Generated by kicad-footprint-generator · KiCad file format 20260206
L4973D5.1
STMicroelectronics · DC-DC Converters · SO-20-300mil
L4973D5.1 from STMicroelectronics, in a SO-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OSC | passive | An external resistor from the unregulated input voltage to pin 1 and a capacitor from pin 1 to ground fix the switching frequency, with line feed forward obtained automatically. |
| 2 | OUT | output | Step-down regulator output; absolute maximum output DC voltage is -1 V and peak voltage is -5 V at t = 0.1 µs. |
| 3 | OUT | output | Step-down regulator output; absolute maximum output DC voltage is -1 V and peak voltage is -5 V at t = 0.1 µs. |
| 4 | GND | power_in | Signal ground. |
| 5 | GND | power_in | Signal ground. |
| 6 | GND | power_in | Signal ground. |
| 7 | GND | power_in | Signal ground. |
| 8 | VCC | power_in | Unregulated DC input voltage; the operating input voltage range is 8 V to 55 V and the absolute maximum input voltage is 58 V. |
| 9 | VCC | power_in | Unregulated DC input voltage; the operating input voltage range is 8 V to 55 V and the absolute maximum input voltage is 58 V. |
| 10 | BOOT | passive | A capacitor connected between this pin and the output allows the internal D-MOS to be driven, with a bootstrap voltage limit of 70 V. |
| 11 | INH | input | A logic signal (active high) disables the device in sleep mode; if not used it must be connected to GND, and if floating the device is disabled. |
| 12 | COMP | passive | E/A output used for frequency compensation. |
| 13 | VFB | input | Step-down feedback input; connecting the output directly to this pin gives 3.3 V for L4973V3.3 and 5.1 V for L4973V5.1, and an external resistive divider is required for higher output voltages. |
| 14 | GND | power_in | Signal ground. |
| 15 | GND | power_in | Signal ground. |
| 16 | GND | power_in | Signal ground. |
| 17 | GND | power_in | Signal ground. |
| 18 | V5.1 | output | Precise 5.1 V reference voltage externally available (1.5% accuracy). |
| 19 | SS | passive | Soft-start pin, with soft-start charge current of 30 to 60 µA as stated in the electrical characteristics. |
| 20 | SYNC | bidirectional | Input/output synchronization pin; high input voltage is 3.5 V minimum and low input voltage is 0.9 V maximum. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-20-300mil |
| Category | Power Management ICs |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range | 8 | 55 | V | VO = VREF to 40 V; IO = 3.5A | 6 | ||
| Output voltage L4973V5.1 | 5.05 | 5.1 | 5.15 | V | IO = 1 A | 6 | |
| Output voltage L4973V5.1 | 5 | 5.1 | 5.2 | V | IO = 0.5 A to 3.5 A; VCC = 8 V to 55 V | 6 | |
| Output voltage L4973V5.1 | 4.95 | 5.1 | 5.25 | V | (2) IO = 0.5 A to 3.5 A; VCC = 8 V to 55 V | 6 | |
| RDS(on) | RDS(on) | 0.15 | 0.22 | Ω | VCC = 10.5 V; IO = 3.5 A | 6 | |
| RDS(on) | RDS(on) | 0.35 | Ω | (2) | 6 | ||
| Maximum limiting current | 3.8 | 4.5 | 5.5 | A | (2) VCC = 8 V to 55 V | 6 | |
| Maximum limiting current | 4 | 4.5 | 5.5 | A | 6 | ||
| Efficiency | η | 90 | % | VO = 5.1 V; IO = 3.5 A | 6 | ||
| Switching frequency | 90 | 100 | 110 | kHz | (2) | 6 | |
| Supply voltage ripple rejection | 60 | dB | Vi = VCC+2 VRMS; VO = Vref; IO = 1 A; fripple = 100 Hz | 6 | |||
| Switching frequency stability vs. supply voltage | Δfsw | 2 | 5 | % | VCC = 8 V to 55 V | 6 | |
| Reference voltage | VREF | 5.025 | 5.1 | 5.175 | V | Iref = 0 to 20 mA; VCC = 8 to 55 V | 6 |
| Reference voltage | VREF | 4.95 | 5.1 | 5.25 | V | (2) Iref = 0 to 20 mA; VCC = 8 to 55 V | 6 |
| Line regulation | 5 | 10 | mV | Iref = 0 mA; VCC = 8 to 55 V | 6 | ||
| Short circuit current | 30 | 65 | 100 | mA | 6 | ||
| Soft-start charge current | 30 | 45 | 60 | μA | 7 | ||
| Soft-start discharge current | 15 | 22 | 30 | μA | 7 | ||
| Inhibit high level voltage | 3 | V | (2) | 7 | |||
| Inhibit low level voltage | 0.8 | V | (2) | 7 | |||
| Isource high level | 10 | 16 | 50 | μA | VINH = 3 V; (2) | 7 | |
| Isource low level | 10 | 15 | 50 | μA | VINH = 0.8 V; (2) | 7 | |
| Total operating quiescent current | 4 | 6 | mA | Duty cycle = 50 % | 7 | ||
| Quiescent current | 2.7 | 4 | mA | Duty cycle = 0 | 7 | ||
| Total stand-by quiescent current | 100 | 200 | μA | VCC = 24 V; VINH = 5 V | 7 | ||
| Total stand-by quiescent current | 150 | 300 | μA | VCC = 55 V; VINH = 5 V | 7 | ||
| High level output voltage (error amplifier) | 11 | V | 7 | ||||
| Low level output voltage (error amplifier) | 0.65 | V | 7 | ||||
| Source bias current | 1 | 2 | 3 | μA | 7 | ||
| Source output current | 200 | 300 | 600 | μA | 7 | ||
| Sink output current | 200 | 300 | μA | 7 | |||
| Supply voltage ripple rejection (error amplifier) | 60 | 80 | dB | VCOMP = VFB; CREF = 4.7 μF; 1-5 mA load current | 7 | ||
| DC open loop gain | 50 | 60 | dB | RL = ∞ | 7 | ||
| Transconductance | 2.5 | mS | Icomp = -0.1 to 0.1 mA; Vcomp = 6 V | 7 | |||
| Ramp valley | 0.78 | 0.85 | 0.92 | V | 7 | ||
| Ramp peak | 1.9 | 2.1 | 2.3 | V | VCC = 8 V | 7 | |
| Ramp peak | 9 | 9.6 | 10.2 | V | VCC = 55 V | 7 | |
| Maximum duty cycle | 95 | 97 | % | 7 | |||
| Maximum frequency | 300 | kHz | Duty cycle = 0%; ROSC = 13 kΩ; COSC = 820 pF | 8 | |||
| Sync high input voltage | 3.5 | V | VCC = 8 V to 55 V | 8 | |||
| Sync low input voltage | 0.9 | V | VCC = 8 V to 55 V | 8 | |||
| Slave sink current | 0.15 | 0.25 | 0.45 | mA | 8 | ||
| Master output amplitude | 4 | 4.5 | V | Isource = 3 mA | 8 | ||
| Output pulse width | 0.2 | 0.35 | μs | No load; Vsync = 4.5 V | 8 | ||
| Input voltage | V9,V8 | 58 | V | Input voltage (SO-20 column) | 5 | ||
| Output DC voltage | V2,V3 | -1 | V | Output DC voltage | 5 | ||
| Output peak voltage | V2,V3 | -5 | V | t = 0.1 μs; f = 200 kHz | 5 | ||
| Bootstrap voltage | V10-V8 | 14 | V | Bootstrap voltage (V10-V8, SO-20 column) | 5 | ||
| Bootstrap voltage | V10 | 70 | V | Bootstrap voltage | 5 | ||
| Analogs input voltage | V12 | 12 | V | VCC = 24 V | 5 | ||
| Power dissipation | Ptot | 4 | W | SO-20; Tpins = 90 °C | 5 | ||
| Junction and storage temperature | TJ,TSTG | -40 | 150 | °C | 5 | ||
| Thermal resistance junction-pin | RthJP | 15 | °C/W | SO-20 | 5 | ||
| Thermal resistance junction-ambient | RthJA | 80 | °C/W | SO-20; package mounted on board | 5 |
CAD (KiCad official)
- Symbol:
L4973D5.1 - Footprint:
Package_SO:SO-20-1EP_7.52x12.825mm_P1.27mm_EP6.045x12.09mm_Mask3.56x4.47mm - 3D model: SO-20-300mil (KiCad packages3D, STEP)
- 3D model files:
l4973d5-1-etched.step/l4973d5-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l4973d5-1.step/l4973d5-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (28 pp, sha256
8bad7b96ec4d871a, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).