main
History Download
Ray Publish 0.1.0 a5ea3cd

L4973D5.1

STMicroelectronics · DC-DC Converters · SO-20-300mil

L4973D5.1 from STMicroelectronics, in a SO-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OSC passive An external resistor from the unregulated input voltage to pin 1 and a capacitor from pin 1 to ground fix the switching frequency, with line feed forward obtained automatically.
2 OUT output Step-down regulator output; absolute maximum output DC voltage is -1 V and peak voltage is -5 V at t = 0.1 µs.
3 OUT output Step-down regulator output; absolute maximum output DC voltage is -1 V and peak voltage is -5 V at t = 0.1 µs.
4 GND power_in Signal ground.
5 GND power_in Signal ground.
6 GND power_in Signal ground.
7 GND power_in Signal ground.
8 VCC power_in Unregulated DC input voltage; the operating input voltage range is 8 V to 55 V and the absolute maximum input voltage is 58 V.
9 VCC power_in Unregulated DC input voltage; the operating input voltage range is 8 V to 55 V and the absolute maximum input voltage is 58 V.
10 BOOT passive A capacitor connected between this pin and the output allows the internal D-MOS to be driven, with a bootstrap voltage limit of 70 V.
11 INH input A logic signal (active high) disables the device in sleep mode; if not used it must be connected to GND, and if floating the device is disabled.
12 COMP passive E/A output used for frequency compensation.
13 VFB input Step-down feedback input; connecting the output directly to this pin gives 3.3 V for L4973V3.3 and 5.1 V for L4973V5.1, and an external resistive divider is required for higher output voltages.
14 GND power_in Signal ground.
15 GND power_in Signal ground.
16 GND power_in Signal ground.
17 GND power_in Signal ground.
18 V5.1 output Precise 5.1 V reference voltage externally available (1.5% accuracy).
19 SS passive Soft-start pin, with soft-start charge current of 30 to 60 µA as stated in the electrical characteristics.
20 SYNC bidirectional Input/output synchronization pin; high input voltage is 3.5 V minimum and low input voltage is 0.9 V maximum.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SO-20-300mil
Category Power Management ICs
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range 8 55 V VO = VREF to 40 V; IO = 3.5A 6
Output voltage L4973V5.1 5.05 5.1 5.15 V IO = 1 A 6
Output voltage L4973V5.1 5 5.1 5.2 V IO = 0.5 A to 3.5 A; VCC = 8 V to 55 V 6
Output voltage L4973V5.1 4.95 5.1 5.25 V (2) IO = 0.5 A to 3.5 A; VCC = 8 V to 55 V 6
RDS(on) RDS(on) 0.15 0.22 Ω VCC = 10.5 V; IO = 3.5 A 6
RDS(on) RDS(on) 0.35 Ω (2) 6
Maximum limiting current 3.8 4.5 5.5 A (2) VCC = 8 V to 55 V 6
Maximum limiting current 4 4.5 5.5 A 6
Efficiency η 90 % VO = 5.1 V; IO = 3.5 A 6
Switching frequency 90 100 110 kHz (2) 6
Supply voltage ripple rejection 60 dB Vi = VCC+2 VRMS; VO = Vref; IO = 1 A; fripple = 100 Hz 6
Switching frequency stability vs. supply voltage Δfsw 2 5 % VCC = 8 V to 55 V 6
Reference voltage VREF 5.025 5.1 5.175 V Iref = 0 to 20 mA; VCC = 8 to 55 V 6
Reference voltage VREF 4.95 5.1 5.25 V (2) Iref = 0 to 20 mA; VCC = 8 to 55 V 6
Line regulation 5 10 mV Iref = 0 mA; VCC = 8 to 55 V 6
Short circuit current 30 65 100 mA 6
Soft-start charge current 30 45 60 μA 7
Soft-start discharge current 15 22 30 μA 7
Inhibit high level voltage 3 V (2) 7
Inhibit low level voltage 0.8 V (2) 7
Isource high level 10 16 50 μA VINH = 3 V; (2) 7
Isource low level 10 15 50 μA VINH = 0.8 V; (2) 7
Total operating quiescent current 4 6 mA Duty cycle = 50 % 7
Quiescent current 2.7 4 mA Duty cycle = 0 7
Total stand-by quiescent current 100 200 μA VCC = 24 V; VINH = 5 V 7
Total stand-by quiescent current 150 300 μA VCC = 55 V; VINH = 5 V 7
High level output voltage (error amplifier) 11 V 7
Low level output voltage (error amplifier) 0.65 V 7
Source bias current 1 2 3 μA 7
Source output current 200 300 600 μA 7
Sink output current 200 300 μA 7
Supply voltage ripple rejection (error amplifier) 60 80 dB VCOMP = VFB; CREF = 4.7 μF; 1-5 mA load current 7
DC open loop gain 50 60 dB RL = ∞ 7
Transconductance 2.5 mS Icomp = -0.1 to 0.1 mA; Vcomp = 6 V 7
Ramp valley 0.78 0.85 0.92 V 7
Ramp peak 1.9 2.1 2.3 V VCC = 8 V 7
Ramp peak 9 9.6 10.2 V VCC = 55 V 7
Maximum duty cycle 95 97 % 7
Maximum frequency 300 kHz Duty cycle = 0%; ROSC = 13 kΩ; COSC = 820 pF 8
Sync high input voltage 3.5 V VCC = 8 V to 55 V 8
Sync low input voltage 0.9 V VCC = 8 V to 55 V 8
Slave sink current 0.15 0.25 0.45 mA 8
Master output amplitude 4 4.5 V Isource = 3 mA 8
Output pulse width 0.2 0.35 μs No load; Vsync = 4.5 V 8
Input voltage V9,V8 58 V Input voltage (SO-20 column) 5
Output DC voltage V2,V3 -1 V Output DC voltage 5
Output peak voltage V2,V3 -5 V t = 0.1 μs; f = 200 kHz 5
Bootstrap voltage V10-V8 14 V Bootstrap voltage (V10-V8, SO-20 column) 5
Bootstrap voltage V10 70 V Bootstrap voltage 5
Analogs input voltage V12 12 V VCC = 24 V 5
Power dissipation Ptot 4 W SO-20; Tpins = 90 °C 5
Junction and storage temperature TJ,TSTG -40 150 °C 5
Thermal resistance junction-pin RthJP 15 °C/W SO-20 5
Thermal resistance junction-ambient RthJA 80 °C/W SO-20; package mounted on board 5

CAD (KiCad official)

  • Symbol: L4973D5.1
  • Footprint: Package_SO:SO-20-1EP_7.52x12.825mm_P1.27mm_EP6.045x12.09mm_Mask3.56x4.47mm
  • 3D model: SO-20-300mil (KiCad packages3D, STEP)
  • 3D model files: l4973d5-1-etched.step / l4973d5-1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); l4973d5-1.step / l4973d5-1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (28 pp, sha256 8bad7b96ec4d871a, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF