Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

L6205D013TR

STMicroelectronics · Motor Driver ICs · SO-20-300mil

L6205D013TR from STMicroelectronics, in a SO-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN1A input Bridge A logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V.
2 IN2A input Bridge A logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V.
3 SENSEA power_in Bridge A source pin must be connected to power ground directly or through a sensing power resistor.
4 OUT1A power_out Bridge A power output 1 of the half bridge.
5 GND power_in Signal ground terminal, also used for heat dissipation toward the PCB in the SO package.
6 GND power_in Signal ground terminal, also used for heat dissipation toward the PCB in the SO package.
7 OUT1B power_out Bridge B power output 1 of the half bridge.
8 SENSEB power_in Bridge B source pin must be connected to power ground directly or through a sensing power resistor.
9 IN1B input Bridge B logic input 1 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V.
10 IN2B input Bridge B logic input 2 is TTL/CMOS and µC compatible, with a typical turn-on threshold of 1.8 V and turn-off threshold of 1.3 V.
11 ENB input Bridge B enable: a LOW logic level switches off all power MOSFETs of bridge B, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical).
12 VBOOT power_out Bootstrap voltage for driving the upper power MOSFETs of both bridges, with an absolute maximum of VS + 10 V.
13 OUT2B power_out Bridge B power output 2 of the half bridge.
14 VSB power_in Bridge B power supply, which must be connected to the supply voltage together with VSA; operating supply range is 8 V to 52 V.
15 GND power_in Signal ground terminal, also used for heat dissipation toward the PCB in the SO package.
16 GND power_in Signal ground terminal, also used for heat dissipation toward the PCB in the SO package.
17 VSA power_in Bridge A power supply, which must be connected to the supply voltage together with VSB; operating supply range is 8 V to 52 V.
18 OUT2A power_out Bridge A power output 2 of the half bridge.
19 VCP output Charge pump oscillator output, a square wave of about 600 kHz typical with 10 V amplitude.
20 ENA input Bridge A enable: a LOW logic level switches off all power MOSFETs of bridge A, and the pin is also tied to the overcurrent/thermal protection transistor collector; if unused it must be connected to +5 V through a resistor, with 2.2 kΩ to 180 kΩ recommended (100 kΩ typical).
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SO-20-300mil
Category Power Management ICs
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VS 8 52 V VSA = VSB = VS 2
Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB VOD 52 V VSA = VSB = VS; VSENSEA = VSENSEB 2
Voltage Range at pins SENSEA and SENSEB (pulsed) VSENSEA, VSENSEB -6 6 V pulsed tW < trr 2
Voltage Range at pins SENSEA and SENSEB (DC) VSENSEA, VSENSEB -1 1 V DC 2
RMS Output Current IOUT 2.8 A 2
Operating Junction Temperature Tj -25 125 °C 2
Switching Frequency fsw 100 KHz 2
Supply Voltage VS 60 V VSA = VSB = VS 2
Differential Voltage between VSA, OUT1A, OUT2A, SENSEA and VSB, OUT1B, OUT2B, SENSEB VOD 60 V VSA = VSB = VS = 60V; VSENSEA = VSENSEB = GND 2
Input and Enable Voltage Range VIN,VEN -0.3 7 V 2
Voltage Range at pins SENSEA and SENSEB VSENSEA, VSENSEB -1 4 V 2
Pulsed Supply Current (for each VS pin) IS(peak) 7.1 A VSA = VSB = VS; tPULSE < 1ms 2
RMS Supply Current (for each VS pin) IS 2.8 A VSA = VSB = VS 2
Storage and Operating Temperature Range Tstg, TOP -40 150 °C 2
Maximum Thermal Resistance Junction-Pins Rth-j-pins 14 °C/W SO20 package 3
Maximum Thermal Resistance Junction-Ambient 1 Rth-j-amb1 51 °C/W Multi-layer FR4 PCB, dissipating copper surface 6cm2 (35µm) on bottom side 3
Maximum Thermal Resistance Junction-Ambient 4 Rth-j-amb2 77 °C/W Multi-layer FR4 PCB without any heat sinking surface 3
Turn-on Threshold VSth(ON) 6.6 7 7.4 V 5
Turn-off Threshold VSth(OFF) 5.6 6 6.4 V 5
Quiescent Supply Current IS 5 10 mA All Bridges OFF; Tj = -25°C to 125°C 5
High-Side Switch ON Resistance RDS(ON) 0.34 0.4 Ω Tj = 25 °C 5
High-Side Switch ON Resistance RDS(ON) 0.53 0.59 Ω Tj = 125 °C 5
Low-Side Switch ON Resistance RDS(ON) 0.28 0.34 Ω Tj = 25 °C 5
Low-Side Switch ON Resistance RDS(ON) 0.47 0.53 Ω Tj = 125 °C 5
Leakage Current IDSS 2 mA EN = Low; OUT = VS 5
Leakage Current IDSS -0.15 mA EN = Low; OUT = GND 5
Forward ON Voltage VSD 1.15 1.3 V ISD = 2.8A, EN = LOW 5
Reverse Recovery Time trr 300 ns If = 2.8A 5
Forward Recovery Time tfr 200 ns 5
Low level logic input voltage VIL -0.3 0.8 V 5
High level logic input voltage VIH 2 7 V 5
Low Level Logic Input Current IIL -10 µA GND Logic Input Voltage 5
High Level Logic Input Current IIH 10 µA 7V Logic Input Voltage 5
Turn-on Input Threshold Vth(ON) 1.8 2 V 5
Turn-off Input Threshold Vth(OFF) 0.8 1.3 V 5
Input Threshold Hysteresis Vth(HYS) 0.25 0.5 V 5
Enable to out turn ON delay time tD(on)EN 100 250 400 ns ILOAD = 2.8A, Resistive Load 5
Input to out turn ON delay time tD(on)IN 1.6 µs ILOAD = 2.8A, Resistive Load (dead time included) 5
Output rise time tRISE 40 250 ns ILOAD = 2.8A, Resistive Load 5
Enable to out turn OFF delay time tD(off)EN 300 550 800 ns ILOAD = 2.8A, Resistive Load 5
Input to out turn OFF delay time tD(off)IN 600 ns ILOAD = 2.8A, Resistive Load 6
Output Fall Time tFALL 40 250 ns ILOAD = 2.8A, Resistive Load 6
Dead Time Protection tdt 0.5 1 µs 6
Charge pump frequency fCP 0.6 1 MHz -25°C < Tj < 125°C 6
Input Supply Overcurrent Protection Threshold ISOVER 4 5.6 7.1 A Tj = -25°C to 125°C 6
Open Drain ON Resistance ROPDR 40 60 Ω I = 4mA 6
OCD Turn-on Delay Time tOCD(ON) 200 ns I = 4mA; CEN < 100pF 6
OCD Turn-off Delay Time tOCD(OFF) 100 ns I = 4mA; CEN < 100pF 6

CAD (KiCad official)

  • Symbol: L6205D013TR
  • Footprint: Package_SO:SO-20-1EP_7.52x12.825mm_P1.27mm_EP6.045x12.09mm_Mask3.56x4.47mm
  • 3D model: SO-20-300mil, generated on the KiCad land (body 7.5 x 12.8 mm, terminals on the pads, 2.5 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: l6205d013tr-etched.step / l6205d013tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l6205d013tr.step / l6205d013tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (21 pp, sha256 7c56e39dd8d3a140, retrieved 2026-11-13, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF