main
Ray
Publish 0.1.0
6f8c4b1
L6205D013TR
STMicroelectronics · Motor Driver ICs · SO-20-300mil
L6205D013TR from STMicroelectronics, in a SO-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1A | input | Bridge A logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 2 | IN2A | input | Bridge A logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 3 | SENSEA | power_in | Bridge A source pin must be connected to power ground directly or through a sensing power resistor. |
| 4 | OUT1A | power_out | Bridge A power output 1 of the half bridge. |
| 5 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 6 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 7 | OUT1B | power_out | Bridge B power output 1 of the half bridge. |
| 8 | SENSEB | power_in | Bridge B source pin must be connected to power ground directly or through a sensing power resistor. |
| 9 | IN1B | input | Bridge B logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 10 | IN2B | input | Bridge B logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 11 | ENB | input | Bridge B enable: a LOW logic level switches off all power MOSFETs of bridge B, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical). |
| 12 | VBOOT | power_out | Bootstrap voltage for driving the upper power MOSFETs of both bridges, with an absolute maximum of VS + 10 V. |
| 13 | OUT2B | power_out | Bridge B power output 2 of the half bridge. |
| 14 | VSB | power_in | Bridge B power supply, which must be connected to the supply voltage together with VSA; operating supply range is 8 V to 52 V. |
| 15 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 16 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 17 | VSA | power_in | Bridge A power supply, which must be connected to the supply voltage together with VSB; operating supply range is 8 V to 52 V. |
| 18 | OUT2A | power_out | Bridge A power output 2 of the half bridge. |
| 19 | VCP | output | Charge pump oscillator output, a square wave of about 600 kHz typical with 10 V amplitude. |
| 20 | ENA | input | Bridge A enable: a LOW logic level switches off all power MOSFETs of bridge A, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical). |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-20-300mil |
| Category | Power Management ICs |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VS | 8 | 52 | V | VSA = VSB = VS | 2 | |
| Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB | VOD | 52 | V | VSA = VSB = VS; VSENSEA = VSENSEB | 2 | ||
| Voltage Range at pins SENSEA and SENSEB (pulsed) | VSENSEA, VSENSEB | -6 | 6 | V | pulsed tW < trr | 2 | |
| Voltage Range at pins SENSEA and SENSEB (DC) | VSENSEA, VSENSEB | -1 | 1 | V | DC | 2 | |
| RMS Output Current | IOUT | 2.8 | A | 2 | |||
| Operating Junction Temperature | Tj | -25 | 125 | °C | 2 | ||
| Switching Frequency | fsw | 100 | KHz | 2 | |||
| Supply Voltage | VS | 60 | V | VSA = VSB = VS | 2 | ||
| Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB | VOD | 60 | V | VSA = VSB = VS = 60V; VSENSEA = VSENSEB = GND | 2 | ||
| Input and Enable Voltage Range | VIN,VEN | -0.3 | 7 | V | 2 | ||
| Voltage Range at pins SENSEA and SENSEB | VSENSEA, VSENSEB | -1 | 4 | V | 2 | ||
| Pulsed Supply Current (for each VS pin) | IS(peak) | 7.1 | A | VSA = VSB = VS; tPULSE < 1ms | 2 | ||
| RMS Supply Current (for each VS pin) | IS | 2.8 | A | VSA = VSB = VS | 2 | ||
| Storage and Operating Temperature Range | Tstg, TOP | -40 | 150 | °C | 2 | ||
| Maximum Thermal Resistance Junction-Pins | Rth-j-pins | 14 | °C/W | SO20 package | 3 | ||
| Maximum Thermal Resistance Junction-Ambient 1 | Rth-j-amb1 | 51 | °C/W | Multi-layer FR4 PCB, dissipating copper surface 6cm2 (35µm) on bottom side | 3 | ||
| Maximum Thermal Resistance Junction-Ambient 4 | Rth-j-amb2 | 77 | °C/W | Multi-layer FR4 PCB without any heat sinking surface | 3 | ||
| Turn-on Threshold | VSth(ON) | 6.6 | 7 | 7.4 | V | 5 | |
| Turn-off Threshold | VSth(OFF) | 5.6 | 6 | 6.4 | V | 5 | |
| Quiescent Supply Current | IS | 5 | 10 | mA | All Bridges OFF; Tj = -25°C to 125°C | 5 | |
| High-Side Switch ON Resistance | RDS(ON) | 0.34 | 0.4 | Ω | Tj = 25 °C | 5 | |
| High-Side Switch ON Resistance | RDS(ON) | 0.53 | 0.59 | Ω | Tj = 125 °C | 5 | |
| Low-Side Switch ON Resistance | RDS(ON) | 0.28 | 0.34 | Ω | Tj = 25 °C | 5 | |
| Low-Side Switch ON Resistance | RDS(ON) | 0.47 | 0.53 | Ω | Tj = 125 °C | 5 | |
| Leakage Current | IDSS | 2 | mA | EN = Low; OUT = VS | 5 | ||
| Leakage Current | IDSS | -0.15 | mA | EN = Low; OUT = GND | 5 | ||
| Forward ON Voltage | VSD | 1.15 | 1.3 | V | ISD = 2.8A, EN = LOW | 5 | |
| Reverse Recovery Time | trr | 300 | ns | If = 2.8A | 5 | ||
| Forward Recovery Time | tfr | 200 | ns | 5 | |||
| Low level logic input voltage | VIL | -0.3 | 0.8 | V | 5 | ||
| High level logic input voltage | VIH | 2 | 7 | V | 5 | ||
| Low Level Logic Input Current | IIL | -10 | µA | GND Logic Input Voltage | 5 | ||
| High Level Logic Input Current | IIH | 10 | µA | 7V Logic Input Voltage | 5 | ||
| Turn-on Input Threshold | Vth(ON) | 1.8 | 2 | V | 5 | ||
| Turn-off Input Threshold | Vth(OFF) | 0.8 | 1.3 | V | 5 | ||
| Input Threshold Hysteresis | Vth(HYS) | 0.25 | 0.5 | V | 5 | ||
| Enable to out turn ON delay time | tD(on)EN | 100 | 250 | 400 | ns | ILOAD = 2.8A, Resistive Load | 5 |
| Input to out turn ON delay time | tD(on)IN | 1.6 | µs | ILOAD = 2.8A, Resistive Load (dead time included) | 5 | ||
| Output rise time | tRISE | 40 | 250 | ns | ILOAD = 2.8A, Resistive Load | 5 | |
| Enable to out turn OFF delay time | tD(off)EN | 300 | 550 | 800 | ns | ILOAD = 2.8A, Resistive Load | 5 |
| Input to out turn OFF delay time | tD(off)IN | 600 | ns | ILOAD = 2.8A, Resistive Load | 6 | ||
| Output Fall Time | tFALL | 40 | 250 | ns | ILOAD = 2.8A, Resistive Load | 6 | |
| Dead Time Protection | tdt | 0.5 | 1 | µs | 6 | ||
| Charge pump frequency | fCP | 0.6 | 1 | MHz | -25°C < Tj < 125°C | 6 | |
| Input Supply Overcurrent Protection Threshold | ISOVER | 4 | 5.6 | 7.1 | A | Tj = -25°C to 125°C | 6 |
| Open Drain ON Resistance | ROPDR | 40 | 60 | Ω | I = 4mA | 6 | |
| OCD Turn-on Delay Time | tOCD(ON) | 200 | ns | I = 4mA; CEN < 100pF | 6 | ||
| OCD Turn-off Delay Time | tOCD(OFF) | 100 | ns | I = 4mA; CEN < 100pF | 6 |
CAD (KiCad official)
- Symbol:
L6205D013TR - Footprint:
Package_SO:SO-20-1EP_7.52x12.825mm_P1.27mm_EP6.045x12.09mm_Mask3.56x4.47mm - 3D model: SO-20-300mil, generated on the KiCad land (body 7.5 x 12.8 mm, terminals on the pads, 2.5 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
l6205d013tr-etched.step/l6205d013tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l6205d013tr.step/l6205d013tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (21 pp, sha256
7c56e39dd8d3a140, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# L6205D013TR
**STMicroelectronics** · Motor Driver ICs · SO-20-300mil
L6205D013TR from STMicroelectronics, in a SO-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1A | input | Bridge A logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 2 | IN2A | input | Bridge A logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 3 | SENSEA | power_in | Bridge A source pin must be connected to power ground directly or through a sensing power resistor. |
| 4 | OUT1A | power_out | Bridge A power output 1 of the half bridge. |
| 5 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 6 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 7 | OUT1B | power_out | Bridge B power output 1 of the half bridge. |
| 8 | SENSEB | power_in | Bridge B source pin must be connected to power ground directly or through a sensing power resistor. |
| 9 | IN1B | input | Bridge B logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 10 | IN2B | input | Bridge B logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V. |
| 11 | ENB | input | Bridge B enable: a LOW logic level switches off all power MOSFETs of bridge B, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical). |
| 12 | VBOOT | power_out | Bootstrap voltage for driving the upper power MOSFETs of both bridges, with an absolute maximum of VS + 10 V. |
| 13 | OUT2B | power_out | Bridge B power output 2 of the half bridge. |
| 14 | VSB | power_in | Bridge B power supply, which must be connected to the supply voltage together with VSA; operating supply range is 8 V to 52 V. |
| 15 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 16 | GND | power_in | Signal ground terminal, also used for heat dissipation toward the PCB in the SO package. |
| 17 | VSA | power_in | Bridge A power supply, which must be connected to the supply voltage together with VSB; operating supply range is 8 V to 52 V. |
| 18 | OUT2A | power_out | Bridge A power output 2 of the half bridge. |
| 19 | VCP | output | Charge pump oscillator output, a square wave of about 600 kHz typical with 10 V amplitude. |
| 20 | ENA | input | Bridge A enable: a LOW logic level switches off all power MOSFETs of bridge A, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical). |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-20-300mil |
| Category | Power Management ICs |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VS | 8 | | 52 | V | VSA = VSB = VS | 2 |
| Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB | VOD | | | 52 | V | VSA = VSB = VS; VSENSEA = VSENSEB | 2 |
| Voltage Range at pins SENSEA and SENSEB (pulsed) | VSENSEA, VSENSEB | -6 | | 6 | V | pulsed tW < trr | 2 |
| Voltage Range at pins SENSEA and SENSEB (DC) | VSENSEA, VSENSEB | -1 | | 1 | V | DC | 2 |
| RMS Output Current | IOUT | | | 2.8 | A | | 2 |
| Operating Junction Temperature | Tj | -25 | | 125 | °C | | 2 |
| Switching Frequency | fsw | | | 100 | KHz | | 2 |
| Supply Voltage | VS | | | 60 | V | VSA = VSB = VS | 2 |
| Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB | VOD | | | 60 | V | VSA = VSB = VS = 60V; VSENSEA = VSENSEB = GND | 2 |
| Input and Enable Voltage Range | VIN,VEN | -0.3 | | 7 | V | | 2 |
| Voltage Range at pins SENSEA and SENSEB | VSENSEA, VSENSEB | -1 | | 4 | V | | 2 |
| Pulsed Supply Current (for each VS pin) | IS(peak) | | | 7.1 | A | VSA = VSB = VS; tPULSE < 1ms | 2 |
| RMS Supply Current (for each VS pin) | IS | | | 2.8 | A | VSA = VSB = VS | 2 |
| Storage and Operating Temperature Range | Tstg, TOP | -40 | | 150 | °C | | 2 |
| Maximum Thermal Resistance Junction-Pins | Rth-j-pins | | | 14 | °C/W | SO20 package | 3 |
| Maximum Thermal Resistance Junction-Ambient 1 | Rth-j-amb1 | | | 51 | °C/W | Multi-layer FR4 PCB, dissipating copper surface 6cm2 (35µm) on bottom side | 3 |
| Maximum Thermal Resistance Junction-Ambient 4 | Rth-j-amb2 | | | 77 | °C/W | Multi-layer FR4 PCB without any heat sinking surface | 3 |
| Turn-on Threshold | VSth(ON) | 6.6 | 7 | 7.4 | V | | 5 |
| Turn-off Threshold | VSth(OFF) | 5.6 | 6 | 6.4 | V | | 5 |
| Quiescent Supply Current | IS | | 5 | 10 | mA | All Bridges OFF; Tj = -25°C to 125°C | 5 |
| High-Side Switch ON Resistance | RDS(ON) | | 0.34 | 0.4 | Ω | Tj = 25 °C | 5 |
| High-Side Switch ON Resistance | RDS(ON) | | 0.53 | 0.59 | Ω | Tj = 125 °C | 5 |
| Low-Side Switch ON Resistance | RDS(ON) | | 0.28 | 0.34 | Ω | Tj = 25 °C | 5 |
| Low-Side Switch ON Resistance | RDS(ON) | | 0.47 | 0.53 | Ω | Tj = 125 °C | 5 |
| Leakage Current | IDSS | | | 2 | mA | EN = Low; OUT = VS | 5 |
| Leakage Current | IDSS | -0.15 | | | mA | EN = Low; OUT = GND | 5 |
| Forward ON Voltage | VSD | | 1.15 | 1.3 | V | ISD = 2.8A, EN = LOW | 5 |
| Reverse Recovery Time | trr | | | 300 | ns | If = 2.8A | 5 |
| Forward Recovery Time | tfr | | | 200 | ns | | 5 |
| Low level logic input voltage | VIL | -0.3 | | 0.8 | V | | 5 |
| High level logic input voltage | VIH | 2 | | 7 | V | | 5 |
| Low Level Logic Input Current | IIL | -10 | | | µA | GND Logic Input Voltage | 5 |
| High Level Logic Input Current | IIH | | | 10 | µA | 7V Logic Input Voltage | 5 |
| Turn-on Input Threshold | Vth(ON) | | 1.8 | 2 | V | | 5 |
| Turn-off Input Threshold | Vth(OFF) | 0.8 | 1.3 | | V | | 5 |
| Input Threshold Hysteresis | Vth(HYS) | | 0.25 | 0.5 | V | | 5 |
| Enable to out turn ON delay time | tD(on)EN | 100 | 250 | 400 | ns | ILOAD = 2.8A, Resistive Load | 5 |
| Input to out turn ON delay time | tD(on)IN | | | 1.6 | µs | ILOAD = 2.8A, Resistive Load (dead time included) | 5 |
| Output rise time | tRISE | | 40 | 250 | ns | ILOAD = 2.8A, Resistive Load | 5 |
| Enable to out turn OFF delay time | tD(off)EN | 300 | 550 | 800 | ns | ILOAD = 2.8A, Resistive Load | 5 |
| Input to out turn OFF delay time | tD(off)IN | | | 600 | ns | ILOAD = 2.8A, Resistive Load | 6 |
| Output Fall Time | tFALL | | 40 | 250 | ns | ILOAD = 2.8A, Resistive Load | 6 |
| Dead Time Protection | tdt | 0.5 | 1 | | µs | | 6 |
| Charge pump frequency | fCP | | 0.6 | 1 | MHz | -25°C < Tj < 125°C | 6 |
| Input Supply Overcurrent Protection Threshold | ISOVER | 4 | 5.6 | 7.1 | A | Tj = -25°C to 125°C | 6 |
| Open Drain ON Resistance | ROPDR | | 40 | 60 | Ω | I = 4mA | 6 |
| OCD Turn-on Delay Time | tOCD(ON) | | | 200 | ns | I = 4mA; CEN < 100pF | 6 |
| OCD Turn-off Delay Time | tOCD(OFF) | | | 100 | ns | I = 4mA; CEN < 100pF | 6 |
## CAD (KiCad official)
- Symbol: `L6205D013TR`
- Footprint: `Package_SO:SO-20-1EP_7.52x12.825mm_P1.27mm_EP6.045x12.09mm_Mask3.56x4.47mm`
- 3D model: SO-20-300mil, generated on the KiCad land (body 7.5 x 12.8 mm, terminals on the pads, 2.5 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `l6205d013tr-etched.step` / `l6205d013tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l6205d013tr.step` / `l6205d013tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](docs/l6205d013tr-datasheet.pdf) (21 pp, sha256 `7c56e39dd8d3a140`, retrieved 2026-11-13, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/l6205d013tr-datasheet.pdf)