Generated by kicad-footprint-generator · KiCad file format 20260206
KTH5701AQ2QNS
CONNTEK · Hall Sensor · QFN-16L(3x3)
KTH5701AQ2QNS from CONNTEK, in a QFN-16L(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INT | output | Data ready or wake-up & sleep mode interrupt output, set to 1 after a measurement completes or threshold change is exceeded and held until the measurement data is read back. |
| 2 | CS | input | Chip select: pull up to VDD_IO in I2C mode, active-low and driven by the SPI master in SPI mode. |
| 3 | SCL/SCLK | input | I2C or SPI clock input. |
| 4 | NC | unconnected | Not connected; datasheet recommends grounding all NC pins. |
| 5 | SDA/MOSI | bidirectional | I2C data input/output, or SPI data master-out slave-in. |
| 6 | MISO | output | SPI data master-in slave-out; short MISO and MOSI when using only 3-wire SPI data transfer. |
| 7 | BUTT_OUT/TRIG | bidirectional | Push-button function output or single-measurement trigger input; must be connected to ground when unused and must not float when used as trigger. |
| 8 | VDD_IO | power_in | IO power supply, recommended 1.8 V to VDD. |
| 9 | NC | unconnected | Not connected; datasheet recommends grounding all NC pins. |
| 10 | NC | unconnected | Not connected; datasheet recommends grounding all NC pins. |
| 11 | A1 | input | I2C address input A1; must be connected to ground in SPI mode. |
| 12 | A0 | input | I2C address input A0; must be connected to ground in SPI mode. |
| 13 | VSS | power_in | Ground. |
| 14 | NC | unconnected | Not connected; datasheet recommends grounding all NC pins. |
| 15 | VDD | power_in | Power supply, recommended 2.8 V to 5.5 V (3.3 V typical). |
| 16 | NC | unconnected | Not connected; datasheet recommends grounding all NC pins. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | CONNTEK |
| Package | QFN-16L(3x3) |
| Category | Sensors |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD_MAX | -0.3 | 6 | V | 6 | ||
| Digital IO Supply | VDD_IO_MAX | -0.3 | 6 | V | 6 | ||
| Maximum Storage Temperature | Tstorage | 150 | ℃ | 6 | |||
| Supply Voltage | VDD | 2.8 | 3.3 | 5.5 | V | 6 | |
| Digital IO Supply Voltage | VDD_IO | 1.8 | V | upper limit VDD | 6 | ||
| Input High Level Voltage | VIH | 0.75 | VDD_IO | 6 | |||
| Input Low Level Voltage | VIL | 0.25 | VDD_IO | 6 | |||
| AQ2 Industrial Grade Operating Temperature | TOPERATION | -40 | 25 | 105 | ℃ | AQ2 | 6 |
| Supply Voltage | VDD | 2.8 | 3.3 | 5.5 | V | 6 | |
| Digital IO Supply Voltage | VDD_IO | 1.8 | V | upper limit VDD | 6 | ||
| Conversion Current X-axis or Y-axis | IDD,CONVXY | 4.89 | mA | VDD=3.3V | 6 | ||
| Conversion Current Z-axis | IDD,CONVZ | 3.87 | mA | 6 | |||
| Conversion Current Temperature | IDD,CONVT | 2.58 | mA | 7 | |||
| Standby Current | IDD,STBY | 61.7 | μA | 7 | |||
| Wake-Up & Sleep Standby Current | IDD,WAKE_STBY | 2.4 | μA | 7 | |||
| Idle Current | IDD,IDLE | 1.4 | μA | 7 | |||
| Magnetic Flux Density Linear Range XY | Mxyrange | -130 | 130 | mT | @gain=20 | 7 | |
| Magnetic Flux Density Linear Range Z | Mzrange | -80 | 80 | mT | 7 | ||
| X-axis Sensitivity | SENSX | 65.5 | LSB/mT | 7 | |||
| Y-axis Sensitivity | SENSy | 65.5 | LSB/mT | 7 | |||
| Z-axis Sensitivity | SENSz | 102 | LSB/mT | 7 | |||
| XY Axis RMS Noise | NRMSxy | 0.2 | mT | @gain=20 magnOsr=0 digCtrl=0 | 7 | ||
| XY-Axis RMS Noise | NRMSxy | 0.03 | mT | @gain=20 magnOsr=3 digCtrl=0 | 7 | ||
| XY-Axis RMS Noise | NRMSxy | 0.01 | mT | @gain=20 magnOsr=3 digCtrl=4 | 7 | ||
| Z-Axis RMS Noise | NRMSz | 0.1 | mT | @gain=20 magnOsr=0 digCtrl=0 | 7 | ||
| Z-Axis RMS Noise | NRMSz | 0.02 | mT | @gain=20 magnOsr=3 digCtrl=0 | 7 | ||
| Z-Axis RMS Noise | NRMSz | 0.01 | mT | @gain=20 magnOsr=3 digCtrl=4 | 7 |
CAD (KiCad official)
- Symbol:
KTH5701AQ2QNS - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16L(3x3) (KiCad packages3D, STEP)
- 3D model files:
kth5701aq2qns-etched.step/kth5701aq2qns-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);kth5701aq2qns.step/kth5701aq2qns.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: CONNTEK datasheet (52 pp, sha256
08677d632af50a8f, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).