 32 | MHz | | 13 |
| OSCOUT clock source high level voltage | VOSCOUTH | 2.4 | | | V | Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA | 13 |
| OSCOUT clock source low level voltage | VOSCOUTL | | | 0.3 | V | Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA | 13 |
| Maximum SPI clock frequency | fCK,MAX | | | 5 | MHz | | 13 |
| SPI clock rise and fall time | trCK/tfCK | | | 25 | ns | CL = 30 pF | 13 |
| SPI clock high and low time | thCK/tlCK | 75 | | | ns | | 13 |
| Chip select setup time | tsetCS | 350 | | | ns | | 13 |
| Chip select hold time | tholCS | 10 | | | ns | | 13 |
| Deselect time | tdisCS | 800 | | | ns | | 13 |
| Data input setup time | tsetSDI | 25 | | | ns | | 13 |
| Data input hold time | tholSDI | 20 | | | ns | | 13 |
| Data output enable time | tenSDO | | | 38 | ns | | 14 |
| Data output disable time | tdisSDO | | | 47 | ns | | 14 |
| Data output valid time | tvSDO | | | 57 | ns | | 14 |
| Data output hold time | tholSDO | 37 | | | ns | | 14 |
| SW input pull-up resistance | RPUSW | 60 | 85 | 110 | k | SW = GND | 14 |
| Programmable PWM frequency | fPWM | 2.8 | | 62.5 | kHz | fosc = 16 MHz | 14 |
| Programmable PWM frequency | fPWM | 5.6 | | 125 | kHz | fosc = 32 MHz | 14 |
| PWM resolution | NPWM | | 8 | | bit | | 14 |
| Quiescent motor supply current in standby conditions | IqSTBY | | 26 | 34 | µA | VS = 8 V | 14 |
| Quiescent motor supply current in standby conditions | IqSTBY | | 30 | 36 | µA | VS = 36 V | 14 |
| Minimum standby time | tSTBY,min | 10 | | | s | | 14 |
| Logic power-on and wake-up time | tlogicwu | | 38 | 45 | µs | | 14 |
| Voltage regulator output voltage | VREG | 2.9 | 3 | 3.2 | V | | 14 |
| Voltage regulator output current | IREG | | | 40 | mA | | 14 |
| Voltage regulator output voltage drop | VREG,drop | | | 50 | mV | IREG = 40 mA | 14 |
| Voltage regulator standby output current | IREG,STBY | | | 10 | mA | | 14 |
| Analog-to-digital converter resolution | NADC | | 5 | | bit | | 14 |
## CAD (KiCad official)
- Symbol: `L6470H`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: HTSSOP-28 (KiCad packages3D, STEP)
- 3D model files: `l6470h-etched.step` / `l6470h-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l6470h.step` / `l6470h.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/l6470h.pdf) (73 pp, sha256 `4b94ab59eec71372`, retrieved 2026-11-06, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/l6470h-datasheet.pdf)