main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers l6470h: viewers · Ray
l6470h-etched.glb Publish 0.1.0 · Ray
l6470h-etched.step l6470h: factory component page (tier=mfr) · Ray
l6470h-hero.glb l6470h: hero GLB from the etched model (keeps the MPN mark) · Ray
l6470h-hero.overlay.json Publish 0.1.0 · Ray
l6470h.glb Publish 0.1.0 · Ray
l6470h.kicad_mod Publish 0.1.0 · Ray
l6470h.kicad_sym Publish 0.1.0 · Ray
l6470h.lbr Publish 0.1.0 · Ray
l6470h.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 29 pins · Ray

L6470H

STMicroelectronics · Stepper Motor Driver · HTSSOP-28

L6470H from STMicroelectronics, in a HTSSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT1A power_out Full bridge A output 1.
2 VSA power_in Full bridge A power supply pin; it must be connected to VSB.
3 STBY\RST input Standby and reset pin; LOW logic level resets the logic and puts the device into Standby mode, and if not used it should be connected to VDD.
4 SW input External switch input pin; if not used it should be connected to VDD.
5 ADCIN input Internal analog-to-digital converter input.
6 VREG power_out Internal 3 V voltage regulator output and 3.3 V external logic supply.
7 OSCIN input Oscillator pin 1 to connect an external oscillator or clock source; it should be left floating if unused.
8 OSCOUT output Oscillator pin 2 to connect an external oscillator; when the internal oscillator is used it can supply 2/4/8/16 MHz.
9 AGND power_in Analog ground.
10 CP output Charge pump oscillator output.
11 VBOOT power_in Bootstrap voltage needed for driving the high-side power DMOS of both bridges (A and B).
12 VSB power_in Full bridge B power supply pin; it must be connected to VSA.
13 PGND power_in Power ground pin.
14 OUT1B power_out Full bridge B output 1.
15 OUT2B power_out Full bridge B output 2.
16 VSB power_in Full bridge B power supply pin; it must be connected to VSA.
17 VDD power_in Logic outputs supply voltage (pull-up reference).
18 SDO output Data output pin for the serial interface.
19 CK input Serial interface clock input.
20 SDI input Data input pin for the serial interface.
21 DGND power_in Digital ground.
22 BUSY\SYNC output Open drain output forced low while a command is executed; otherwise it can be configured to generate a synchronization signal.
23 CS input Chip select input pin for the serial interface.
24 FLAG output Open drain status flag output that is pulled to GND when a programmed alarm condition occurs.
25 STCK input Step-clock input.
26 VSA power_in Full bridge A power supply pin; it must be connected to VSB.
27 PGND power_in Power ground pin.
28 OUT2A power_out Full bridge A output 2.
29 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package HTSSOP-28
Category Motor Driver ICs
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Logic interface supply voltage VDD 5.5 V 9
Motor supply voltage VS 48 V VSA = VSB = VS 9
Differential voltage between AGND, PGND and DGND VGND,diff -0.3 0.3 V 9
Bootstrap peak voltage Vboot 55 V 9
Internal voltage regulator output pin and logic supply voltage VREG 3.6 V 9
Integrated ADC input voltage range (ADCIN pin) VADCIN -0.3 3.6 V 9
OCSIN and OSCOUT pin voltage range VOSC -0.3 3.6 V 9
Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins Vout_diff 48 V VSA = VSB = VS 9
Logic inputs voltage range VLOGIC -0.3 5.5 V 9
R.m.s. output current Iout 3 A 9
Pulsed output current Iout_peak 7 A TPULSE < 1 ms 9
Operating junction temperature TOP -40 150 °C 9
Storage temperature range Ts -55 150 °C 9
Total power dissipation Ptot 5 W TA = 25 ºC; HTSSOP28 mounted on EVAL6470H 9
Motor supply voltage VS 8 45 V VSA = VSB = VS 10
Differential voltage between VSA, OUT1A, OUT2A, PGND and VSB, OUT1B, OUT2B, PGND pins Vout_diff 45 V VSA = VSB = VS 10
Logic supply voltage VREG,in 3.2 3.3 V VREG voltage imposed by external source 10
Integrated ADC input voltage (ADCIN pin) VADC 0 V ADCIN pin; upper limit VREG 10
Thermal resistance junction ambient RthJA 22 °C/W HTSSOP28 mounted on EVAL6470H rev 1.0 board 10
UVLO turn-on threshold VSthOn 7.5 8.2 8.9 V 11
UVLO turn-off threshold VSthOff 6.6 7.2 7.8 V 11
UVLO threshold hysteresis VSthHyst 0.7 1 1.3 V 11
Quiescent motor supply current Iq 0.5 0.65 mA Internal oscillator selected; VREG = 3.3 V ext.; CP floating 11
Thermal warning temperature Tj(WRN) 130 °C 11
Thermal shutdown temperature Tj(SD) 160 °C 11
Voltage swing for charge pump oscillator Vpump 10 V 11
Minimum charge pump oscillator frequency fpump,min 660 kHz 11
Maximum charge pump oscillator frequency fpump,max 800 kHz 11
Average boot current Iboot 1.1 1.4 mA fsw,A = fsw,B = 15.6 kHz; POW_SR = '10' 11
High-side switch on-resistance RDS(on) 0.37 ohm Tj = 25 °C, Iout = 3 A 11
High-side switch on-resistance RDS(on) 0.51 ohm Tj = 125 °C, Iout = 3 A 11
Low-side switch on-resistance RDS(on) 0.18 ohm Tj = 25 °C, Iout = 3 A 11
Low-side switch on-resistance RDS(on) 0.23 ohm Tj = 125 °C, Iout = 3 A 11
High-side diode forward ON voltage VSD,HS 1 1.1 V Iout = 1 A 12
Low-side diode forward ON voltage VSD,LS 1 1.1 V Iout = 1 A 12
High-side diode reverse recovery time trrHS 30 ns Iout = 1 A 12
Low-side diode reverse recovery time trrLS 100 ns Iout = 1 A 12
Low logic level input voltage VIL 0.8 V 12
High logic level input voltage VIH 2 V 12
Low logic level output voltage VOL 0.3 V VDD = 3.3 V, IOL = 4 mA 13
High logic level output voltage VOH 2.4 V VDD = 3.3 V, IOH = 4 mA 13
High logic level output voltage VOH 4.7 V VDD = 5 V, IOH = 4 mA 13
CS pull-up and STBY pull-down resistors RPU/RPD 335 430 565 k CS = GND; STBY/RST = 5 V 13
Internal logic supply current Ilogic 3.7 4.3 mA 3.3 V VREG externally supplied, internal oscillator 13
Standby mode internal logic supply current Ilogic,STBY 2 2.5 µA 3.3 V VREG externally supplied 13
Step-clock input frequency fSTCK 2 MHz 13
Internal oscillator frequency fosc,i -3 3 % Tj = 25 °C, VREG = 3.3 V 13
Internal oscillator frequency fosc,i 16 MHz Tj = 25 °C, VREG = 3.3 V 13
Programmable external oscillator frequency fosc,e 8 32 MHz 13
OSCOUT clock source high level voltage VOSCOUTH 2.4 V Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA 13
OSCOUT clock source low level voltage VOSCOUTL 0.3 V Internal oscillator 3.3 V VREG externally supplied; IOSCOUT = 4 mA 13
Maximum SPI clock frequency fCK,MAX 5 MHz 13
SPI clock rise and fall time trCK/tfCK 25 ns CL = 30 pF 13
SPI clock high and low time thCK/tlCK 75 ns 13
Chip select setup time tsetCS 350 ns 13
Chip select hold time tholCS 10 ns 13
Deselect time tdisCS 800 ns 13
Data input setup time tsetSDI 25 ns 13
Data input hold time tholSDI 20 ns 13
Data output enable time tenSDO 38 ns 14
Data output disable time tdisSDO 47 ns 14
Data output valid time tvSDO 57 ns 14
Data output hold time tholSDO 37 ns 14
SW input pull-up resistance RPUSW 60 85 110 k SW = GND 14
Programmable PWM frequency fPWM 2.8 62.5 kHz fosc = 16 MHz 14
Programmable PWM frequency fPWM 5.6 125 kHz fosc = 32 MHz 14
PWM resolution NPWM 8 bit 14
Quiescent motor supply current in standby conditions IqSTBY 26 34 µA VS = 8 V 14
Quiescent motor supply current in standby conditions IqSTBY 30 36 µA VS = 36 V 14
Minimum standby time tSTBY,min 10 s 14
Logic power-on and wake-up time tlogicwu 38 45 µs 14
Voltage regulator output voltage VREG 2.9 3 3.2 V 14
Voltage regulator output current IREG 40 mA 14
Voltage regulator output voltage drop VREG,drop 50 mV IREG = 40 mA 14
Voltage regulator standby output current IREG,STBY 10 mA 14
Analog-to-digital converter resolution NADC 5 bit 14

CAD (KiCad official)

  • Symbol: L6470H
  • Footprint: Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm
  • 3D model: HTSSOP-28 (KiCad packages3D, STEP)
  • 3D model files: l6470h-etched.step / l6470h-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l6470h.step / l6470h.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (73 pp, sha256 4b94ab59eec71372, retrieved 2026-11-06, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF